Linsar LSINS20 Manuale utente
Installation Guide
MODEL: LSINS20
TV Install Kit
2
Welcome
Fixing aTV to a wall mount requires specialist knowledge. We assume no liability for any injury or material
damage incurred due to incorrect assembly or use. Make sure to follow all instructions and if you require
professional advice, please consult a relevant tradesperson.
WARNING
Congratulations on choosing to buy a Linsar product.
By doing so you now have the assurance and peace of mind that comes with purchasing a product made by one of the
leading manufacturers.
All products brought to you by Linsar are manufactured to the highest standards of performance and safety and, as part of
our philosophy of customer service and satisfaction, are backed by a comprehensive 1Year Warranty.
We hope you will enjoy using your purchase for many years to come.
3
Contents
Welcome 2
Unpack and Prepare 4
What's in the box 4
Parts List 5
Product Overview 5
Installation Pack (Assembly Hardware) 6
Installation 7
Installing the Bracket 7
Preparation (for a Brick or Concrete Wall) 8
Preparation (for a Wood Stud Wall) 10
Attaching the Monitor Brackets to the TV 12
Securing the TV 13
Installing the Brush Wall Plate 14
Specications 16
Compliance and Responsible Disposal 17
4 | UNPACK AND PREPARE
Unpack and Prepare
What's in the box
Before setting up your new product, check you have everything:
A. TV Wall Mount
B. Screen Cleaning Kit
C. Brush Wall Plate Case (2)
D. Brush Wall Plate (2)
E. Brush Wall Plate Screw (4)
F. C Clip Wall Bracket (2)
G. C Clip Wall Bracket Screw (4)
H. 3M HDMI Cable
I. 3M Antenna Cable
J. Installation Pack (see page 6 for information)
K. Installation Guide
L. Warranty Certificate
M. General Safety Warnings
A
B
C
H
G
I
K
L M
x 2 x 2 x 2
J
F
E
D
PARTS LIST| 5
Parts List
Wall Plate
TV Mounting
Bracket
Product Overview
• Suitable forTVs sized up to
86", weighing up to 60kg
and supporting VESA 600 x
400mm Max.
• Low profile, extending only
30mm (approx.) from the
wall.
6 | PARTS LIST
Installation Pack (Assembly Hardware)
The illustration below shows the contents of the installation pack.These are the parts that you will
need to assemble this wall mount. Some parts are not shown at the same scale.
(G)
Self-Tapping Screw
ST8 x 50mm
(6pcs)
(H)
Masonry Plug
10 x 50mm
(6pcs)
(I)
Flat Washer
M5-M6-M8
(4pcs)
(K)
Plastic Spacer
D8 x 5mm
(8pcs)
(J)
Washer
ø 20 x ø 8.51 x 1.6mm
(6pcs)
(A)
Bolt
M5 x 16mm
(4pcs)
(B)
Bolt
M5 x 25mm
(4pcs)
(C)
Bolt
M6 x 16mm
(4pcs)
(D)
Bolt
M6 x 25mm
(4pcs)
(E)
Bolt
M8 x 16mm
(4pcs)
(F)
Bolt
M8 x 25mm
(4pcs)
A B C D E F G H I J K
INSTALLATION | 7
Installing the Bracket
Tools Required:To complete the following steps you will need:
Installation
A. Pencil
B. Phillips head Screwdriver
C. Stud Detector
D. MeasuringTape
E. Hammer
F. Power Drill
G. Mansory Bit (10mm)
H. Drill Bit (6mm)
Make sure you read and understand all instructions. Handle and use all materials strictly according to the instructions. If
you do not understand these directions, or have any questions in relation to the safety of the installation, we recommend
you contact a qualified professional.
Installation steps:
1Preparation
2Drilling the holes
3Attaching to the wall
4Attaching the Monitor Brackets to theTV
5Securing theTV
TIP: Installation of the Wall Mount will be easier with two people.
WARNING: Be sure to choose a structurally sound wall area that is strong enough to hold the weight of theTV as well as
the wall mount. Mount the wall plate far away from any water source and direct sunlight.
WARNING: DO NOT attach the wall mount to a hollow wall or decorative cardboard.
A B
F
D
G H
E
C
8 | INSTALLATION
Using the wall base plate as a template, mark four holes in locations as shown above.
NOTE: Ensure that you align the bracket so that the spirit level is flat and even.
Preparation (for a Brick or Concrete Wall)
1A
INSTALLATION | 9
Attaching to the Wall 3A
Hold the wall plate against the wall and align the
holes in the plate to the holes drilled into the wall.
Screw the wall plate to the wall with the self-tapping
screws (G): insert them through the washers (J) into
each masonry plug (H) in the wall and then tighten
the screws.
Drilling the holes
On the marked holes, drill holes of 50mm
depth into the concrete or brick wall.
Wedge the masonry plugs (H) into the holes,
gently tap each plug with a hammer until they
are flush with the wall as illustrated on the left.
WARNING: Do not drill into mortar joints.
[J] [G]
2A
[H]
10 | INSTALLATION
Use a stud detector to locate the centre of the framing studs.
NOTE: When you are installing the wall mount to a wood stud wall,
consult your builder for advice.The wall must be strong enough for
the weight of the wall mount and theTV.
Preparation (for a Wood Stud Wall)
1B
WARNING:You must spread
the wall plate across two studs.
Mark six holes in the locations as shown above. Use the wall base plate as a template.
Indice
