LOCKLY GUARD DUO 679D Manuale utente
INTERCONNECTED EDITION
INSTALLATION
GUIDE
DUO (679D)
FOR COMMERCIAL USE & PROFESSIONAL INSTALLATION
WWW.LOCKLYPRO.COM
PGD679DW
GET THE MOST OUT OF YOUR
LOCKLY GUARD™
Get the latest user/installation manuals , instructional videos, and FAQs
SCAN or VISIT
Locklypro.com/679D
Reference installation parts overview foldout on back page
Welcome!
This guide will walk you through step-by-step how to
install and get Lockly Guard™up and running. Instal-
lation generally takes less than 30 minutes. If you
have any questions please call our VIP Hotline (855)
562-5599 for help.
3
Phillips Screwdriver
To complete the installation you will need:
Flathead Screwdriver Tape measure or ruler
Preparation
Pliers
Optional
Screwdriver with drill bits
Drilling maybe required to install this lock. If you are installing your lock on a brand new
door, a drill is required if there are no holes prepared for lock installation. Use provided
template to bore holes on door.
4
Preparation
Measure and confirm your door is
between 1-3/8" - 2"
(
35mm - 50mm).
Measure and confirm the hole in the
door is 2-1/8" (54mm).
Measure and confirm that the
backset is between 2 -3/8" (60mm)
to 2 -3/4" (70mm).
Measure and confirm that hole in
the door edge is 1" (25mm).
Remove existing door hardware, latch or deadbolts before installing the new lock.
Use provided template to bore new holes if needed.
1
2
3
4
Measure and confirm that distance
between front door holes is
4"(101.6mm) or 5.5"(139.7mm)
5
1- 3/8"—2"
(35mm—50mm)
2-3/8"(60mm)
or
2-3/4"(70mm)
2-1/8"
54mm
54mm
1"
25mm
4"(101.6mm)
or
5.5"(139.7mm)
2-1/8"
1"
25mm
*Optional
IMPORTANT NOTICE
* Use goggles to protect eyes if you need to drill door holes.
5
INSTALLING THE LOCKSET
Step 1
1
2-3/8"(60mm) 2-3/4"(70mm)
(a)
I. Push the crank (a) to extend
the deadbolt (b)
Deadbolt Adjustment
Latchbolt Adjustment
b
cd
dc
a
Push the shaft (a) to adjust the lockset
to 2-3/8"(60mm) or 2-3/4"(70mm).
2-3/8"
(60mm)
2-3/4"
(70mm)
G
G
G
G
Measure the distance between center of front door hole to the edge of your door hole to
determine the backset. Adjust latchbolt Fand deadbolt Jaccording to the backset
of your door.
II. Hold the metal plate (c) and
twist the deadbolt body (d)
clockwise till it snaps to 2-3/8"
III. To return to default status, while
the deadbolt (b) is extended,
hold the metal plate (c) and
twist the dead bolt body (d)
counter-clockwise till it snaps to
2-3/4"
6
INSTALLING THE LOCKSET
Step 1
continued
J
G
G
F
Install deadbolt J (top) and latchbolt F(bottom) to door and secure with screws G.
Retract deadbolt and make sure bore hole is horizontally positioned.
Optional: Stainless steel mortise slot cover, 4" or 5.5" Face Plates available. To purchase,
PGA018
PGA019 PGA019S
For mortise slot
5.5” 4”
3
After adjusting the latchbolt F, determine the orientation of the latchbolt.
Determine the orientation of latchbolt. Facing the door exterior, install the
latchbolt according to the opening direction of your door.
2
LEFT OUT-SWING DOOR
LEFT IN-SWING DOOR
RIGHT OUT-SWING DOOR
RIGHT IN-SWING DOOR
Inside
Inside
Outside
Outside
Inside
Outside
Inside
Outside
7
CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS
Step 2
Changing the Exterior Handle Orientation
(Right handle)
Insert key and rotate lock
face so that the two white
dots align as shown.
12
R
Use the provided pin insert Rto push the metal
pin located at the 3 o’clock of the the base
handle, then the other pin at 9 o’clock position.
Remove the handle once the pins are
compressed.
The lock ships with handle default for right in-swing or left out-swing door. Check the diagram below
if you are unsure of you door orientation.
Hinge
Side
RIGHT IN-SWING DOOR
LEFT OUT-SWING DOOR RIGHT OUT-SWING DOOR
LEFT IN-SWING DOORINTERIOR
EXTERIOR
No need to change door handle
orientation. Skip Step 2.
LEFT-IN SWING and RIGHT OUT-SWING DOORS
require changing the door handle orientation.
Contnue to follow Step 2 to change exterior
and interior door handle orientation.
3
8
CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS
Step 2
continued
Twist key back to horizontal position. The key can
be taken out once it goes back to the horizontal
position.
4
5 6
Rotate the handle 180° to the other side
of the lock.
Using your fingers, press the two pins located
on the left and right side of the the lock
to insert the handle back onto the lock.
Check that your handle works smoothly
by giving it a turn up and down.
Confirm that your installation was complete by
checking if the pins are flush against the handle,
and has popped out. Adjust the handle accord-
ingly to make sure the pins are fully decom-
pressed and sits flush against the surface.
9
CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS
Step 2
continued
7
8
Align the screw hole on point "L"
then insert the removed screw
and tighten.
At the back of the exterior
panel, remove the screw
on point "R".
Indice
