liniLED PCB Photon 1200 Manuale utente
LED strip manual
liniLED® Top Photon 1200
24
V DC
UV RESISTANT
GLOW WIRE
850 °C
FROST
RESISTANT
F
CLEANING AGENTS
RESISTANT
IP40/IP68 SWIMMING POOL
ENVIRONMENT
IK08 SWIMMING POOL
SUBMERSIBLE
MAC
ADAM
2
S D C M
BEND RADIUS
R
30 mm CRI
80+
5
System
RoHS SEA WATER
RESISTANT
V100920
liniLED® Top Photon 1200
Technical notes 4
Top Photon 1200 - Product drawings 5
Product information 5
Product specications 5
Cable selection 6
Area advice 7
Product care and handling 8
Cutting instructions 9
Solder 11
Connect IP40 13
Uninstalling the connector 15
Welded connector 16
Power supply 17
Symbols 18
4LED strip manual | liniLED® Top Photon 1200
Read the instructions and safety precautions before installation, usage and storage of the products to secure safety of the user and reliability of the product.
- Hand over the instructions to the end user and those responsible for installation and usage.
- Triolight B.V. cannot be held responsible for improper handling, product installation, usage or storage.
Handling
- Handle with care.
- The product may not be modied or converted otherwise than prescribed.
- Products are transported in proper packaging. Products should remain packed until installation.
- Take ESD (Electrostatic Discharge) protection measures when handling liniLED® products.
- The products and their components may not be exposed to mechanical, static loads and other tension/compression other than from the product itself.
Installation
- Attention: The power has to be switched o the main power supply or the connection before installation. Not doing so may damage the product.
- Use a suitable LED power supply/driver: 24 V DC constant voltage. Do not drive the product on other voltages than described in their datasheet/products
specications.
- Installation has to be done by a certied professional with knowledge of electrical circuits or a specialised maintenance person known with valid directives.
- General and local construction-, safety- and installation regulations should be respected.
- Use only supplied parts, accessories and required tools as prescribed in the installation manual to guarantee a safe installation and use of the product.
- Products may solely be installed in the areas according to their prescribed IP-rating, IK-rating, temperature range and chemical resistances.
- The LED strip should be installed on an adequate cooling body for proper heat dissipation to ensure smooth operation and long lifetime.
- Do not fasten anything to the product. The same applies when hanging.
- Do not install the product in the following cases:
- Damage is visible on the product or its cables.
- The inside of the product is moistened or dirty.
- The product or its cables have been modied. This could lead to an electrical shock or a short circuit may occur.
- Children may not play unsupervised with electrical products as they cannot judge the dangers in dealing with electrical circuits correctly.
- Use proper mounting surfaces when installing in environments with large variations in temperature and operating lengths more than 2 metres. This should
absorb the stress of any dierence in expansion.
Operation and use
Solely use the product when it’s working correctly. If not, switch the power o immediately and ask an electrical specialist for advice in the following cases:
- Damage is visible on the product and/or the product does not function.
- The product is overheating and/or smoke or steam rises from the product.
- Crackling sounds are noticeable.
Repairs on the installation may only be performed by qualied electricians. Product repairs may solely be done by Triolight B.V.
Cleaning and maintenance
- Attention: Disconnect the power before maintenance and cleaning.
- Dust and dirt accumulated over time should be removed from the light emitting surface to assure optimal functioning of the product.
- Paints, solvents and corrosive cleaning chemicals may not contact and thus aect the product.
Environment and waste
- Exterior decorative lighting should only be used after sunset.
- This product may not be treated as household waste. Dispose of the material through the waste recycling of electrical and electronic equipment.
Warranty
This product comes with a 2 year warranty. Warranty void if:
- The installation guide has not been consulted (installation mistake).
- The installation is not done by a certied installer.
- Local rules and guidelines are not respected.
- The invoice cannot be shown and/or has been altered.
- Damage is caused by negligence, abnormal use or improper handling, use, maintenance and/or cleaning of the product.
Technical notes
5LED strip manual | liniLED® Top Photon 1200
The liniLED® LED strip Top Photon 1200 - White (IP40/IP67*) is a high quality, exible LED strip with an outstanding ecacy. The combination of high quality,
exceptional exibility and a unique co-extrusion technology, allow for an endless range of indoor and outdoor applications. The liniLED® LED strip Top Photon
is available in various white colours.
* Connect the Top LED strips with the liniLED® Top Connector Sets (1 m 11200 or 5 m 11201). Use the liniLED® Top Extension Cord (11208) to extend.
For IP67 usage, combine with the liniLED® Top IP67 Kit (11490) and the liniLED® Top IP67 Extension Kit (11491).
LED strip top view
LED strip front view
6
12
100
12
14.3
Product information
Product specications
Colour LED/m V DC W/m lm/m Temp ˚C Max. Length B70/L50
2000K 70 24 10.6 811 -30...559 m > 60.000 h
2400K 70 24 10.6 958 -30...559 m > 60.000 h
2700K 70 24 8.9 997 -30...559 m > 60.000 h
3000K 70 24 8.9 1023 -30...559 m > 60.000 h
4000K 70 24 8.1 1008 -30...559 m > 60.000 h
6500K 70 24 8.1 1003 -30...559 m > 60.000 h
Max. connection length between -30 °C and -20 °C is 6.3 metres.
Top Photon 1200 - Product drawings
6LED strip manual | liniLED® Top Photon 1200
1. Colour temperature Photon 1200
2. LED strip length 1 m 2 m 5 m 9 m
3. Voltage 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC
4. Cable cross section 0.50 mm - 0.035 Ω/m 36.9 m 72.1 m 17.8 m 35.4 m 6.3 m 13.4 m 2.9 m 6.8 m
0.75 mm - 0.023 Ω/m 55.6 m 108.5 m 26.8 m 53.3 m 9.5 m 20.1 m 4.4 m 10.3 m
1.00 mm - 0.018 Ω/m 73.9 m 144.3 m 35.6 m 70.8 m 12.7 m 26.8 m 5.9 m 13.7 m
1.50 mm - 0.012 Ω/m 111.2 m 217.1 m 53.6 m 106.6 m 19.1 m 40.3 m 8.9 m 20.6 m
2.50 mm - 0.007 Ω/m 185.1 m 361.4 m 89.3 m 177.4 m 31.8 m 67.1 m 14.8 m 34.4 m
Note: Calculations are based on a standard connector with 1 metre cable (0.5 mm).
1= Select colour temperature.
2 = Select LED strip length.
3= Select output voltage.
4= Select cable cross section.
Result = Maximum cable length based
on the cable thickness and power supply
voltage.
Cable selection
-+
Top/Side Connector (1000 mm)
1
2
3
4
Result
Cable selection
7LED strip manual | liniLED® Top Photon 1200
Depending on the installation area of the liniLED® LED strip we oer a range of IP40, IP67 and IP68 solutions to cope with external factors. Below the dierent
connectors are displayed for use in dierent environments. See corresponding pages or individual product manual for further instructions.
Indoor environment | (IP20)
Solder
Indoor environment | (IP40) | liniLED® Top Connector set.
Product code: 11200 (1 m), 11201 (5 m)
Wet environment | (IP67) | liniLED® Top IP67 Kit
Product code: 11490
See Manual liniLED® Top IP67 Kit for installation instructions.
Submersible, chlorine resistant | (IP68) | Welded Connector
Product code: 12296 1m
12297 5m
The connector is pre-assembled to the LED strip.
Area advice
8LED strip manual | liniLED® Top Photon 1200
Product care and handling
30 mm
30 mm
Maximum bending radius is 30 mm. Solely bend up or downward. Do not compress or stretch the LED strip.
Do not bend the LED strip sidewards. Do not twist the LED strip.
The LED strip has to be unreeled on a horizontal surface at the time of installation. Do not unreel the spool of LED strip before installation.
9LED strip manual | liniLED® Top Photon 1200
Work in an ESD protected environment. Make use of an anti-static
strap.
Turn o the power before cutting the LED strip.
Side view | Make sure the cut is vertical as illustraded in the image
above.
Top view | Make sure the cut is vertical as illustraded in the image
above.
Top view | Only cut on the dotted lines to prevent damaging the LED
strip.
Dispose of the unnecessary material through waste recycling of
electrical and electronic equipment.
Cutting instructions
5
3
2
4
6
1
10 LED strip manual | liniLED® Top Photon 1200
Place the liniLED® LED strip on the base of the cutting tool. Not doing so may result in a deformed LED strip.
Cutting instructions
7
Indice
