Lionel Missile Launch Set Manuale utente

Lionel

Missile Launch Set

Owner’s Manual

featuring

72-1788-250

4/02

CAUTION: Use only with Lionel-approved missiles.

Spring mechanisms require Adult supervision.

Ages 14 and Up.

Congratulations on your purchase of the

Lionel Missile Launch Set! This classic

set is lead by the #44 Missile Launcher

Locomotive, now capable of firing one

missile at a time with TrainMaster

Command Control! A #6823 Flatcar with

missiles and cradles, a #3419 Helicopter

Launch Car, a #6844 Flatcar with missiles,

and a #6814 Stretcher Caboose follow the

locomotive to support the action. The

Missile Launch Set also features an exciting

target—the #943 Exploding Ammunition

Dump.

Congratulations!

The following Lionel marks may be used throughout this instruction manual and are protected under law. All rights

reserved.

Lionel®, TrainMaster®, Odyssey®, RailSounds™, CrewTalk™, TowerCom™, DynaChuff™, StationSounds™,

Pullmor®, ElectroCoupler™, Magne-Traction®, CAB-1 Remote Controller®, Powermaster®, Lionel ZW®, ZW®

Missile Launcher Locomotive features

•TrainMaster Command Control

equipped

•Powerful Pullmor motor

•ElectroCoupler at the rear of the

locomotive

•Magne-Traction track gripping

system

•Operating headlights

•Operating red light on roof

•Four firing missiles

Rolling stock features

•Removable missiles on the missile

flatcars

•Die-cast metal sprung trucks

•Launching helicopter on the #3419

Helicopter Launch Car (Remote-

Control Track section required,

available separately)

Table of contents

Transformer operations

Running your Missile Launcher Locomotive with a Lionel transformer 4

Locking your Missile Launcher Locomotive into a single operational state 5

Using your Missile Launcher Locomotive’s ElectroCouplers in the

non-Command environment 6

Firing your locomotive’s missiles in the non-Command environment 7

TrainMaster Command operations

The CommandControl environment 8

Running your Missile Launcher Locomotive in the TrainMasterCommand environment 9

CAB-1 commands for your Missile Launcher Locomotive 9

CAB-1 numeric keypad commands for your Missile Launcher Locomotive 10

Tuning your Missile Launcher Locomotive’s performance 10

Assigning your Missile Launcher Locomotive a new ID# 11

Reprogramming the Command reverse unit to restore features 12

Maintaining and servicing your Missile Launcher Locomotive

Lubricating your Missile Launcher Locomotive 13

Replacing your Missile Launcher Locomotive’s LEDs and Lamp 14

Operating the rolling stock

Securing the missiles to the flatcars 15

Launching the helicopter 16

Operating the exploding ammunition dump

Assembling and operating the ammunition dump 17-18

Notes 19

Lionel Service 20

Figure 1. COMMAND/CONVENTIONAL switch

3Move ‘em out!

•Get your Missile Launcher Locomotive moving. Press the DIR button on

your CAB-1 remote or Lionel transformer. This sequences the Lionel reverse unit

to the next operating state.

•Adjust track voltage until your Missile Launcher Locomotive moves at your

desired speed. To increase speed, increase track voltage. To decrease speed, reduce

voltage. To stop the locomotive, turn off track power.

•See page 5 for information on locking your Missile Launcher

Locomotive in a single operational state.

Place your Missile Launcher Locomotive on Lionel or

Lionel-compatible O gauge track.

• Set the COMMAND/CONVENTIONAL switch to the CONVENTIONAL position.

Refer to Figure 1 below.

2Power up your Missile Launcher Locomotive with your

transformer.

•Your Missile Launcher Locomotive is designed to operate on 8-18

volts alternating current. Virtually all Lionel and Lionel-compatible

alternating-current transformers are suitable.

Do not power your Missile Launcher Locomotive with direct current

(DC). Damage to sensitive electronic components may occur.

When you first power up your track, the Missile Launcher

Locomotive will wait between 3 and 8 seconds as it “listens” for digital

language from the TrainMaster Command Base (available separately). When it’s

determined that it’s on a conventional (non-Command) railroad, the Missile

Launcher Locomotive’s headlights will illuminate. At this point, the Missile

Launcher Locomotive is in neutral. (This occurs when placing the Missile Launcher

Locomotive on your railroad for the first time. Thereafter, it will start in forward

following every three-second power interruption.)

Running your Missile Launcher Locomotive with a Lionel

transformer

Transformer operations

Caution!

Note!

REAR

Conventional

Command

To select a single operational state for

your Lionel Missile Launcher

Locomotive (example: forward only), you

can deactivate the reverse unit’s sequencing

function with the reverse unit switch.

Get your locomotive moving in the

desired direction, then slow it down without

stopping. Slide the figure toward the rear of

the locomotive as illustrated in Figure 2.

The Missile Launcher Locomotive is now

“locked” into your chosen direction.

When you no longer want single-direction

operation, just slide the figure toward the

front of the locomotive.

Your locomotive’s reverse unit will

“reset” to forward after any five

second or longer power

interruption, regardless of the

original locked-out direction.

Locking your Missile Launcher Locomotive into a single

operational state

Transformer operations

Note!

Figure 2. Reverse unit switch

REAR

FRONT

PROGRAM RUN

Transformer operations

Using your Missile Launcher Locomotive’s ElectroCoupler in the

non-Command environment

Your Missile Launcher Locomotive is

equipped with one ElectroCoupler

located at the rear of the locomotive. To

uncouple rolling stock from your Missile

Launcher Locomotive’s ElectroCoupler in

the non-Command environment, you must

rely on a piece of rolling stock equipped

with Lionel magnetic couplers coupled

directly to your Missile Launcher

Locomotive’s ElectroCouplers. As illustrated

in Figure 3, the magnetic coupler on the

rolling stock will then react to the magnetic

field generated by a Lionel Remote-Control

Track section (available separately). Place

your rolling stock’s coupler “trigger disc”

over the central coil of a Remote-Control

Track section and press UNCOUPLE on the

controller. The magnetic field pulls the disc

downward, and the coupler opens.

Your Missile Launcher

Locomotive’s ElectroCouplers

will NOT open manually or by

using a Remote-Control Track

section.

Magnetic coupler on the rolling stock coupled

to your Missile Launcher Locomotive

Note!

Remote-ControlTrack

section

Figure 3. Trigger disc operation

Transformer operations

Firing your locomotive’s missiles in the non-Command environment

Your locomotive is armed with four plastic missiles. In the non-Command environment,

the missiles are fired one at a time using a Remote-Control Track section (available

separately, 6-65530 for O gauge, 6-12746 for O-27 gauge).

The O-27 Uncoupling Track (6-65149) will not operate the missile launching function.

1. Pull back the metal firing arms and place the four missiles on the locomotive’s launching

platform. Be sure that the missiles lie flat on the platform. Refer to Figure 4.

2. Position the rear truck on the Remote-Control Track section so that the contact shoe rests

on the extra control rails.

3. Press UNLOAD on the Remote-Control Track section controller. One missile will launch

each time the button is pressed.

You can also launch the missiles with the lever at the rear of the locomotive. Each time

you pull the lever to the left, a missile will launch.

Note!

Figure 4. Arming the Missile Launcher Locomotive

TrainMaster Command operations

The Command Control environment

Lionel TrainMaster Command Control is

the advanced model railroad control

system from Lionel. TrainMaster Command

Control gives you the power to operate

multiple Command-equipped locomotives on

the same track, at the same time.

To operate in Command mode, you

need a Command Base and a CAB-1

remote. Find them both at your authorized

Lionel retailer.

Place your Missile Launcher Locomotive on Lionel or

Lionel-compatible O gauge track.

2Address your Missile Launcher Locomotive using the CAB-1.

• Press ENG and 1 on the numeric keypad of your CAB-1 remote. This

command is sent by the CAB-1 to the Command Base, which then translates your

command into digital code. That code is sent around your railroad’s outside rails

in the form of a digital “halo.” All Command-equipped Lionel engines listen to

this digital communication, but they do not respond until they hear their

individual ID number—in this case, “1.”

• The digital language of TrainMaster Command—and not track

power—controls the actions of Command-equipped Lionel

engines. Track power is simply like gasoline in the tank of your car—it gives

you the power to go places, but it doesn’t tell you where to go or how fast to get

there.

• All Command locomotives come factory-programmed with an ID#

of “1.” To change the ID# of your Missile Launcher Locomotive, see page 11.

3Move ‘em out!

• Throttle up or press any command button on the CAB-1. Your Missile Launcher

Locomotive will respond to your every command. Read on.

1• Set the COMMAND/CONVENTIONAL switch to the COMMAND

position. Refer to Figure 1 on page 4.

• Make sure your Lionel Command Base is plugged-in and its

communications wire is connected to the COMMON post on your Lionel

transformer or the U terminal on any of your installed PowerMasters.

• Once positioned on the track, increase track voltage to FULL (no more

than 20 volts). On PowerMasters, slide the CMD/CONV switch to CMD.

Running your Missile Launcher Locomotive in the TrainMaster

Command environment

Press AUX2 to turn

your Missile

Launcher

Locomotive’s

headlights on and

off.

Activates the

keypad.

Press HALT to shut

down all PowerMaster

electrical outputs on

your railroad. Stops all

Command-equipped

locomotives in

operation.

Turn the

THROTTLE

to the right to

accelerate, left to

decelerate.

Your Command-equipped Missile

Launcher Locomotive comes

factory-programmed with an ID# of

“1.” To get your Missile Launcher

Locomotive in action, set PowerMasters

to CMD or set all power supplies on full

(no more than 20 volts). Press ENG

and “1” on your CAB-1. Turn the

throttle or press any command button;

your Missile Launcher Locomotive is

ready for Command operations.

Address Locomotive #1

PowerMasters set to CMD or traditional

power supplies ON FULL (no more than 20

volts)

Press ENG

Press 1 (the ID#)

Throttle up/press any command button

Example

CAB-1 commands for your Missile Launcher Locomotive

Press DIR—the

locomotive decelerates to

a complete stop; turn the

throttle up, and the locomotive will

accelerate in the new, opposite

direction. There is no neutral state.

Press and hold BOOST for

extra power. Release

BOOST and return to the

Missile Launcher Locomotive’s

previous speed.

Press and hold BRAKE to

slow down or stop.

Release BRAKE and

return to the previous speed.

Press and hold to fire

the missiles.

Rear coupler

releases.

TrainMaster Command operations

SET L M H

Beneath this panel

Use HALT only in emergency situations.

Note! 9

Tuning your Missile Launcher Locomotive’s performance

MOMENTUM

TrainMaster Command’s momentum

feature simulates the labored performance

of a locomotive pulling a heavy load. Press

L, M, or H (located under CAB-1’s removable

panel) for light, medium, or heavy

momentum. The Missile Launcher

Locomotive’s Command reverse unit

remembers this setting until you change it.

For quick locomotive response, choose L.

BRAKING AND BOOSTING

There’s more to starting and stopping

than just turning the CAB-1 throttle. Use the

BOOST and BRAKE command buttons—

they give you incremental control of speed

and are the superior way to handle grades,

gradual stops-and-starts, and more.

HIGH VOLTAGE SETTING

Press SET, and the headlights will flash.

Get your locomotive moving to the

maximum speed you want it to run, then

press BOOST. Use this to keep your

locomotive from derailing at excessive

speeds. Turn off the high voltage setting by

pressing SET, then BOOST, holding each for

one second.

STALL

Make your Missile Launcher Locomotive

feel more responsive by setting a “stall”

voltage. Get your locomotive moving, then

press SET; the Missile Launcher Locomotive

will stop. Turn the throttle clockwise to get

the locomotive moving, then decrease speed

until the locomotive just stops. Press SET

again; the Command reverse unit

remembers the stall setting until you

change it. To clear the stall setting, press

SET twice, holding it for one second each

time.

These settings will be lost when you assign a new engine ID number.

Note!

When you press AUX1 on your CAB-1,

you turn the numeric keypad into 10

command buttons. The keypad lets you

control extra command features (until you

press any top-row button like SW, ACC, RTE,

TR, or ENG).

Be sure to press AUX1 before

entering a number on the keypad.

0Stops and resets the Missile Launcher

Locomotive. Resets the Missile

Launcher Locomotive’s direction to

FORWARD.

8Turns off the roof light.

9Turns on the roof light.

CAB-1 numeric keypad commands for your Missile Launcher

locomotive

TrainMaster Command operations

Note!

Altri manuali per Missile Launch Set

Indice

Altri manuali Lionel Giocattolo

Lionel

Lionel Union Pacific RS-3 Manuale utente

Lionel

Lionel BNSF Manuale utente

Lionel

Lionel 6-19868 Manuale utente

Lionel

Lionel 101 Manuale utente

Lionel

Lionel VISION Line Manuale utente

Lionel

Lionel Southern Pacific Overnight Freight Manuale utente

Lionel

Lionel Monopoly Hudson Steam Locomotive Manuale utente

Lionel

Lionel ZW-L Transformer Manuale utente

Lionel

Lionel Illuminated Station Platform Manuale utente

Lionel

Lionel AT&SF Manuale utente

Lionel

Lionel 313 Manuale utente

Lionel

Lionel Shakespeare Express Kinlet Hall Manuale utente

Lionel

Lionel Cab Forward AC-12 Manuale utente

Lionel

Lionel 4-6-2 Pacific Manuale utente

Lionel

Lionel The Polar Express G-gauge Manuale utente

Lionel

Lionel Powered F3 B-Unit Diesel Locomotive Manuale utente

Lionel

Lionel AEC - 57 Switcher Manuale utente

Lionel

Lionel Santa Fe Super Freight Train Se Manuale utente

Lionel

Lionel Fastrack O-36 Manuale utente

Lionel

Lionel Amtrak Acela Manuale utente

Lionel

Lionel Santa's Sleigh Pylon Manuale utente

Lionel

Lionel Caboose Manuale utente

Lionel

Lionel SD90MAC Manuale utente

Lionel

Lionel O-27 Santa Fe FT Passenger set Manuale utente

Manuali Giocattolo popolari di altre marche

marklin

marklin 37321 Manuale utente

Canon

Canon PAPER CRAFT Manuale utente

GREAT PLANES

GREAT PLANES Pitts M-12S Manuale utente

NOCH

NOCH 14261 Manuale utente

Hausler

Hausler 450 SE V2 Manuale utente

Dynaflite

Dynaflite Daydream Manuale utente

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manuale

Kenner

Kenner Batman 63651 Manuale utente

LEGO

LEGO 8527 Manuale utente

iKarus

iKarus ECO 8 Manuale utente

Multiplex

Multiplex EasyStar II Manuale di istruzioni

Walkera

Walkera 38 Manuale di istruzioni

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manuale utente

MD MXION SWD Manuale utente

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manuale utente

marklin

marklin 39671 Manuale utente

Meccano

Meccano 15103 Manuale utente

LEGO

LEGO TECHNIC 8735 Manuale utente