Lightwave LW301 Manuale utente
Connect Series
www.lightwaverf.house
Instruction Manual
Version 2.1
Plug-in Dimmer Socket Kit
Model No. LW301
EC DECLARATION OF CONFORMITY
Responsible Authority:
LightwaveRF PLC,
Innovation Campus Birmingham
Faraday Wharf
Holt Street
Birmingham
B7 4BB
Tel: +44 (0)121 250 3625
Model Number(s): JSJSLW301
Description: Plug-in Dimmer Kit
Directives this equipment
Complies with: 2006/95/EC The Low Voltage Directive N/A
2004/108/EEC The Electromagnetic Compatibility Directive
1999/5/EC R&TTE Directive
93/68/EEC CE Marking Directive
Standards Applied in order to verify compliance
Safety: BS EN 60730-1: 2011
Health:
R&TTE: EN 301 489-1 V1.9.2: (2011-09), EN 301 489-3 V1.4.1: (2002-08)
EN 300 220-1 V2.1.1: 2006, EN 300 220-2 V2.1.2: 2007
EMC: EN 301 489-1 V1.9.2: (2011-09), EN 301 489-3 V1.4.1: (2002-08),
EN 55022: 2010, EN 61000-3-2: 2006 +A1: 2009 +A2: 2009 Class A,
EN 61000-3-3: 2008, EN61000-4-2: 2009,
EN 61000-4-3: 2006 +A1: 2008 +A2: 2010, EN 61000-4-4: 2012,
EN 61000-4-5: 2006, EN 61000-4-6: 2009, EN 61000-4-11: 2004
For and on behalf of LightwaveRF PLC
----------------------------------------
Name J Shermer
Position Managing Director
How does it work?
How do I get started?
Refer to the setup guide on the following pages
to get going. No specialist knowledge or tools
are required as these sockets are ‘plug and play’;
however, always remember to take care when
dealing with mains electricity.
The Plug-in Dimmer is designed to plug into any
standard 13A socket. It allows any connected
lamp (up to 300W) to be turned on and o and
dimmed using the remote control included in this
pack, or by using a smartphone / tablet
(requires the Lightwave Link).
Help video & further guidance
For additional guidance, and to watch a video
that will help guide you through the installation
process, please visit the support section on
www.lightwaverf.com
Get Started
IMPORTANT: Please retain these instructions for guidance on how to link
Remote Handsets and other LightwaveRF controllers. For additional
guidance please visit the support section on www.lightwaverf.com.
Bank Selector
Manual Button
(on side of
Plug-in).
Press to toggle
Plug-in on/o
LED. Blue
when power is
on / amber
when o
Overview
On/O Buttons
Transmission LED
All O Button
Mood Buttons
Device setup
Lamp Compatibility
Before you begin setting up and using the Plug-in Dimmer, you must ensure
that you have compatible lamps (bulbs). Ensuring the compatibility of your
lamps with LightwaveRF Plug-in
Dimmers will ensure that you get the best
experience from your lighting setup.
LightwaveRF Plug-in Dimmers are compatible with
• Standard mains voltage incandescent & low energy incandescent lighting
(min 40W, max 300W)
• GU10 and equivalent HI spot mains halogen lamps
LightwaveRF Plug-in Dimmers are NOT compatible with
• Wirewound transformers (generally older style)
• Electric motors
• LEDs
• CFLs
• CFL tube arrays
Device setup
Linking the plug-in to LightwaveRF controllers
LightwaveRF plug-ins each have 6unique memory slots which means they
can link with up to 6 seperate LightwaveRF controllers in total.
NOTE: If you are using a smartphone/tablet/PC to control the Plug-in via the
Lightwave Link, this will always count as ONE controller and take up one
memory slot even if you are using multiple smartphones/tablets.
1. On the Plug-in, press and hold
down the manual button until the
LED flashes blue/amber alternately.
The Plug-in is now in linking mode.
2. Using a LightwaveRF controller
(such as the Mood Remote provided),
Smartphone or Web App, press the
button intended to be linked (the ‘on’
button on the Mood Remote); the
LED will flash blue to confirm that the
remote is now linked. If you are using
a LightwaveRF App, please refer to
in-App help for guidance.
Device setup
NOTE: Linking mode lasts for 12 seconds; if no signal is received from a
remote handset during this time then the Plug-in will automatically exit
linking mode without linking the device.
If, when expecting a quick flashing blue LED to confirm pairing, a slow
amber flash is received instead, then the Plug-in memory is FULL and no
further remotes may be linked with it unless one of the existing remotes is
unpaired first (see below).
1. On the Plug-in, press and hold the
Manual button until the LED flashes blue
and amber alternately, and then release it.
The Plug-in is now in linking mode.
2. On the
controller press the button that
you intend to link.
If using the Smartphone
or Web App, press the ‘connect’ button
(the App instructions
will guide you
through this).
The LED will flash blue to
confirm that the remote is now linked.
Unlinking remotes and clearing the Plug-in memory
Removing a single Device:
Device setup
NOTE: Reliable range of operation is around 15 metres indoors and up to
100m outdoors using the Lightwave Link. This figure may vary depending
upon the environment; very thick walls, bodies of water or large metal
objects may interfere with radio range.
If the distance between the transmitter and receiver is too great to achieve
reliable operation, the LightwaveRF Signal Booster may be used in
conjunction with this product to increase the range.
Clearing memory (will remove all linked remotes):
1. Press and hold down the manual
button until the LED flashes blue and
amber alternately, and then release it.
The Plug-in is now in linking mode.
2. On the Plug-in, press and hold down
the manual button again until the LED
flashes purple, then tap (don’t hold) the
Manual button a further time; the LED
will flash amber quickly to confirm that
the memory has been cleared.
Device setup
• Press and release the manual button to
toggle the Plug-in between the o and
on state (amber LED indicator will turn
blue and vice-versa).
NOTE: When turned on, The Plug-in will
dim to the level it was at when turned o.
Manual operation
IMPORTANT: The Plug-in Dimmer Socket will NOT function and the amber
LED will not illuminate unless there is a suitable, working lamp plugged in
to provide a load and form a connected circuit. The lamp must be turned on.
• Plug the LightwaveRF Plug-in Dimmer
Socket into a standard 13A wall socket and
ensure that the wall socket is turned on.
• Plug a working portable lamp into the
Plug-in Dimmer and ensure that it is
turned on. The LED on the Plug-in will
illuminate amber to illustrate that it has
detected a ‘load’ (working lamp).
Manual button
Manual operation
Control with a LightwaveRF
controller or smartphone
• Press the ‘on’ button on the
controller, Smartphone or Web App
once to switch the Plug-in Dimmer on
(LED indicator will illuminate blue).
Hold the button to increase light level.
• Press the ‘o’ button on the
Controller, Smartphone or Web App to
switch the Plug-in Dimmer o (LED
indicator will illuminate amber). Hold
the button to decrease the light level.
Using the Mood Remote
This kit comes with a Mood Remote Control. The Mood Remote can be
linked to one or more plug-in sockets using the method previously
described.
The Mood Remote has 4 independent channels that can be accessed
using the ‘bank selector’ switch. This means that a device/s can be linked
and controlled independently using the on/o buttons on each bank.
Remote operation
Indice
Altri manuali Lightwave Dimmer
