Lockly Vision Manuale utente

INSTALLATION GUIDE

DEADBOLT EDITION

SMART LOCK w/ HD

VIDEO DOORBELL

VISION

Lockly Secure can be fitted for both

right swing doors and left swing doors.

Parts List

Labeled

As Description Count

AKeys 1

BExterior Assembly 1

CExterior 1

DMounting Plate 1

EAdhesive 1

FUNF10-32*60mm Screw 2

GInterior Assembly 1

HPM4*12MM Screw 2

IBattery Cover 1

JDeadbolt 1

KKA4*20MM Screw 4

L-1 Strike Plate（Optional）1

M-1 Adhesive（Optional）1

L-2 Strike Plate（Optional）1

M-2 Strike Plate（Optional）1

STEP 1: PREPARE DOOR FOR INSTALLATION

L-1M-1L-2M-2

STEP 1: PREPARE DOOR FOR INSTALLATION

1.1: To complete installation, you would need the following:

1.2: Prepare door and remove existing lock. If necessary, use provided

Installation Template to prepare door.

Phillips Screwdriver

Flathead Screwdriver

Ruler

Screwdriver with drill bits

(optional)

1-⅜" (35mm)

to 2" (50mm)

1" (25mm)

2-⅜" (60mm)

or 2-¾" (70mm)

2-⅛" (54mm)

STEP 2. ADJUST DEADBOLT AND INSTALL

2.1: Deadbolt slit hole must be aligned to the center of the door hole. If not

adjust as shown below:

2.1.1:

Wear gloves during adjustment

to prevent pinching your hands)

Hold the metal

plate (c) and twist

the deadbolt body

(d) clockwise till it

snaps to 2-3/8"

To return to default status,

while the deadbolt (b) is

extended, hold the metal

plate (c) and twist the dead-

bolt body (d) counter-clock-

wise till it snaps to 2-3/4"

(b)

（a）

（c）（d）

Push the crank

(a) to extend the

deadbolt (b)

STEP 2. ADJUST DEADBOLT AND INSTALL

2.2: Extend the deadbolt by inserting a

flat head screwdriver on the slit hole or

by pushing the crank towards the metal

face plate.

2.3: Insert the Deadbolt to the edge

door hole, make sure that its right side

up and the slit hole is in vertical position,

then fastened with 2 screws (K)

K(2X)

STEP 3. INSTALLING THE EXTERIOR ASSEMBLY

3.1: To secure Exterior

Assembly of lock, peel the

cover off the adhesive strips

3.3: Place the exterior assembly on the door by inserting the torque blade on a vertical

position to the deadbolt slit hole + and guide the cable under the deadbolt. Secure and

fastened with the adhesive strips.

3.2: Before placing the exterior assembly on the

door, make sure the torque blade is in vertical

position and the deadbolt is extended.

EXTERIOR VIEW

(1)

Vertical

When installing the exterior assembly,

make sure the deadbolt is fully

extended and the slit hole is vertically

positioned on the bottom, the torque

blade should be inserted in a vertical

position.

STEP 4. INSTALLING THE INTERIOR ASSEMBLY

4.1: Peel of the cover

off the adhesive strip on

the mounting plate.

4.3: Without using any tools, insert 2

screws (G) on the side of the torque

blade. By using hand carefully, turn

the screws clockwise to catch the

thread, then counter clockwise to

make sure they are not cross threaded

and turns smoothly. Make five turns

before using a screw driver to tighten

the screws until the mounting plate is

securely placed to the door.

4.4: Before installing the interior

assembly, use the physical key and

try to unlock/lock to check if the

deadbolt is moving and not stuck. Do

not forget to take out the key before

proceeding to next steps.

4.2: Place the mounting plate on the

interior side of the door. Guide the cable

to the opening ear on the side of mounting

plate and make sure the torque blade is at

the center of the mounting plate.

G(2X)

Plug the cable that is coming

through the door into the Interior

lock. Make sure you match the

direction of the plug correctly and

matching the red side of

the plug with the red side on the

lock. Secure the connection by

ensuring the snap is inserted tightly.

In case you need to reinstall the lock

and disconnect the cable, make

sure to press the snap to release the

plug before carefully pulling it out.

Do not force to pull the plug as this

may result to lose connection and

damage the lock.

STEP 4. INSTALLING THE INTERIOR ASSEMBLY

4.6： Before placing the

interior assembly to the

mounting plate, ensure

the thumb turn is vertical.

4.5：

4.7: Place the interior

assembly against the

mounting plate and make

sure the torque blade is

inserted to the thumb turn

shaft.

4.8 Secure the interior

assembly with 2 screws (I)

I（2X）

RESET PROGRAM

5.1:

First install 3 of the 4 batteries. Before installing the last

battery, press and hold the PROGRAM button while

installing the last battery until you hear a beep from Lockly.

Lockly will then perform a self check and the keypad screen

will start to initiate. This self check will automatically determine

and set your door lock to a left open or right open door.

5.2:

After you checked that the lock manually lock and

unlock and deadbolt moves smoothly, Install the battery

cover with screw (H) and fastened.

The self-check process is very important step to ensure the installation is done properly.

After the lock finished the self-check, manually lock and and unlock your door by using the

thumb turn and the key to make sure the deadbolt moves smoothly. If you feel that there is

a tight tension while you are turning, it means that the lock may have not been installed

straight. Go back to Step 2 and re-install the lock.

To check if your lock was installed correctly, manually unlock your door by using the thumb

turn, then brush your hand across the screen on the outside. Your lock should lock the

deadbolt. If your lock automatically unlocks after it has been locked, it means that your

lock was installed incorrectly - proceed to Step 2 to make sure your lock was installed with

the deadbolt extended and the torque blade was inserted vertically while the deadbolt

was extended.

STEP 5. INSTALLING BATTERIES

PROGRAM RESET

Congratulations! You have completed the Lockly Vision installation.

To complete the setup of Lockly Vision smart lock and video doorbell, download the Lockly

App and follow on-screen instructions to complete your setup and installation.

Install the door strike.

Install the door strike to your door frame and

proceed to the last step of installation of your

new lock. You may use our supplied door

strike or use your existing door strike as long as

the dead bolt moves smoothly in and out of

the door strike.

As there are many types of doors, you may

need to make slight adjustments so the dead

bolt moves smoothly. If anything is rubbing

against the deadbolt when locking and

unlocking, you may experience a warning

sound (rapid beeping) indicating that the lock

is experiencing misalignment or something is

blocking the deadbolt.

K(2X) N

STEP 6: INSTALLING THE DOOR STRIKE

Scan or visit Lockly.com/app

Altri manuali per Vision

Indice

Altri manuali Lockly Serratura della porta

Lockly

Lockly SECURE LUX MORTISE EDITION Manuale utente

Lockly

Lockly Secure LUX Manuale utente

Lockly

Lockly DEADBOLT EDITION 7S Manuale utente

Lockly

Lockly FLEX TOUCH PRO Manuale utente

Lockly

Lockly ACCESS TOUCH PRO Manuale utente

Lockly

Lockly DEADBOLT EDITION 7S Manuale utente

Lockly

Lockly DEADBOLT EDITION SECURE PGD728 Manuale utente

Lockly

Lockly LUX COMPACT PGD688FSN Manuale utente

Lockly

Lockly MORTISE EDITION SECURE LUX PGD829AFUS Manuale utente

Lockly

Lockly LATCH EDITION SECURE PLUS Manuale utente

Lockly

Lockly SECURE PLUS Manuale utente

Lockly

Lockly LUX COMPACT PGD688F-MB Manuale utente

Lockly

Lockly FLEX TOUCH Manuale utente

Lockly

Lockly DEADBOLT SECURE PLUS Manuale utente

Lockly

Lockly FLEX TOUCH Manuale utente

Lockly

Lockly LATCH EDITION SECURE PGD628 Manuale utente

Lockly

Lockly DEADBOLT SECURE PLUS Manuale utente

Lockly

Lockly SECURE PRO Manuale utente

Lockly

Lockly LATCH EDITION 6S Manuale utente

Lockly

Lockly SECURE PRO Manuale utente

Lockly

Lockly LUX Compact Manuale utente

Lockly

Lockly PGD728F Manuale utente

Lockly

Lockly DEADBOLT EDITION PGD1128 Manuale utente

Lockly

Lockly DEADBOLT EDITION PGD1128FPW Manuale utente

Manuali Serratura della porta popolari di altre marche

Assa Abloy

Assa Abloy effeff 827A-IP Manuale utente

We.lock

We.lock SECBNEBL51 Manuale utente

Iseo

Iseo MA1A Manuale utente

ID Lock

ID Lock 150 Manuale utente

iLoq

iLoq G50S Manuale utente

SDC

SDC Z7835 Manuale utente

ilco

ilco 452 Manuale utente

Samsung

Samsung shs-h705 Manuale utente

TRU-BOLT

TRU-BOLT 08102017 Manuale utente

CDVI

CDVI 500-LADJ Manuale utente

Igloohome

Igloohome Deadbolt 2S Metal Grey Istruzioni di installazione e manutenzione

eSSL

eSSL FL-300 Manuale utente

JAKO

JAKO JKBTNX4 Manuale utente

Dorma

Dorma MUNDUS PREMIUM GK 50 Guida utente

SCOOP

SCOOP Pullbloc 4.1 FS Panik Manuale utente

Yale

Yale MORTISE 8800 SERIES Manuale utente

Siegenia

Siegenia KFV AS3500 Manuale utente

Saflok

Saflok Quantum ädesē RFID Manuale utente