Linear HDMI-SW-4X1 Manuale utente
www.linearcorp.com
4X1 Switcher For
1.3
Model # HDMI-SW-4X1
USER MANUAL
ASKING FOR ASSISTANCE
Technical Support:
Telephone (800) 421-1587
(760) 438-7000
Fax (760) 438-7199
Technical Support Hours:
6:30 AM - 4:30 PM PST Monday through Friday.
Email:
Website:
www.linearcorp.com
Notice
Linear LLC reserves the right to make changes in the hardware, packaging
and any accompanying documentation without prior written notice.
© 2008 Linear LLC, All Rights Reserved
TABLE OF CONTENTS
1
2
3
4
5
6
7
8
9
10
Introduction / Operation Notes
Features
Panel Descriptions
Connecting and Operating the 4X1 Switcher For HDMI 1.3
RMT4-IR Installation
IR Code Conicts
RS-232 Serial Control Interface
Wiring Diagram
Specications
Warranty
The Linear 4x1 Switcher for HDMI 1.3 routes high denition video in multiple
resolutions up to 1080p plus multichannel digital audio from any of four sources to
one display. Four HDMI inputs accommodate the simultaneous connection of up to
four high denition video sources, such as satellite systems, Blu-ray and HD-DVD
players. The output sends the high denition audio/video signals to a high denition
display.
How It Works
You simply connect all your sources to the switcher’s HDMI inputs. Then connect
your display to the switcher’s HDMI output. Once the sources, the switcher and the
display are powered and connected, you simply select which source you want to
view using the IR remote, the selector buttons on the front panel, or by the RS-232
serial control interface.
INTRODUCTION
1
OPERATION NOTES
READ THESE NOTES BEFORE INSTALLING
OR OPERATING THE 4X1 SWITCHER FOR HDMI 1.3
• When powering the sources, the display needs to point to the source input.
• The 4X1 Switcher For HDMI 1.3 works with all DVI* and HDMI displays.
• The 4X1 Switcher For HDMI 1.3 is HDCP compliant.
• The 4X1 Switcher For HDMI 1.3 is HDMI 1.3a compliant.
NOTE *Using a DVI to HDMI adapter
FEATURES
2
Features
Switches easily between any four HDMI sources•
Supports resolutions up to 1080p, 2K and 1920 x 1200•
Inputs can be switched with the IR remote control, the selector buttons on the• front of the unit, or by RS-232 serial control interface
Extends the range of HDMI compliant devices by equalizing and re-clocking the• HDMI signal control interface
HDMI 1.3/HDCP compliant•
Includes:
(1) 4X1 Switcher For HDMI 1.3
(4) 6’ HDMI cables (M-M)
(1) 5V DC Power Supply
(1) RMT4-IR Remote Control
(1) User’s Manual
3
PANEL DESCRIPTIONS
IR Eye Input LED
Indicator
FRONT
BACK
DIP SWITCH LOCATION
Input 1
Selector Input 2
Selector
Input 3
Selector Input 4
Selector
Power LED
Indicator
RS-232
Control Port IR Eye
Extension Port
Input 4Input 3Input 2Input 1
5V DC Power
Input
4 Bank Dip
Switch
CONNECTING AND OPERATING THE 4X1 SWITCHER FOR HDMI 1.3
SWITCHING INPUTS ON THE 4X1 SWITCHER FOR HDMI 1.3
How to Connect the 4X1 Switcher For HDMI 1.3 to your devices
Connect the HDMI sources to the 4X1 Switcher for HDMI 1.3 input ports using the
supplied HDMI cables.
Connect the display (monitor or projector) to the 4X1 Switcher for HDMI 1.3 output
port using a user supplied cable.
Plug the 5V DC power supply into the 4X1 Switcher for HDMI 1.3.
Input switching on the 4X1 Switcher for HDMI 1.3 can be done using either the supplied IR
remote control, the selector buttons on the front panel, or by RS-232 serial control interface.
IR Remote
The supplied IR remote control is labeled with four buttons that correspond to the four inputs
on the 4X1 Switcher for HDMI 1.3. Pressing any of the four buttons will switch the 4X1
Switcher for HDMI 1.3 to that numbered input.
Selector Buttons
There are selector buttons on the front of the 4X1 Switcher for HDMI 1.3 for each of the
four inputs. Pressing any of these buttons will switch the 4X1 Switcher for HDMI 1.3 to the
corresponding numbered input.
RS-232 Serial Control Interface
Please see page 7 for more information on the RS-232 serial control interface.
1.
2.
3.
4
RMT-4IR INSTALLATION
1. Remove battery cover from the back of the RMT-4IR remote.
2. Verify that dip switches 1 & 2 are in the down (OFF) position. (See page 6)
3. Insert the battery, hold the battery so that you can see the positive side facing up.
The side that is not marked must be facing down.
4. Test the RMT-4IR remote by pressing ONLY one button at a time. The indicator
light on the remote will ash once each time you press a button.
WARNING:
Do not press multiple buttons simultaneously and do NOT press buttons rapidly.
These actions will cause the remote to reset and steps 1-4 will have to be repeated.
Note: The RMT-4IR ships with two batteries. Only one battery is required for
operation, the other battery is complimentary.
5
The optional IR extender allows you to
relocate your HDMI Switcher and still retain IR
control. Linear part# IR-EXTENDER
6
IR CODE CONFIGURATION
4X1 Switcher For HDMI 1.3
Remote Channel 1:
Default
Remote Channel 4:
Remote
Remote Channel 1:
Default
1 2
Remote Channel 2:
1 2
Remote Channel 3:
1 2
Remote Channel 4:
1 2
How to Resolve IR Code Conicts
In the event that IR commands from other remote controls conict with the supplied
RMT-4IR remote control, changing the remote channel will alleviate this issue. The
RMT-4IR remote control and the 4X1 Switcher for HDMI 1.3 have DIP SWITCHES
for conguring the remote channel that both units use to communicate. These
settings must match each other for proper operation. The 2 DIP SWITCH bank on
the RMT-4IR is located underneath the battery cover. The 4 DIP SWITCH bank for
the 4X1 Switcher for HDMI 1.3 is located on the underside of the unit beneath a
black piece of metallic tape. DIP SWITCH 1 and 2 on the RMT-4IR correspond to
*DIP SWITCH 1 and 2 on the 4X1 Switcher for HDMI 1.3.
NOTE: *DIP SWITCHES 3 and 4 are not used on the 4X1 Switcher for HDMI 1.3.
1
1
2
2
3
3
4
4
Remote Channel 3:
1234
Remote Channel 2:
1234
Indice
