LiveWatch Simon XTi Manuale utente

For the most current resources, helpful videos and live chat visit:

www.livewatchsecurity.com/login

Simon XTi with Plug & Protect™

Quick Start Guide

This guide covers the fundamentals of

Step 4 and Step 5:

Thanks for choosing Plug & Protect™ from SafeMart. This product is designed to be quickly

placed in your home or office while offering comprehensive protection. Your home will be fully

protected in just a few minutes. This guide is designed to aid you in the placement of your

sensors and master control unit. Please read this guide in its entirety before placing your

sensors. This system has been programmed to your specifications and sensor placement labels

have been applied to each sensor. It is important not to separate the labeled boxes from the

sensors until you are ready to place the devices in the locations stated on the label.

Be sure to follow along with the “Plug & Protect™ Installation Video” sent to your

email address. This video can also be found online at www.Help.SafeMart.com.

Disclaimer – Important Information, Please read

Trademarks and patents: SafeMart and LiveWatch logos, are registered trademarks of LiveWatch Security LLC.

Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or

vendors of the respective products.

Warning: The unauthorized reproduction or distribution of this copyright work is illegal. Criminal copyright

infringement, including infringement without monetary gain, is investigated by the FBI and is punishable by up to

5 years in federal prison and a fine of $250,000.

Disclaimer: The information in this document is subject to change without notice. LiveWatch Security LLC

(“LiveWatch Security”) d/b/a SafeMart assumes no responsibility for inaccuracies or omissions and specifically

disclaims any liabilities, losses, or risks, personal or otherwise, incurred as a consequence, directly or indirectly,

of the use or application of any of the contents of this document. For the latest documentation, log in at

LiveWatchSecurity.com/Login.

This publication may contain examples of screen captures and reports used in daily operations. Examples may

include fictitious names of individuals and companies. Any similarity to names and address of actual businesses

or persons is entirely coincidental.

Safety Information: Before you install your products, please read the appropriate information, notices and other

material, including the safety and site preparation section in your product documentation. For your safety, please

consult a professional if you have any questions. There are certain components that connect to high voltage

electrical outlets. Improper installation or workmanship by you (the installer) can lead to severe injury, property

damage, system malfunction or death.

This guide is provided as information about low voltage products. Since every low-voltage project is unique, any

information contained herein WILL NOT constitute an endorsement of the suitability of any equipment or

application. Use this product only for the purpose it was designed. For the latest documentation, contact

LiveWatch Security d.b.a. SafeMart log in at LiveWatchSecurity.com/Login

Identify the Components in the Box

For the most current resources, helpful videos and live chat visit:

www.livewatchsecurity.com/login

Motion Detector

Simon XTi (Master Control Unit) Door & Window Sensors

Optional Keychain Remote

1. After taking all the items out of the

box, the first step is to plug in your

Master Control Unit into any outlet.

This will allow the rechargeable

backup battery, which is already

connected inside, to charge enough

for us to find a good location suitable

for the Master Control unit.

2. Your system should be powered up

and the display should be active.

Leave it plugged in for 5-10 minutes.

1. Tip: The location of your master control unit should be:

• Near a power outlet within reach of the unit’s power cord.

• Away from windows–the display cannot be seen from outside.

• On a surface that is easily accessible to you.

• Away from wireless routers, wireless telephones, or large

metallic objects such as a flat screen TV.

• In an area with cellular service (see next step).

2. Test: Test the strength of your cellular signal by pressing the Gear

Wheel in the lower right hand corner of the home screen. Press the

down arrow several times to scroll to the last page. Choose

“Programming” by pressing “Enter” next to this option. Enter your

Installer Code. By default this is 4, 3, 2, 1. Then press “OK”. Next,

choose “Interactive Services” and then “Module Status” on the next

screen. The strength of the cellular signal between the tower and your

panel is shown on the top line and indicated on a scale of 5 bars. You

need a minimum of 2 solid white bars to have a solid cellular

connection.

3. Complete: If you do not have a solid connection, unplug your Master

Control Unit and walk around your home performing the same test

until you receive 2 solid white bars or more. Once the panel has a good

connection, you may now plug in your Master Control Unit into a

nearby outlet.

1a: Plug in Your Master Control Unit

1b: Find a Location For Your Master Control Unit

For the most current resources, helpful videos and live chat visit:

www.livewatchsecurity.com/login

Gear Wheel

After

Before

1. Select a location on the door or window you are going to protect. The

larger part of the contact should be on the non-movable part of the

door/window frame - see diagram.

2. After peeling off the wax paper backing on the tape, mount the two

contacts by applying pressure to the door/window. When you mount:

• Place the sensors at a maximum of ½” apart – closer is better.

• Do not exceed the width of a pencil between the sensors.

• The small arrows on the components need to be aligned and

facing each other on the inside of the mount.

1. Remove the double sided backing from the tape on the back of the

sensor.

2. We recommend mounting these sensors in the corners of the rooms

you are protecting. Do not place the motions towards a window facing

the outside; place them facing in, towards the inside of your home; in

an area where a burglar may pass. Once the tape is peeled place the

sensor about 7 or 8 feet high in the corner. Press the motion sensor

hard into place. Once the adhesive is secure, you have completed the

installation.

If your doors or windows do not allow you to properly place the large part of the

sensor on the frame, it is okay to place the smaller portion on the door or

window frame to make the placing work more easily. This is an acceptable

method of sensor placement although it should only be used when necessary.

2a: Place the Door and Window Sensors

2b: Place the Motion Sensors

For the most current resources, helpful videos and live chat visit:

www.livewatchsecurity.com/login

There are 2 “arming modes”: Stay Mode and Away Mode.

1. Stay Mode arms the perimeter (windows and exterior doors for

example) and is usually used while you are home.

2. Away Mode arms the perimeter as well as the interior sensors

(motion sensors for example) and is usually used while you are

away from the phone.

Arm your system

1. Master Control Unit

•Stay Mode: Press the Open Lock Icon on the main screen and

then the “Doors & Windows Only” (Stay) button.

•Away Mode: Press the Open Lock Icon on the main screen and

then the “Arm All” (Away) button.

2. Keychain Remote (Optional with purchase.)

•Stay Mode: Press the Closed Lock Icon for two seconds.

•Away Mode: Press the Closed Lock Icon for two seconds and

then press it once more for two seconds.

3. Alarm.com App or Website

•Stay Mode: Press the “Arm (Stay)” icon.

•Away Mode: Press the “Arm (Away)” icon.

Disarm your system

1. Master Control Unit

•Press the Closed Lock Icon on the Master Control Unit. Enter

your Master Passcode and press “OK”. (Your Master Passcode

was created in the LiveWatch Customer Center and was sent to

you in a confirmation email.)

2. Keychain Remote (Optional with purchase.)

•Press the Open Lock Icon on your keychain for 2 seconds.

3. Alarm.com App or Website

•Press the “Disarm” icon on your phone.

When arming and disarming your system, the master control unit will beep to

indicate that you have a given amount of time to either exit when leaving or enter

your code when entering. This is known as Entry/Exit Delay. When the armed master

control unit begins the count down by beeping, the beeps that it gives off will cease

once the system is armed. Your system will not beep the entire time you are gone,

only the time that is set under Entry/Exit Delays; commonly 45 or 60 seconds.

3: Arm and Disarm Your System

For the most current resources, helpful videos and live chat visit:

www.livewatchsecurity.com/login

Optional Keychain RemoteMaster Control Alarm.com App

•Before you are ready to activate your system, log into your

LiveWatch Customer Account and make sure that you have

completed Steps 1-4 in your Customer Dashboard.

• A SafeMart support technician will call you on the date and time of

your scheduled appointment to test and activate the system. Please

be at the location of the system.

• If you are unable to make your scheduled appointment, please visit

www.livewatchsecurity.com/login to reschedule.

After your system is tested and activated you will receive:

• Your account number (eg: ABC7890)

• The phone number for our 24/7 Central Station

You can customize your system using the Alarm.com website. The

SafeMart technician will provide you with a login and password during

your activation appointment.

4: Activate and Test Your System

For the most current resources, helpful videos and live chat visit:

www.livewatchsecurity.com/login

Note:You must log in over a computer internet browser before using your Smartphone App.

Control Your Secure Home Remotely with LiveWatch!

The fastest answers 24/7 can be found

at: www.livewatchsecurity.com/login

Mobile Apps

•iPhone: Download the free Alarm.com App for your iPhone or iPod

touch (iOS 3.2 or later required). Search for "Alarm.com" in the

App Store.

•iPad: Download the free Alarm.com App for your iPad (iOS 3.2 or

later required). Search for "Alarm.com" in the App Store.

•BlackBerry: Download the free Alarm.com App for BlackBerry by

visiting www.alarm.com/bbinstall from the web browser of your

compatible BlackBerry device. (Requires OS 4.2.1 or later.

Compatible with the BlackBerry Curve, Pearl, Bold, and 8800 series

devices.)

•Android:To download the free Alarm.com App for Android

(compatible with Android OS 1.6 or later), visit the Google Play

Store from your device and search for "Alarm.com".

•Mobile Site: Have web access on your cell phone? Just open its

web browser and go to the Mobile Site URL (m.alarm.com) to log

into your account. The Mobile Site includes many features of the

primary website and is specially formatted to fit your mobile screen.

Monitor and control your system

from the road with these free tools

for mobile devices.

On the Go?

For the most current resources, helpful videos and live chat visit:

www.livewatchsecurity.com/login

Thank*you*for*choosing*SafeMart*and*LiveWatch*Security.

For the most current resources, helpful videos and live chat visit:

www.livewatchsecurity.com/login

Indice

Altri manuali LiveWatch Sistema di sicurezza

LiveWatch

LiveWatch Simon XT with Plug & Protect Manuale utente

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente