LinMot DM01-23-FS Manuale utente

NTI AG / LinMot Doc-No. 0185-0168-E_1V3_IG_Force_Sensor_Modules_DM01-FS

Installation Guide

Force Sensor Modules

DM01-23-FS / DM01-37-FS / DM01-48-FS

Installation Guide Force Sensor Modules EN 
Page 2 / 25 DM01-23-FS / DM01-37-FS / DM01-48-FS NTI AG / LinMot 
Content 
1General Information ................................................................................................................................. 4 
1 Introduction........................................................................................................................................ 4 
2 Explanation of Symbols..................................................................................................................... 4 
3 Qualified Personnel ........................................................................................................................... 4 
4 Liability............................................................................................................................................... 4 
5 Copyright............................................................................................................................................ 4 
2Safety Instructions................................................................................................................................... 5 
3Installation Instructions........................................................................................................................... 7 
1 Operating Conditions......................................................................................................................... 7 
2 Assembling Instruction Force Sensor DM01-23-FS.......................................................................... 7 
3 Assembling Instruction Force Sensor DM01-37-FS.......................................................................... 8 
4 Assembling Instruction Force Sensor DM01-48-FS.......................................................................... 9 
5 Adjusting the Length of the Cable Conduit...................................................................................... 10 
5.1 DM01-23...................................................................................................................................... 10 
5.2 DM01-37...................................................................................................................................... 10 
5.3 DM01-48x150.............................................................................................................................. 11 
5.4 DM01-48x240.............................................................................................................................. 11 
6 Material Data ................................................................................................................................... 11 
4Electrical Connection............................................................................................................................. 11 
1 Sensor Cable................................................................................................................................... 11 
1.1 Technical Data............................................................................................................................. 11 
2 Pin Assignment Sensor Cable......................................................................................................... 12 
3 Force Sensor Module Wiring........................................................................................................... 12 
3.1 Connection to C11x0 and C12xx Servo Drives........................................................................... 12 
3.2 Connection to C1252 Servo Drive............................................................................................... 13 
5Commissioning....................................................................................................................................... 13 
1 Initial Commissioning of the Force Sensor...................................................................................... 13 
1.1 Technology Function Force Control" Software Package............................................................. 13 
1.2 Setting the Parameters for Force Control at C12x0.................................................................... 13 
1.3 Initial Testing of a Force Sensor.................................................................................................. 14 
2 Special LinMot-Talk Functions......................................................................................................... 15 
2.1 Tare Function............................................................................................................................... 15 
2.2 Speed limiter function.................................................................................................................. 16 
6Accessories ............................................................................................................................................ 17 
1 Extension Cables............................................................................................................................. 17 
1.1 Extension Cable for Connection to C11x0 and C12xx Servo Drives .......................................... 17 
1.2 Extension Cable for Connection to Servo Drive C1252 .............................................................. 17 
7Maintenance and Test Instructions...................................................................................................... 17 
1 Maintenance.................................................................................................................................... 17 
2 Cleaning........................................................................................................................................... 18 
3 Lubrication ....................................................................................................................................... 18 
4 Calibration........................................................................................................................................ 18 

Installation Guide Force Sensor Modules EN

NTI AG / LinMot DM01-23-FS / DM01-37-FS / DM01-48-FS Page 3 / 25

8Transport and storage........................................................................................................................... 18

9Dimensions............................................................................................................................................. 19

9.1 Force Sensor Module DM01-23-FS................................................................................................. 19

9.2 Force Sensor Module DM01-37-FS................................................................................................. 21

9.3 Force Sensor Module DM01-48-FS................................................................................................. 22

10 EU Declaration of Conformity CE-Marking.......................................................................................... 23

11 UK Declaration of Conformity UKCA-Marking .................................................................................... 24

Installation Guide Force Sensor Modules EN

Page 4 / 25 DM01-23-FS / DM01-37-FS / DM01-48-FS NTI AG / LinMot

1 General Information

1.1 Introduction

This manual includes instructions for the assembly, installation, maintenance, transport, and storage of

DM01 force sensor modules. The document is intended for electricians, mechanics, service technicians, and

warehouse staff.

Read this manual before using the product and observe the general safety instructions and those in the

relevant section at all times.

Keep these operating instructions in an accessible place and make them available to the personnel

assigned.

1.2 Explanation of Symbols

Triangular warning signs warn of danger.

Round command symbols tell what to do.

1.3 Qualified Personnel

All work such as installation, commissioning, operation and service of the product may only be carried out by

qualified personnel.

The personnel must have the necessary qualifications for the corresponding activity and be familiar with the

installation, commissioning, operation and service of the product. The manual and in particular the safety

instructions must be carefully read, understood and observed.

1.4 Liability

NTI AG (as manufacturer of LinMot and MagSpring products) excludes all liability for damages and

expenses caused by incorrect use of the products. This also applies to false applications, which are caused

by NTI AG's own data and notes, for example in the course of sales, support or application activities. It is the

responsibility of the user to check the data and information provided by NTI AG for correct applicability in

terms of safety. In addition, the entire responsibility for safety-related product functionality lies exclusively

with the user.Product warranties are void if products are used with stators, sliders, servo drives or cables not

manufactured by NTI AG unless such use was specifically approved by NTI AG.

NTI AG’s warranty is limited to repair or replacement as stated in our standard warranty policy as described

in our "terms and conditions" previously supplied to the purchaser of our equipment (please request copy of

same if not otherwise available). Further reference is made to our general terms and conditions.

1.5 Copyright

This work is protected by copyright.

Under the copyright laws, this publication may not be reproduced or transmitted in any form, electronic or

mechanical, including photocopying, recording, microfilm, storing in an information retrieval system, not even

for training purposes, or translating, in whole or in part, without the prior written consent of NTI AG.

LinMot® and MagSpring® are registered trademarks of NTI AG.

Installation Guide Force Sensor Modules EN

NTI AG / LinMot DM01-23-FS / DM01-37-FS / DM01-48-FS Page 5 / 25

2 Safety Instructions

Contusions

Sliders contain neodynium magnets and have a strong attractive force.

Careless handling could cause fingers or skin to become pinched between two sliders.

This may lead to contusions, bruises, and bone fractures.

When handling sliders, wear thick protective gloves and keep a minimum distance between

sliders. Refer to the "Minimum distance from slider" section for minimum distance.

To reduce the risk of injury, never more than one slider should be held or transported by the

same person without packaging.

Pacemaker / Implanted Heart Defibrillator

Sliders could affect the functioning of pacemakers and implanted heart defibrillators. For the

duration of a strong approach to a magnetic field, these devices switch into test mode and

will not function properly.

•If you wear one of those devices keep the following minimum distances between the

pacemaker / defibrillator and slider:

- Min. 250 mm (10ʺ) for slider Ø 27 mm and 28 mm (PL01-27 / 28 / PL10-28)

- Min. 150 mm (6ʺ) for slider Ø 19 mm and 20 mm (PL01-19 / 20)

- Min. 100 mm (4ʺ) for slider Ø 12 mm (PL01-12)

•Inform others who wear these devices to comply with these minimum distances!

Caution - Risk of Electric Shock !

Before working, make sure that there are no high voltages.

Fast-moving Machine Parts

The sliders of LinMot linear motors are fast-moving machine parts. All necessary

precautions must be taken to prevent persons approaching the moving elements during

operation (provide covers, guards, etc.).

Automatic Restart

The motors can start automatically under certain cricumstances!

If necessary, a corresponding warning symbol must be provided and protection against

entering the hazardous area or a suitable safe electronic disconnection must be provided!

Risk of Injury due to a Defect or Fault

For areas where a defect or fault can result in substantial property damage or even serious

personal injury, additional external precautions must be taken or devices must be installed

to ensure safe operation even if a defect or fault occurs (eg. suitable safe electronic

disconnection, mechanical interlocks, barriers, etc.).

Magnetic Field

Magnets integrated in the sliders produce a strong magnetic field. They could damage TVs,

laptops, computer hard drives, credit and ATM cards, data storage media, mechanical

watches, hearing aids, and speakers.

•Keep magnets away from devices and objects that could be damaged by strong

magnetic fields.

•For the above mentioned objects, keep a minimum distance as described in the

"Pacemaker / implanted defibrillator" section.

•For non-anti-magnetic watches, keep the double minimum distance.

Installation Guide Force Sensor Modules EN

Page 6 / 25 DM01-23-FS / DM01-37-FS / DM01-48-FS NTI AG / LinMot

Combustibility

When machining magnets, the drilling dust could easily ignite.

Machining the sliders and the magnets they contain is not permitted.

Burn Hazard

During operation the slider can become hotter than 100 °C, which can cause burns if

touched. All necessary precautions (e.g. covers, casing, etc.) must be taken to prevent

contact with persons in the vicinity of the slider during operation.

Grounding

All metal parts that are exposed to contact during any user operation or servicing and likely

to become energized shall be reliably connected to the means for grounding.

Mechanical Handling

Neodymium magnets are brittle and heat-sensitive.

Machining the sliders and the magnets they contain is not permitted.

•Colliding magnets could crack. Sharp splinters could be catapulted for several meters

and cause eye injury.

•By machining the sliders, heat would result which demagnetizes the magnets.

Slider

Linear motor sliders consist of a high-precision, thin-walled stainless steel tube in which the

neodymium magnets are housed. The LinMot sliders should be handled with care.

Avoid contact with other sliders or iron parts as this can damage the magnets and the slider

surface. Do not grip the sliders with pliers, as this can also damage the surface. Do not use

sliders which are already damaged on the surface (scratches, deformation, etc.). This can

cause further damage to the stator.

Effects on People

According to the current level of knowledge, magnetic fields of permanent magnets do not

have a measurable positive or negative effect on people. It is unlikely that permanent

magnets constitute a health risk, but it cannot be ruled out entirely.

•For your own safety, avoid constant contact with magnets.

•Store large magnets at least one meter away from your body.

Temperature Resistance

Keep slider away from unshielded flame or heat.

Temperature above 120°C will cause demagnetization.

Installation Guide Force Sensor Modules EN

NTI AG / LinMot DM01-23-FS / DM01-37-FS / DM01-48-FS Page 7 / 25

3 Installation Instructions

3.1 Operating Conditions

•The ambient temperature limit is: 0 °C...80 °C (reduced accuracy)

•The nominal service temperature is: 5 °C...45 °C

•Max. Installation altitude: The

maximum installation altitude is 4,000 m a.s.l.

Above 1,000 m, a derating of

1 °C per 100 m must be taken into account for

air cooling.

3.2 Assembling Instruction Force Sensor DM01-23-FS

Be sure to observe the safety instructions in chapter 2 during assembly!

1. Set mounting side

The force sensor module can be mounted on

either side of the linear module.

Due to the mechanical connection of

the slider, it is recommended to mount

the force sensor on the connector side

of the linear module. On this side, the

force is applied directly via a fixed

bearing.

2. Mount force sensor module

Apply Loctite 243 threadlocker to the threaded

holes of the force sensor module.

Then fix the module to the front plate of the

linear module with the four screws.

Tightening torque: 2.6 Nm

The measuring amplifier box can be placed

externally in the machine. The IP protection

class of the amplifier is IP63.

Installation Guide Force Sensor Modules EN

Page 8 / 25 DM01-23-FS / DM01-37-FS / DM01-48-FS NTI AG / LinMot

3. Wiring the force sensor module

The sensor cable is guided in a cable conduit.

The cable conduit can be shortened as required

(see chapter 3.5). For mounting, 2 brackets are

supplied which can be mounted on the DM01

linear module (see illustration). A drive-side

open-end extension cable is recommended for

connecting the force sensor module to servo

drives of the C11x0 and C12xx series (see

chapter Accessories). The wiring diagram is

shown in chapter 4.3.

Only connect or disconnect the sensor

cable when there is no voltage at the

servo drive!

3.3 Assembling Instruction Force Sensor DM01-37-FS

Be sure to observe the safety instructions in chapter 2 during assembly!

1. Set mounting side

The force sensor module can be mounted on

either side of the linear module.

Due to the mechanical connection of

the slider, it is recommended to mount

the force sensor on the connector side

of the linear module. On this side, the

force is applied directly via a fixed

bearing.

2. Mount force sensor module

Apply Loctite 243 threadlocker to the threaded

holes of the force sensor module.

Then fix the module to the front plate of the

linear module with the four screws.

Tightening torque: 8.6 Nm

Installation Guide Force Sensor Modules EN

NTI AG / LinMot DM01-23-FS / DM01-37-FS / DM01-48-FS Page 9 / 25

3. Wiring the force sensor module

The sensor cable is guided in a cable conduit.

The cable conduit can be shortened as required

(see chapter 3.5). For mounting, 2 brackets are

supplied which can be mounted on the DM01

linear module (see illustration). A drive-side

open-end extension cable is recommended for

connecting the force sensor module to servo

drives of the C11x0 and C12xx series (see

chapter Accessories). The wiring diagram is

shown in chapter 4.3.

Only connect or disconnect the sensor

cable when there is no voltage at the

servo drive!

3.4 Assembling Instruction Force Sensor DM01-48-FS

Be sure to observe the safety instructions in chapter 2 during assembly!

1. Dismantle cover

2. Set mounting side

The force sensor module can be mounted on

either side of the linear module.

Due to the mechanical connection of

the slider, it is recommended to mount

the force sensor on the connector side

of the linear module. On this side, the

force is applied directly via a fixed

bearing.

Installation Guide Force Sensor Modules EN

Page 10 / 25 DM01-23-FS / DM01-37-FS / DM01-48-FS NTI AG / LinMot

3. Mount force sensor module

Apply Loctite 243 threadlocker to the threaded

holes of the force sensor module.

Then fix the module to the front plate of the

linear module with the four screws.

Tightening torque: 8.6 Nm

Finally, refit the cover.

4. Wiring the force sensor module

The sensor cable is guided in a cable conduit.

The cable conduit can be shortened as required

(see chapter 3.5). For mounting, 2 brackets are

supplied which can be mounted on the DM01

linear module (see illustration). A drive-side

open-end extension cable is recommended for

connecting the force sensor module to servo

drives of the C11x0 and C12xx series (see

chapter Accessories). The wiring diagram is

shown in chapter 4.3.

Only connect or disconnect the sensor

cable when there is no voltage at the

servo drive!

3.5 Adjusting the Length of the Cable Conduit

All force sensors are delivered with a ready-mounted cable conduit. It is recommended that this is shortened

to an appropriate length. This length is based on the stroke and is measured from the beginning of bracket 1

to the end of bracket 2.

3.5.1 DM01-23

Stroke [mm]

100

160

220

290

350

Recommended length

of the cable conduit

[mm]

385

415

475

535

605

665

3.5.2 DM01-37

Stroke [mm]

195

295

395

495

595

Recommended length

of the cable conduit

[mm]

505

605

705

805

905

1005

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali LinMot Sensore di sicurezza

LinMot

LinMot DM01-48-FS25 Manuale utente

Manuali Sensore di sicurezza popolari di altre marche

THORLABS

THORLABS PDA10JT Manuale utente

Waeco

Waeco UV-DETECT Manuale utente

Intermatic

Intermatic IOS-DSIMF Manuale utente

urmet domus

urmet domus 1083 Manuale utente

Siemens

Siemens AZL66 Series Manuale utente

BTI

BTI Profiline Multi Finder Manuale utente

Challenger

Challenger SL01 Manuale utente

DMP Electronics

DMP Electronics 1122INT Manuale utente

Rielta

Rielta Ladoga MK-RK Manuale utente

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuale utente

Bosch

Bosch DS835 Manuale utente

DBI SALA

DBI SALA EZ Stop Manuale dell'operatore

Lamptime

Lamptime ST05C Manuale utente

Ubiquiti

Ubiquiti MFI-MSC Manuale utente

Subsite

Subsite 910R Istruzioni per l'installazione

Satel

Satel OPAL Pro Manuale utente

Aleph

Aleph XC-1XTEU Manuale utente

Pima

Pima LARIS QUAD Manuale utente