Lippert Tire Linc Manuale utente
Tire Linc® LCD Display
owner's manual
Rev: 10.13.21 Page 2 CCD-0004221
TABLE OF CONTENTS
Introduction 2
Key System Components 3
Safety 3
Preparation 4
Install Repeater 4
Place Repeater Into Pair Mode 4
Message To Power O Displays 5
Pairing and Conguration 5
Sensor Pairing 5
Sensor Pairing Sequence 7
Learn All Sensors 8
Congure All Thresholds 9
Learn A Sensor 10
Detach Vehicles 11
Re-Attach Vehicles 12
Delete A Vehicle 13
Add Another Vehicle 14
Replace Sensor 14
Display 15
Operation 16
Tire Limits Example 17
Changing Units of Measure 17
Troubleshooting 18
Relearn Sensors After Tire Rotation 18
Internal Sensors 18
Wrong Vehicle Chosen 18
Missing Stem Sensor 18
No Power 19
Reset Repeater 19
Reset LCD Handheld Display 19
Introduction
Tire Linc® is a tire pressure and temperature monitoring system (TPMS). The TPMS display issues an alert
when a unit's pressure or temperature falls out of the programmable range. The system is operated by a
handheld display, and a power cord and stand are included with the kit (Fig.1).
NOTE: If utilizing the LCD handheld display with the repeater, then neither the OneControl app nor the Tire
Linc Alert Indicator can be used with the repeater.
NOTE: Images used in this document are for reference only when assembling, installing and/or operating
this product. Actual appearance of provided and/or purchased parts and assemblies may differ.
For information on the assembly or individual components of this product, please visit:
https://support.lci1.com/tire-linc.
Do not use tire sealant with internal sensors. This will damage the sensor and void the warranty.
Rev: 10.13.21 Page 3 CCD-0004221
Fig. 1
The "WARNING" symbol above is a sign that a procedure has a safety risk involved and may cause
death, serious personal injury, severe product and/or property damage if not performed safely and
within the parameters set forth in this manual.
Failure to follow instructions provided in this manual may result in death, serious personal injury
and/or severe product and property damage, including voiding of the component warranty.
Moving parts can pinch, crush or cut. Keep clear and use caution.
Tire Linc LCD Display Components
Callout Part Number Description
A2020222357 TPMS handheld display
B2020222358 TPMS handheld display power cord
C2020222360 TPMS handheld display stand
Safety
Read and understand all instructions before installing or operating this product. Adhere to all safety labels.
This manual provides general instructions. Many variables can change the circumstances of the instructions,
e.g., the degree of difficulty, operation and ability of the individual performing the instructions. This
manual cannot begin to plot out instructions for every possibility, but provides the general instructions,
as necessary, for effectively interfacing with the device, product or system. Failure to correctly follow the
provided instructions may result in death, serious personal injury, severe product and/or property damage,
including voiding of the LCI limited warranty.
A
B
C
Key System Components
Sensors - 188 psi maximum pressure reading, -58 to 401 °F (-50 to 205 °C) temperature measurement
range—Stem Sensor Working Range: 185 to -4 °F (85 to -20 °C).
Repeater - Receives sensor data.
Repeater Dock - Provides power to repeater, which then “docks” to this base.
LCD Display - Device to set up and operate system.
On prepped units, internal sensors have been installed in the tires, the repeater dock has been connected
to the unit's power source and the repeater has also been installed in the dock. If the repeater is not already
installed in the dock, instructions are included to describe how to snap the repeater into the dock.
Rev: 10.13.21 Page 4 CCD-0004221
Fig. 2
Preparation
NOTE: The repeater for the TPMS system is already installed on prepped units. If installed, continue to
the Place Repeater Into Pair Mode and/or Sensor Pairing, Configuration sections. However, if the
repeater is not in place in the dock, use the following instructions to install the repeater.
Install Repeater
1. Locate and remove film cover (Fig. 2A) from repeater dock.
NOTE: Film cover should be removed only when ready to install repeater.
2. Snap the repeater (Fig. 2B) into the repeater dock (Fig. 2C).
NOTE: The repeater dock is keyed and the repeater can only be installed in one way.
3. The repeater will power on, lighting up the Status LED (Fig. 2D) and blinking to indicate the repeater
has power.
NOTE: If the Status LED does not light up, check the in-line fuse to the dock to ensure the dock has power.
A
D
BC
Place Repeater Into Pair Mode
NOTE: Pair Mode is usually not necessary for the display to pair to the repeater. Pair Mode is needed
only when attempting to pair the display to the repeater and more than one repeater is located
nearby. When the repeater is in Pair Mode, the BLE (Bluetooth Low Energy) name TireLinc changes
toTireLinc*.
1. If Pair Mode is needed, tap and hold the Pair Mode button on the repeater (Fig. 2E) until there is one
long red blink followed by two short red blinks. This takes approximately five seconds.
2. Release the button.
E
Rev: 10.13.21 Page 5 CCD-0004221
Pairing and Configuration
Sensor Pairing
1. Turn on LCD display using On/Off button on bottom of the display (Fig. 4).
2. Tap the Scan for New Bluetooth Devices arrow (Fig. 5) and look for the TireLinc listing.
NOTE: If the repeater is in Pair Mode, look for TireLinc*.
3. Select the first listing (Fig. 6) and tap CONTINUE.
4. Tap SETUP COACH (Fig. 7).
Micro USB Port
For Charging
On/Off Button
Sync Button
Reset
Fig. 3
Fig. 4 Fig. 5
Fig. 6
Message To Power Off Displays
Whenever a user accesses one of three modes in the Settings menu — Add Another Vehicle, Learn
All Sensors or Learn A Sensor — a screen will appear on the display for five seconds (Fig. 3) before
automatically transitioning to the notifications received before sensor learning takes place.
Fig. 7
Rev: 10.13.21 Page 6 CCD-0004221
5. Select a vehicle class (Fig. 8) and tap CONTINUE.
6. Select the type of vehicle to be set up by choosing one of the pictures shown on the display (Fig. 9)
and tap CONTINUE.
7. Determine if a spare tire will be added (Fig. 10). Tapping YES will add the spare tire icon to the
vehicle selected.
8. After tapping YES or NO for a spare tire, the display will automatically change to the Learn All
Sensors mode.
9. Notifications will instruct how to learn internal and external sensors.
10. Continue to the Learn All Sensors section.
Fig. 9
Fig. 10
Fig. 8
Rev: 10.13.21 Page 7 CCD-0004221
Sensor Pairing Sequence
The pairing sequence for tires begins with the left front tire first (Fig. 11-1), continuing from front to rear and
then beginning again at the right front (Fig. 11-5) and continuing to the rear tires. The spare tire (Fig. 11-9)
islast.
With dual wheels on a vehicle, the outside tires on either side (Fig. 11-2, 6) are paired first before the inside
tires (Fig. 11-3, 7).
Figure 11 provides an example of the pairing sequence for tires on any vehicle.
Fig. 11
Rear
12
3
4
56
78
9
Spare
Front
Rev: 10.13.21 Page 8 CCD-0004221
Learn All Sensors
A screen will appear on the display for five seconds (Fig. 3) before automatically transitioning to the
notifications received before sensor learning takes place.
1. After entering the Learn All Sensors mode, hold the LCD display close to the sidewall in the area
opposite the valve stem of the tire to be paired (Fig. 12).
2. Tap and hold the sync button on the LCD display (Fig. 4) to pair the sensor until the display beeps and
the red flashing circle turns green.
3. The display will feature a red dot (Fig. 13A) representing the tire that is being paired, which will then
turn green (Fig. 14A) when it is successfully paired (Figs. 13 and 14).
4. When pairing has been completed, the display will ask if another vehicle is to be added to the
system (Fig. 15). If tapping YES, pair the additional sensors in the proper sequence. If not, continue to
Configure All Thresholds.
NOTE: There are limits of three vehicles and 20 tires.
Fig. 12 Fig. 13
Fig. 14 Fig. 15
A
A
Rev: 10.13.21 Page 9 CCD-0004221
Configure All Thresholds
1. Before accessing the SETTINGS menu, check to make sure the vehicle selected to have thresholds
configured is present on the main tire pressure screen (Fig. 9).
2. Select the Configure All Thresholds arrow on the SETTINGS screen (Fig. 16A).
3. Set the Minimum Pressure, Maximum Pressure, Maximum Temperature and Maximum Temp Change
for the sensors (Fig. 17).
4. After each selection, tap FINISH.
Fig. 16 Fig. 17
A
Rev: 10.13.21 Page 10 CCD-0004221
Learn A Sensor
A screen will appear on the display for five seconds (Fig. 3) before automatically transitioning to the
notifications received before sensor learning takes place.
1. Before accessing the SETTINGS menu, check to make sure the vehicle on which a sensor is to be
learned is present on the main tire pressure screen (Fig. 9).
2. Tap the arrow to the right of Learn A Sensor (Fig. 18A).
3. The vehicle will at first appear without a red blinking dot. Select the tire with a sensor to be learned
(Fig. 19A) and observe a red blinking dot on that tire (Fig. 20A).
NOTE: The procedure for learning a sensor is the same as relearning sensors.
4. Hold the LCD display close to the sidewall in the area opposite the valve stem of the tire to be
paired (Fig. 21).
5. Tap and hold the sync button on the LCD display to pair the sensor until the display beeps and the red
flashing circle turns green (Fig. 21).
6. The display will feature a red dot representing the tire that is being paired, which will then turn green
when it is successfully paired.
Fig. 18 Fig. 19
Fig. 20 Fig. 21
A
A
A
Altri manuali per Tire Linc
3
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Lippert Monitor
