Lippert Components OneControl Manuale del proprietario
Rev: 10.22.2018 OneControl® Programming Manual
OneControl®
PROGRAMMING MANUAL
Rev: 08.06.18 Page 2 CCD-0001736
Safety and System Information
System Information
The OneControl® tablet is an Android-based device that uses the OneControl® application to bring system controls
and monitoring software to a touchscreen tablet. The OneControl® tablet can access the internet (if available), basic
how-to RV videos, product videos, owner's manuals and many more RV owner's resources. The systems controlled
and monitored by OneControl® include slide-outs, leveling systems, awnings, lighting, temperature, water tanks,
tire pressure, battery levels and many more.
The OneControl® Control Panel is accessed within the OneControl® application on the tablet. When powering on
or waking the tablet, the OneControl® application will run automatically as it is pre-configured to do so. In order
for the OneControl®application to present the operator with the MyRV Control Panel, there MUST be power to the
coach. This will power the various OneControl® controllers located throughout the unit. This will also power the
wireless hub and enable connectivity with the tablet, ultimately allowing wireless connectivity. Please note that
with power to the coach, the tablet should always be able to gain access to the OneControl® Control Panel when
placed in the docking station due to it being a wired connection. Use this to assist when diagnosing concerns with
the system.
NOTE: After powering up the RV, it may take several minutes (2-5) for the OneControl® tablet and
OneControl® Hub to fully energize and communicate. Please allow this time for the system to
establish communications to ensure swift application operations.
TABLE OF CONTENTS
Safety and System Information 2
System Information 2
Programming 3
Connecting The OneControl®Tablet To The OneControl®Wireless Network 3
Docking Station 3
Wireless Hub And Range Extender 3
OneControl®Functions 4
Circuit Building For OneControl®Smart Switch 5
Multifunction Fuse Programming 7
Operation 9
Power On/O 9
Volume Button 9
OneControl®10
OneControl®Assembly 11
OneControl®Components 12-18
Notes 19
Rev: 08.06.18 Page 3 CCD-0001736
Programming
Connecting The OneControl®Tablet To The OneControl®Wireless Network
NOTE: Tablet MUST be connected to OneControl® Wifi Hub to complete the programming process.
Placing the hub in a high location away from appliances such as microwaves and refrigerators will
minimize interference.
1. On the OneControl® home page, select “Apps & Internet.”
2. On the "Apps and Internet Browser," select the “WiFi Manager.”
3. Locate the OneControl® Hub (Fig. 1) or Range Extender (Fig. 2) and the label which contains the SSID
and password to the OneControl® system.
4. Match the SSID on the OneControl® Hub or Range Extender (Figs. 1A and 2A) to the corresponding
SSID in the "Wifi Manager."
5. Select the SSID and enter the password located on the OneControl® Hub or Range Extender (Figs. 1B
and 2B) then press "Connect."
NOTE: In order to charge the tablet out of the dock, a 5 volt, 1.8 amp micro USB charger or barrel charging
connector is needed.
AB
Docking Station
The OneControl® system includes a tablet docking station. This is typically mounted near the center of the coach,
and houses the tablet when the wireless operation is unnecessary or during travel. The docking station is wired to
the coach power system and will charge the tablet during its storage period. The docking station is also wired for
communication with the various controllers in the coach. This allows the tablet to function when stored in the dock
and becomes non-reliant on the wireless hub to do so.
Wireless Hub and Range Extender
The OneControl® system is equipped with a wireless hub and range extender. When powered, the hub and range
extender provide the perimeter of the coach with wireless connectivity. This allows the tablet to effectively send
commands wirelessly to the OneControl® system. The hub's and range extender's only purpose is to provide
wireless connectivity. The hub and range extender do not keep configuration data, so when troubleshooting
wireless connection concerns, ensure the tablet can operate the OneControl® Control Panel when housed in the
docking station. Again, as long as there is power to the coach, the OneControl® system should operate from the
dock.
A
B
Fig. 1
Fig. 2
Rev: 08.06.18 Page 4 CCD-0001736
OneControl®Functions
1. Press the yellow LincPad Applications icon 5 times (Fig. 3A).
2. A pop-up window will prompt the user to enter password (Fig. 4). The password is the last 4 digits of
the version located in the bottom right hand of the tablet desktop (Fig. 4A).
3. After a password is entered, the Configurator Icon will appear (Fig. 5A). Press the Configurator Icon.
4. To view all components available, press “Show All Devices” (Fig. 6). (A sub list will appear with options:
By product/controller, By functions, By type, Show all devices. )
A
Fig. 3 Fig. 4
Fig. 5 Fig. 6
A
A
Rev: 08.06.18 Page 5 CCD-0001736
5. Select the relay (latching or reversing polarity) switch or tank sensor to assign a title (Fig. 7).
6. When window pops up select “Rename” (Fig. 8).
7. Select “Group”.
8. Select “Name”.
9. Press “Send” to set group and name selected (Fig. 9).
10. Repeat process for each function.
Circuit Building For OneControl®Smart Switch
1. Press “Build Circuit” (Fig. 10).
Fig. 7 Fig. 8
Fig. 9
Fig. 10
Rev: 08.06.18 Page 6 CCD-0001736
2. Select first device by pressing the preferred icon. Then press Select when the pop-up window shows
up on the screen (Fig. 11). Device title will highlight in yellow (Fig. 12).
3. Repeat process for each device included in the circuit.
4. Once you have selected (highlighted) all devices for the circuit, press one of the highlighted device
icons. Press “Create Circuit” in pop-up window (Fig. 13). The next screen will show all devices included
in the circuit and assign a circuit number (Fig. 14).
Fig. 11 Fig. 12
Fig. 13 Fig. 14
Rev: 08.06.18 Page 7 CCD-0001736
Multifunction Fuse Programming
1. Enter the OneControl® configurator screen by tapping the yellow LincPad Applications icon five (5)
times (Fig. 15A). You will then be prompted to enter a four-digit password (Fig. 15B). The password is
the last four digits of the version number (Fig. 15C).
2. Choose the "Configurator" option (Fig. 16A).
C
3. Choose the "Show All Devices" option (Fig. 17A).
4. Choose the "By Product/Controller" option (Fig. 18A). This will display all of the products and
controllers connected to the Linc system.
5. Press and HOLD the "Multifunction 8-Output" option (Fig. 19A). You will then be prompted to
configure the fuses. Choose "OK" (Fig. 20A) to enter fuse configuration.
A
AA
AA
Fig. 15 Fig. 16
Fig. 17 Fig. 18
Fig. 19 Fig. 20
A
B
Rev: 08.06.18 Page 8 CCD-0001736
6. When in the fuse configuration menu, a list of all labeled and unlabeled relay functions will appear (Fig.
21). Select the fuse location from the drop down menu on the right (Fig. 21A and Fig. 22).
Fig. 21
A
Fig. 22
7. Once all fuse locations are chosen, press and HOLD anywhere on the screen for a pop up menu
confirming the fuse locations. Press and hold the sync button on the multifunction receiver (Fig 23A).
While holding the sync button, press "OK" on the "Send All" prompt (Fig. 24A). This will program all
fuse positions.
A
Fig. 23 Fig. 24
A
Rev: 08.06.18 Page 9 CCD-0001736
Operation
Power On/Off
1. To power ON the tablet, hold and release the power button for 2-3 seconds (Fig. 25).
NOTE: It will take a few moments to start up and load the system.
2. To enter or exit sleep mode, press and release power button.
3. To power OFF the tablet, press and hold the power button until a utility screen appears.
4. Select "Power off".
5. Press “OK” when confirmation box displays: “Your tablet will shut down.” (Fig. 27).
Volume Button
1. Volume control is located on the side of the tablet (Fig. 25). There is also a volume icon on the menu
screen.
Reset
Volume Control
Charging Port
Micro USB
Headphone Jack
Power Button
Microphone
TF/Micro SD
Card Port
Fig. 25 Fig. 26
Fig. 27
Rev: 08.06.18 Page 10 CCD-0001736
OneControl®
1. Locate the “OneControl® Control Panel” on the menu screen (Fig. 28A).
2. Pushing the “OneControl® Control Panel” tab will open the “OneControl® Applications” screen. This
screen will display all the icons of the devices on the RV that can be operated with the OneControl®
Tablet.
3. Push the icon of the device you wish to operate.
4. Push the “Home” icon button, located in top right of screen, to return to “OneControl® application”
screen.
NOTE: OneControl® includes text and video resources, including owner’s manuals and troubleshooting
videos.
Fig. 28
A
Altri manuali per OneControl
1
Indice
Altri manuali Lippert Components Tavoletta
