LMI Technologies MikroCAD Manuale utente

Quick Start Guide

15215-01.05_MANUAL_Quickstart_MikroCAD_premium1.6x1.2_revB

MikroCAD

premium 1.6 x 1.2

Getting Started with the MikroCAD Scanner

Congratulations on purchasing a MikroCAD 3D Scanner. This quick start guide provides you with

the resources to get you started on 3D scanning.

Downloading the Software

You can download the MikroCAD installer at http://lmi3d.com/support/downloads/mikrocad.

If you purchased the MikroCAD software (Standard or Professional), download 14471-x.x.x.x_

SOFTWARE_MikroCAD_Standard_Professional.exe.

If you purchased only the scanner, download 14470-x.x.x.x_SOFTWARE_MikroCAD_Scan.

exe.

Customer Support

If you have any installation issues, please contact:

AMERICAS

LMI Technologies (Head Oce)

Vancouver, Canada

+1 604 636 1011

EMEAR

LMI Technologies GmbH

Berlin, Germany

+49 (0)3328 9360 0

ASIA PACIFIC

LMI (Shanghai) Trading Co., Ltd.

Shanghai, China

+86 21 5441 0711

LMI Technologies has sales oces and distributors worldwide. All contact information is listed at

lmi3D.com/contact/locations.

Hardware Included with Your MikroCAD Scanner

Number Description

1 3D Scanner and stand

2 Two Ethernet cables (one long, one short)

3MikroCAD software dongle (separate purchase; required for using measurement

tools)

4 Power over Ethernet injector and power cord

5 Calibration kit

When you receive your MikroCAD scanner, check that all components are included:

Installing the MikroCAD Software

1. After downloading the MikroCAD sofware installer, double-click it.

See “Downloading the Software” on page 2 for information on downloading the

installer.

2. Accept the license agreement and then click Next repeatedly to step through the

installation setup.

You may change the default values if you wish, but we recommend leaving .NET Runtime

4.0 selected to ensure that it is installed.

3. Click Install.

The installer installs the MikroCAD software.

4. Restart the computer if you are instructed to do so.

Connecting the Scanner Cables

1. Using the short Ethernet cable, connect the Data/IN port on the Power over Ethernet

injector to an Ethernet port on the computer (sold separately).

2. Using the long Ethernet cable, connect the P+D/OUT port on the Power over Ethernet

injector to the scanner’s Ethernet port.

Using the Scanner

1. Connect the power cord to the Power over Ethernet injector, and plug the other end of the

power cord into a wall outlet to power up the scanner.

The LED on the top of the scanner starts ﬂashing after roughly 30 seconds, turns o for

roughly 30 seconds, and then turns on again and remains on. The scanner is ready when the

LED remains on.

2. Turn the computer is on.

3. If you are going to perform measurements, insert the dongle into a free USB port.

The dongle is required to perform measurements, but not to acquire data.

Windows may install a driver when you insert the dongle.

4. Launch the MikroCAD software.

If the scanner is not listed in the scanner selection dialog, or if the scanner repeatedly tries

to connect to the scanner, see “Troubleshooting” on page 12.

5. Put the sample below the scanner in the center of the camera image.

Looking into the light projector for more than one minute presents a risk to

vision. Avoid looking into the light projector or limit exposure to less than

one minute.

6. Conﬁgure the brightness using the slider in the MikroCAD software.

Use the Intensity Proﬁle graph in the software to guide you. Try to set the brightness so

that most of the peaks are below 256 and near the middle of the graph.

If you see no image, see “Troubleshooting” on page 12.

7. Focus the scanner.

To focus the scanner, align the vertical line of the projected cross pattern with the vertical

line of the red cross in the MikroCAD software.

Use the small knob on the column stand to ﬁne-tune the focus. Use the large knob on the

column stand to move the scanner more quickly.

For coarse

adjustment

For ﬁne

adjustment

8. On the Scan page, in the Acquisition group, click on Scan to perform a scan.

Altri manuali per MikroCAD

Indice

Altri manuali LMI Technologies Scanner

LMI Technologies

LMI Technologies Gocator 2075 Manuale utente

LMI Technologies

LMI Technologies HDI 100 Series Manuale utente

LMI Technologies

LMI Technologies FocalSpec Manuale utente

LMI Technologies

LMI Technologies HDI 100 Series Manuale utente

LMI Technologies

LMI Technologies HDI Advance Manuale utente

LMI Technologies

LMI Technologies MikroCAD premium Manuale utente

LMI Technologies

LMI Technologies MikroCAD premium Manuale utente

LMI Technologies

LMI Technologies chroma+scan 20 0 Series Manuale utente

LMI Technologies

LMI Technologies HDI 109 Manuale utente

LMI Technologies

LMI Technologies HDI 120 Manuale utente

LMI Technologies

LMI Technologies chroma+scan 24 0 Series Manuale utente

LMI Technologies

LMI Technologies Gocator 1300 Manuale utente

LMI Technologies

LMI Technologies Chroma+scan 21X5 Manuale utente

LMI Technologies

LMI Technologies HDI 120 Manuale utente

Manuali Scanner popolari di altre marche

Plustek

Plustek Scanner Manuale utente

Z/I Imaging

Z/I Imaging PhotoScan 2001 Manuale utente

Renkforce

Renkforce DS100-5M Manuale utente

Image Access

Image Access WideTEK A2 Manuale utente

Canon

Canon imageFORMULA CR-120N Manuale utente

Fujitsu

Fujitsu FI-4860C2 Manuale utente

GeoSlam

GeoSlam ZEB Horizon Istruzioni per l'installazione

Kodak

Kodak i5800 Scanner Manuale utente

Kodak

Kodak i7300 Manuale utente

Revopoint

Revopoint POP Manuale utente

Fujitsu

Fujitsu fi-4860C Manuale utente

Eddyfi Technologies

Eddyfi Technologies Floormap X Manuale utente

Faselase

Faselase F6 Manuale utente

Fujitsu

Fujitsu CardMinder Manuale utente

Uniden

Uniden BC340CRS Manuale utente

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Manuale utente

Mustek

Mustek PageExpress 4800 Pro Manuale utente

Optex

Optex 750830 Manuale utente