LG F1258RD2 Manuale utente
OWNER’S MANUAL
WASHING MACHINE
F1258RD
F1258RD2
F1258RD24
F1258RD29
F1258RD9
F1258RDW
F151258RD29
WD581202RC
WD581242RC
P/No.:MFL62526829 www.lg.com
Please read this manual carefully before operating
your washing machine and retain it for future reference.
roduct Feature
P
ontents
C
2
Warnings...............................................................................................3
Specification..........................................................................................5
Installation.............................................................................................6
Care before washing...........................................................................12
Adding detergent.................................................................................13
Function ..............................................................................................15
ow to use washer .............................................................................16
Maintenance .......................................................................................22
Troubleshooting guide ........................................................................26
Terms of Warranty ..............................................................................29
■Ultra Capacity
The Larger drum enables not just higher head drop and stronger
centrifugal force, but also less tangling and wrinkling of the laundry.
eavier loads, such as king size comforters, blankets, and curtains, can
be washed.
■Direct Drive System
The advanced Brushless DC motor directly drives the drum without belt
and pulley.
■Tilted Drum and Extra Large Door Opening
Tilted drum and extra large opening make it possible to load and unload
clothing more easily.
■Water Circulation
Spray detergent solution and water onto the load over and over.
Clothes are soaked more quickly and thoroughly during wash cycle.
The detergent suds can be removed more easily by the water shower
during rinse cycle. The water circulation system uses both water and
detergent more efficiently.
■RollerJets
Washing ball enhances the wash performance and reduces damage
to the clothing. The jets spray and help tumble clothes to enhance
washing performance while maintaining fabric care.
■Built-in Heater
Internal heater automatically heats the water to the best temperature on
selected cycles.
■Auto Restart
Auto Restart allows the program to restart all by itself in case of power
failure. It does from the stage where it stopped.
■Child Lock
The Child lock prevents children from pressing any button to change the
settings during operation.
추가선택 예약
추가선택 예약
arnings
W
3
For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, electric shock, or to prevent property damage,
personal injury, or loss of life.
!
READ ALL INSTRUCTIONS BEFORE USE
WA NING!
• Do not install or store the washer where it will
be exposed to the weather.
• Do not tamper with controls.
• Do not repair or replace any part of the washer
or attempt any servicing unless specifically
recommended in the user-maintenance
instructions or published user-repair instructions
that you understand and have the skills to carry
out.
• Keep the area underneath and around your
appliances free of combustible materials such as
lint, paper, rags, chemicals, etc.
• Close supervision is necessary if this appliance
is used by or near children.
Do not allow children to play on, with, or inside
this or any other appliance.
• Do not leave the washer door open.
An open door could entice children to hang on
the door or crawl inside the washer.
• Never reach into washer while it is moving. Wait
until the drum has completely stopped.
• The laundry process can reduce the flame
retardant of fabrics.
• Do not wash or dry articles that have been
cleaned in, washed in, soaked in, or spotted with
combustible or explosive substances (such as
wax, oil, paint, gasoline, degreasers, dry-
cleaning solvents, kerosene, etc.) which may
ignite or explode. Oil may remain in the tub after
a whole cycle resulting in fire during drying.
So, do not load oiled clothes.
• To avoid such a result, carefully follow the
garment manufacturer’s wash and care
instructions.
• Do not slam the washer door closed or try to
force the door open when locked. This could
result in damage to the washer.
• To minimize the possibility of electric shock,
unplug this appliance from the power supply or
disconnect the washer at the household
distribution panel by removing the fuse or
switching off the circuit breaker before
attempting any maintenance or cleaning.
• Never attempt to operate this appliance if it is
damaged, malfunctioning, partially
disassembled, or has missing or broken parts,
including a damaged cord or plug.
• Dryer is intended for only drying textile material.
• If the washer has been exposed to water, call an
authorized service provider to avoid any risk of
fire or electric shock.
G OUNDING INST UCTIONS
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk
of electric shock by providing a path of least resistance for electric current. This appliance is equipped with
a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance.
• Do not use an adapter or otherwise defeat the grounding plug.
• If you don’t have the proper outlet, consult an electrician.
IMPO TANT SAFETY INST UCTIONS
WA NING :To reduce the risk of fire, electric shock, or injury to persons when using
the washer, follow basic precautions, including the following:
SAVE THESE INST UCTIONS
WA NING :Improper connection of the equipment-grounding conductor can result in risk of electric
shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is
properly grounded. Do not modify the plug provided with the appliance - if it does not fit the outlet, have a
proper outlet installed by a qualified electrician.
arnings
W
4
To minimize the risk of fire in a tumble dryer, the following should be observed:
• Items that have been spotted or soaked with vegetable or cooking oil constitute a fire
hazard and should not be placed in a tumble dryer.
Oil-affected items can ignite spontaneously, especially when exposed to heat
sources Such as in a tumble dryer. The items become warm, causing an oxidation
reaction in the oil. Oxidation creates heat. If the heat cannot escape, the items can
become hot enough to catch fire. Piling, stacking or storing oil-affected items can
prevent heat from escaping and so create a fire hazard.
If it is unavoidable that fabrics that contain vegetable or cooking oil or have been
contaminated by hair care products be placed in a tumble dryer they should first be
washed in hot water with extra detergent-this will reduce, but not eliminate, the
hazard. Washed in hot water with extra detergent-this will reduce, but not
eliminate, the hazard. The ‘cool down’ cycle of tumble dryers should be used to
reduce the temperature of the items. They should not be removed from the tumble
dryer or piled or stacked while hot.
• Items that have been previously cleaned in, washed in, soaked in or spotted with
petrol/gasoline, dry-cleaning solvents or other flammable or explosive substances
should not be placed in a tumble dryer.
ighly flammable substances commonly used in domestic environments include
acetone, denatured alcohol, petrol/gasoline, kerosene, spot removers (some
brands), turpentine, waxes and was removers.
• Items containing foam rubber (also known as latex foam) or similarly testured rubber.
like materials should not be dried in a tumble dryer on a heat setting.
Foam rubber materials can, when heated, produce fire by spontaneous combustion.
• Fabric softeners or similar products should not be used in a tumble dryer to eliminate
the effects of static electricity unless this practice is specifically recommended by the
manufacturer of the fabric softener or product.
• Undergarments that contain metal reinforcements should not be placed in a tumble
dryer.
Damage to the tumble dryer can result if metal reinforcements come loose during
drying. When available a drying rack could be used for such items.
• Plastic articles such as shower caps or babies waterproof napkin covers should not
be placed in a tumble dryer.
• Rubber-backed articles, clothes fitted with foam rubber pads, pillows, galoshes and
rubber-coated tennis shoes should not be placed in a tumble dryer.
5
pecification
S
Name : Front loading washing machine
Power supply : 220–240 V~, 50 z
Size : 686 mm(W)×756 mm(D)×983 mm( )
Weight : 91 kg
Wash capacity/Max. Watt : 15 kg(2200 W)
Dry capacity/Max. Watt : 8 kg(2150 W)
Spin speed : 1200 rpm max.
Water consumption : 180ℓ
Permissible water pressure : 0.3-10 kgf/㎠(30-1000 kPa)
❋The appearance and specifications may be varied without notice to raise the
units quality.
Inlet hose(1EA) Spanner
Accessories
Control Panel
Shipping Bolts
Power Plug
• If the supply cord is damaged,
it must be replaced by the
manufacturer or its authorized
service technician in order to
avoid a hazard.
Drum
Drain Plug Drain Pump Filter
Lower cover cap
Door
Adjustable Feet
Drain Hose
Dispenser
Air Vent for Safety
Cold Water Inlet
Back of Washer
6
nstallation
I
1. To prevent internal damage during
transport, the special 4 bolts are locked.
Before operating the washer, remove
the bolts along with the rubber bungs.
• If they are not removed, it may cause heavy
vibration, noise and malfunction.
3. Take out the 4 bolts along with the rubber
bungs by slightly twisting the bung. Keep
the 4 bolts and the spanner for future use.
• Whenever the appliance is transported, the
transit bolts must be refitted.
The appliance is fitted with transit bolts to prevent internal damage during transport.
• Packing and all transit bolts must be
removed before using the washer.
When unpacking the base, be sure to
remove the additional packing
support in the middle of the base
packing.
2. Unscrew the 4 bolts with
the spanner supplied.
4. Close the holes with the caps supplied.
Transit bolts
Install or store where it will not be exposed to temperat res below freezing or exposed to the
weather.
Properly gro nd washer to conform with all governing codes and ordinances.
The base opening m st not be obstr cted by carpeting when the washing machine is installed on a
carpeted floor.
In co ntries where there are areas which may be s bject to infestation by cockroaches or other
vermin, pay partic lar attention to keeping the appliance and its s rro ndings in clean condition at
all times.
Any damage which may be ca se by cockroaches or other vermin will not be covered by the
appliance g arantee.
Removing transit bolts
Washer
Base Packing
Packing Support
7
nstallation
I
Level floor :
Allowable slope under entire washer is 1˚
Power outlet :
Must be within 1.5 meters of either side of location of
washer. Do not overload the outlet with more than one
appliance.
Additional Clearance :
For wall, door and floor modeling is required.
(10cm : rear /2cm:right & left side)
Do not place or store laundry products on top of
washer at any times.
They can damage the finish or controls.
Installation place requirement
Positioning
Install the washer on a flat hard floor.
Make sure that air circulation around the washer is not impeded by carpets,rug etc.
• Before placing the washer on tiles, apply a rubber mat under the feet.
• ever try to correct any unevenness in the floor with pieces of wood, cardboard or similar
materials under the washer.
• If it is impossible to avoid positioning the washer next to a gas cooker or coal burning
stove,an insulating(686x756x983mm) covered with aluminum foil on the side facing the
cooker or stove,must be inserted between the two appliance.
• The washer must not be installed in rooms where the temperature can drop below 0°C.
• Please ensure that when the washer is installed, it is easily accessible for the engineer in the
event of a breakdown.
• With the washer installed adjust all four feet using the transit bolt spanner provided ensuring
the appliance is stable, and a clearance of approximately 20mm is left between the top of
the washer and the underside of the work-top.
• The installation instructions shall state that the openings must not be obstructed by a carpet
if it has ventilation openings in the base.
Washer
Drain ose
Laundry
Tub
approx.
2cm
8
nstallation
I
▶Water supply pressure must be between 30kPa and 1000kPa (0.3~10kgf/cm2)
▶D n’t strip r cr ssthread when c nnecting Inlet h se t the valve.
▶If the water supply pressure is m re than 1000kPa, a dec mpressi n device
sh uld be installed.
• Two rubber seals are supplied with the water inlet hoses these are in
order to prevent water leaks.
• Check water tightness of washing machine connections by turning the tap
completely on.
• Periodically check the condition of the hose and replace the hose if
necessary.
• Make sure that there is no kink on the hose and that it is not crushed.
• The instructions for appliances connected to the water mains by
detachable hose-sets shall state that the new hose-sets supplied with the
appliance are to be used and that old hose-sets should not be reused.
Washing Machine is to be connected to the water mains using new hose-sets and that old
hose-sets should not be used.
Connecting water supply hose
1. Do not use an extension cord or double adapter.
2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or similarly
qualified person in order to avoid a hazard.
3. Always unplug the machine and turn off the water supply after use.
4. Connect the machine to an earthed socket in accordance with current wiring regulations.
5. The appliance must be positioned so that the plug is easily accessible.
• Repairs to the washing machine must only be carried out qualified personnel. Repairs carried out by
inexperienced persons may cause injury or serious malfunctioning. Contact your local service center
• Do not install your washing machine in rooms where temperatures below freezing may occur. Frozen hoses
may burst under pressure. The reliability of the electronic control unit may be impaired at temperatures below
freezing point.
• If the appliance is delivered in the winter months and temperatures are below freezing : Store the washing
machine at room temperature for a few hours before putting it into operation.
Electrical connection
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers
only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's
manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed
power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in
electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or
deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement
part by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a
door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the
appliance.
If this appliance is supplied from a cord extension set or electrical portable outlet device, the cord extension set
or electrical portable outlet device must be positioned so that it is not subject to splashing or ingress of moisture.
CAUTION
The appliance is not intended for use by young children or infirm persons without supervision.
Young Children should be supervised to ensure that they do not play with appliance.
CAUTION
Cold
Cold
water tap
ose connector
Sealing washer
NOTE
After completing connection, if water leaks from the hose, repeat the same steps. Use the most conventional type
of faucet for water supply. In case the faucet is square or too big, remove the spacing ring before inserting the
faucet into the adaptor.
9
nstallation
I
Normal Tap without thread & screw type inlet hose
Normal Tap without thread & one touch type inlet hose
1.Unscrew the fixing screw to
attach the tap.
2.Push the connector up till the
rubber packing is in tight contact
with the tap. Then tighten the 4
screws.
3.Push the water supply hose
vertically upwards so that the
rubber packing within in the hose
can adhere completely to the tap
and then tighten it by screwing it
to the right.
1.Untighten the upper connector
screw.
2.Push the upper connector up till
the rubber packing is in tight
contact with the tap. Then tighten
the 4 screws.
3. Connect the water supply hose to
the middle connector, pushing
the plate down.
• Your machine comes with only
cold water connection.
• Make sure that there are no
kinks in the hose and that it is
not crushed.
• Make sure that the rubber
seal is inside the hose
connector.
• In case the diameter of the
tap is large remove the guide
plate. • Turn the middle connector not
to have water leaked.
• To separate the water supply
hose from the middle connector
shut off the tap. Then pull the
inlet hose down, pushing the
plate down.
Upper
Connector
Upper
Connector
Upper Connector
Upper Connector
Upper Connector
Upper Connector
Plate
Plate
Water supply hose
Water supply hose
Fixing screw
Fixing screw
Rubber
packing
Rubber
packing
Middle
connector
Middle connector
ose
connector
Guide plate
Connector
Used the horizontal tap
orizontal tap
Extension tap
Square tap
Rubber
seal
Rubber packing
Rubber packing
10
nstallation
I
Installation of drain hose
• The drain hose should not be placed
higher than 100 cm above the floor.
• Proper securing of the drain hose will
protect the floor from damage due to
water leakage.
• When the drain hose is too long, do not
force back into the washer. This will
cause abnormal noise.
• When installing the drain hose sink,
secure it tightly with a string.
• Proper securing of the drain hose will
protect the floor from damage due to
water leakage.
This equipment is not designed for maritime use or for use mobile installations such as
caravans, aircraft etc.
Turn off the stopcock if the machine is to be left for any length of time (e.g. holiday),
especially if there is no floor drain(gully) in the immediate vicinity.
When disposing of the appliance, cut off the mains cable, and destroy the plug Disable the
door lock to prevent young children being trapped inside.
Packaging material (e.g. Films, Styrofoam) can be dangerous for children. There is a risk of
suffocation ! Keep all packaging well away from children
about 100 cm
about 100 cm
Laundry tub
ose
Retainer
Tie
strap
max. 100cm
min. 60cm
max. 100cm
min. 60cm
about 105 cm
about 105 cm
max. 100 cm
max. 100 cm
min. 60 cm
min. 60 cm
about 145 cm
about 145 cm
Questo manuale è adatto per i seguenti modelli
8
Indice
Altri manuali LG Rondella
LG
LG WFC1112ET Manuale utente
LG
LG T0866NEFPJ Manuale utente
LG
LG WT7900HBA Manuale utente
LG
LG FV1450S3V Manuale utente
LG
LG WF-A700 Manuale utente
LG
LG WM0642H Series Manuale di istruzioni
LG
LG F4WV910P2 Series Manuale utente
LG
LG F1255FD Manuale utente
LG
LG WM3997H*A Manuale utente
LG
LG T4432S0Z Manuale utente
LG
LG WV9142 RP Series Manuale utente
LG
LG WM3997H A /01 Series Manuale utente
LG
LG F20L2CRV2E2 Manuale utente
LG
LG WM22RV2S6 Manuale utente
LG
LG WT7700HVA Manuale utente
LG
LG F14A8Q/TD Series Manuale utente
LG
LG F1403AD Manuale utente
LG
LG F1261FD Manuale utente
LG
LG F4J7VS0W Manuale utente
LG
LG WM1377HW Series Manuale di istruzioni
