Lindy 38238 Manuale utente
© LINDY Group - FIRST EDITION (October 2022)
4x4 HDMI 4K60 Matrix with Video Wall
Scaling
User Manual English
Benutzerhandbuch Deutsch
Manuel Utilisateur Français
Manuale Italiano
Manual del Usuario Español
No. 38238
lindy.com
User Manual English
! WARNING !
Please read the following safety information carefully and always keep this document with
the product.
Failure to follow these precautions can result in serious injuries or death from electric
shock, fire or damage to the product.
This device works with a high voltage of 230 VAC. Do not connect it to mains supply
voltage system of 100 - 120 VAC –this will cause damage to the unit, fire and can result
in serious injuries or death from electric shock.
Touching the internal components or a damaged cable may cause electric shock, which may result in
death.
To reduce risk of fire, electric shocks or damage:
▪Do not open the product. There are no user serviceable parts inside.
▪Only qualified servicing personnel may carry out any repairs or maintenance.
▪Never use damaged cables.
▪Do not expose the product to water or places of moisture.
▪Do not use this product outdoors it is intended for indoor use only.
▪Do not place the product near direct heat sources. Always place it in a well-ventilated place.
▪Do not place heavy items on the product or the cables.
▪Please ensure any cables are firmly secured and locked in place before inserting into a power socket
Introduction
Thank you for purchasing the 4x4 HDMI 4K60 Matrix with Video Wall Scaling. This product has been
designed to provide trouble free, reliable operation. It benefits from both a LINDY 2-year warranty and free
lifetime technical support. To ensure correct use, please read this manual carefully and retain it for future
reference.
Package Contents
▪4x4 HDMI Matrix
▪Country Specific C13 Power Cables, 2m
▪4 x IR Emitter Cables, 1.5m
▪4 x IR Receiver Cables, 1.5m
▪IR Remote & CR2025 Battery
▪1 x 3-pin Phoenix Connector
▪1 x USB to RS-232 Cable
▪Lindy Manual
Features
▪Supports resolutions up to 3840x2160@60Hz 4:4:4 8bit
▪Seamless switching between devices
▪Video Wall Scaling –create up to a 2x2 or 4x1 vertical video wall
▪Individual IR matrix control
▪EDID Management
▪Controllable output resolution scaling
▪Push button, IR, RS-232, TCP/IP Control
Specification
▪HDMI 2.0 18Gbps
▪HDCP 1.4
▪HDMI Audio Pass-through
▪IR Support: 20-60kHz
▪Housing Material: Metal
User Manual English
▪Operating Temperature: 0°C - 40°C (32°F - 104°F)
▪Storage Temperature: -20°C - 70°C (-4°F - 158°F)
▪Humidity: 10-50% RH (non-condensing)
▪Power Requirements: 100W, 110-240VAC
▪Colour: Black
Connections:
▪Input: 4 x HDMI Type A (Female), 4 x 3-Pin Phoenix
▪Output: 4 x HDMI Type A (Female), 4 x 5-Pin Phoenix, 4 x Mini Toslink (Female)
▪Control: RS-232 (Female), RJ-45 (Female), 8 x IR 3.5mm (Female)
▪Power: IEC C14
Front and Rear Panel Overview
Front Panel
INPUT 1-4: Select between 4 HDMI source devices by pushing the required Input button
OUTPUT 1-4: Select between 4 HDMI displays by pushing the required Output button
LOCK: Press and hold for two seconds to lock or unlock the matrix’s front panel push button control.
When the controls are locked the Lock LED will be illuminated.
ALL: Press ALL then a chosen Input and the Take button consecutively, this will switch the user’s
chosen Input to output on all output displays
RES: Press Res, a chosen output, then Next. Repeatedly pressing Next will allow the userto cycle through
several output resolutions for the selected display. Press Take to select the desired resolution. When Auto
resolution is selected the optimum resolution of the display will be chosen.
EDID: Press EDID, then a chosen Input, then Next. This will allow the user to manage the EDID of the
chosen Input port. The Manual EDID setting is for EDID Management via the Matrix’s control software.
NEXT: Cycles to the next option
SAVE: Press Save and a chosen Output, this will save the current layout of Inputs –Outputs under the
selected Output push button. The maximum number of possible saved layouts is 4.
RECALL: Press Recall and the same chosen Output as above to set the chosen layout from the
previously set 4 options.
CLEAR: Cancel the current command function
TAKE: Set the displayed option
Rear Panel
LAN: Control the unit using TCP/IP Control
RS-232: Control the unit using RS-232 Control
User Manual English
IR OUTPUT/INPUT: These correspond with the Input HDMI to Output HDMI port of the same number for
control from the display side
AUDIO INPUT: These correspond with the Input HDMI port of the same number. Embed analogue audio
via a 3-pin Phoenix Connector
AUDIO OUTPUT: These correspond with the Output HDMI port of the same number. Extract analogue
audio via a 5-pin Phoenix Connector or a Toslink connection
INPUT 1-4: Connect up to 4 source devices
OUTPUT 1-4: Connect up to 4 displays
C13 Power: Connect with included AC Power cord
Operation
IR Remote
This can provide basic switching control over each source and display.
RS-232 & LAN Control
Connect the RS-232 port of the Matrix to a PC via a serial cable, as shown in the following diagram:
For RS-232 Control, the baud rate is 9600. A detailed list of all commands can be found in the download
section of the article on the Lindy website.
For LAN/IP Control, please see the default setting below
PC Software
Please run the latest version of the software from the Download section of your local Lindy website
On entry a password is required:
For Administrator access: 111111
For User access: 000000
User Manual English
Connecting to the Web-GUI
On the default first page, please select UART if using with RS-232 or Network if using a LAN connection.
For RS-232 Control:
To identify IP information:
▪Once connected and UART is selected, select the Find Via UART button on the Matrix Switch page.
This will show the IP information of the matrix. This can also be done via the Network Setting page.
To set IP address:
▪On the Network Setting tab, select Find Via UART to read the current IP address.
▪Modify the IP address type to Static IP or to Auto IP (DHCP). If set to Static IP, the new IP address,
subnet mask and gateway information can be added.
▪Select Save Config to save the configuration
▪Select Find Via UART to confirm the change has been successful
For Network control follow the steps below:
To identify IP address: Once connected and Network is selected, select the Search Device button on the
Matrix Switch page. This will show the IP information of the matrix. This can also be done via the Network
Setting page.
To set IP address:
▪On the Network Setting tab, select Search Device.
▪Select the device to configure.
▪Modify the IP address or address type.
▪Select Save Config to save the configuration
▪A success message should now show. Select Search device again to confirm the change has been
successful.
For direct connection, please follow the instructions below
▪Connect the matrix and PC using Cat.x cable
▪Please ensure the matrix and PC are in the same network segment (The default IP address of the
matrix is 192.168.0.247, and the default network mask of the matrix is 255.255.255.0)
▪Run the control software. Please note: If the IP address of the PC has changed after running the
software please reboot the software.
▪Select Network under CTRL Mode
▪Select Search device
▪Select the matrix to control (Once selected, the software will read the network configuration)
▪Select Disconnected to connect to the matrix
▪Once a successful connection is made, Status will be changed to Connected. If this is selected again
it will disconnect from the matrix.
User Manual English
For connection via a Network switching or routing system please follow the process above with direct
connection to a network switch between the PC and matrix. If the IP address is not obtained automatically
by the software via Automatic (DHCP) mode, please ensure the network switch supports DHCP.
Once connected the user can now progress with controlling the matrix.
Matrix Switch
Switch UI: The user can select this to change the UI from the default
Allset: This provides a shortcut to switch 1 input to all output displays
Recall: Recall a specific matrix routing that has been previously saved
SaveAs: Save current matrix routing.
System Reset: Factory reset the unit.
EDID: Select this button to open the EDID Management page
User Manual English
EDID Management
Read EDID: Select yourchosen output port and select Read
to show the output EDID
Write EDID: Once an EDID has been read, select a chosen
Input port and then Write to change the EDID
Save EDID: Once changed, select Save to save the current
EDID
Manual EDID: 1 Input port at a time can be manually
controlled by the Front Panel
User Manual English
Signal Setting
Audio Select
Auto –If anHDMI input signalis provided, HDMI audio will be passthrough.If a DVIInput signalis provided,
the matrix will rely on the analogue audio input connection for audio.
External –The matrix will use the corresponding analogue audio input connection.
Output Type
The Output Type is pre-configured to support HDCP 1.4
Output Format
The user can select a desired output resolution.
Fine Tune
This setting is reserved for future use
User Manual English
Advanced Switch
This software allows for automatic switching of devices at time intervals.
Select the Output port that requires control. Select CTRL and the desired ports to select multiple outputs.
Select CTRL and then select the desired input ports.
Select the →button to configure the selected inputs ports to the selected output ports.
User Manual English
Please ensure the desired output ports are ticked.
To configure automatic switching
Switch Frequency: The default is 2000milliseconds
Send all outputs combined: All outputs will be un-ticked by default
Un-ticked –Switch all ports one by one
Ticked –Switch all output & the desired input ports at the same time
Please note: If many input ports are selected, this will switch inputs one by one
Wait until others have finished then start next loop: This can be selected when “Send all outputs
combined” is ticked
Un-ticked - When the number of the selected input ports is not the same as selected output ports, the
next loop will automatically start once the final output has finished.
Ticked –All outputs will start a new loop at the same time. When the number of the selected input ports
is not the same as selected output ports, the next loop will automatically start once the final output has
finished.
Stop CMD after one loop: Automatically stops switching once one loop is finished
Select all outputs: Quickly tick/un-tick all output ports
Select Start to begin the automatic switching loop
While in progress, select Stop to instantly stop the loop.
Indice
Lingue:
Altri manuali Lindy Commutatore a matrice
Lindy
Lindy 38148 Manuale utente
Lindy
Lindy 38245 Manuale utente
Lindy
Lindy 38042 Manuale utente
Lindy
Lindy 38247 Manuale utente
Lindy
Lindy 38350 Manuale utente
Lindy
Lindy 38313 Manuale utente
Lindy
Lindy 38044 1.3b Manuale utente
Lindy
Lindy 38088 Manuale utente
Lindy
Lindy 38089 Manuale utente
Lindy
Lindy 38048 Manuale utente
Lindy
Lindy 38152 Manuale utente
Lindy
Lindy 32595 Manuale utente
Lindy
Lindy HDMI 8x8 Matrix Switch 1.3c Manuale utente
Lindy
Lindy 38302 Manuale utente
Lindy
Lindy 38044 Manuale utente
Lindy
Lindy 38153 Manuale utente
Lindy
Lindy 38152 V2 Manuale utente
Lindy
Lindy 38248 Manuale utente
Lindy
Lindy 38248 Manuale utente
Lindy
Lindy 38245 Manuale utente
