logika Smart Door Guardian Manuale utente
© 2019 Logika Limited
Smart Door Guardian
WL-ZSPDBMA-PI13-01
Product Manual
Version 1.0
1
Logika Limited
E
-Centre, Massey University, Gate 5, Oaklands Road
Albany, Auckland 0632, New Zealand
www.logika.nz
·support@logika.nz
Introduction
Thank you for choosing Logika. Please take a moment to carefully read through the manual to
ensure safe and proper installation and use.
•Before use, the product must be properly installed as described in this manual by a qualified
technician.
•The product should be used with the supplied accessories.
•Do not disassemble or modify the product.
•Logika is not responsible for any loss due to improper installation or use of this product.
•Please visit our official website at www.logika.nz for more information.
•You can also contact us at the following email address: suppo[email protected].
2
Packing List
3
Device Layout
Infrared Night Vision
Photosensitive Detection
HD Camera
PIR Motion Detection
Door Peephole
Microphone
Doorbell Button
Speaker
Peephole Cover
Battery Cover Release Switch
Speaker
Status Indicator
TF Card Slot
WIFI Settings Button
Power Switch
Charging Indicator
Micro USB Charging Port
4
Features
•Communication Mode: IEEE 802.15.4 Zigbee.
•A hybrid of traditional door peephole and smart camera.
•The doorbell sends alerts to the mobile app, allowing remote access.
•Smart camera:120° wide angle HD video; Supports remote access and video calling or voice
intercom.
•Night vision: 120° infrared light.
•Motion detection: Take video recording for 10 seconds when people approach within 2
meters and linger for a pre-set time; Push notification and video to mobile phone
immediately.
•Low power consumption and ultra-long battery life.
Specifications
Resolution 720p
Focal Length 1.25mm
Lens Material Optical Glass
Camera's Field of View 83 deg Horizontal 120 deg Vertical
Infrared Night Vision Supported
Storage TF Card Storage (Max 32GB)
Motion Detection Distance Max 3m
Net Weight 555g
Size
Front Plate: 76mm*27mm
Back Plate: 80mm*159mm
Material Zinc Alloy + ABS + PC
Suited Door Thickness 35-90mm
Power Parameter DC 4.2V Lithium Battery (3000mA)
Power Supply DC 5V 1A
Standby Power Consumption 1.4W
Temperature for Working -10°C-+45°C
Humidity for Working ≤95%RH (Noncondensing)
Flame Retardant Rating UL94 V-2
5
Installation Steps
Hardware Installation
1) Remove the film from the 3M double-sided tape on the front plate, pass the cylinder
through the hole in the door, along with the data cable, and affix to the door.
2) Pass the data cable through the hole on the fixed plate and screw the plate onto the door.
3) Connect the data cable to the connector on the back plate.
4) Attach the back plate to the fixed plate by mounting it on the small hooks.
5) Connect the battery to the back plate. Charge the battery via the micro USB connector if
required.
Front Plate
Fixed Plate
Data Line
Back Plate
M3*8
Battery
Door
M3*35 (Select different screws based on the
actual door thickness
)
6
Adding the Device to the Smart Home Network
Use the Logika Smart Home app to add the device to the Smart Home system. Please refer to the
Logika Smart Mobile App user guide which will take you through the process of adding smart
devices to the system.
Refer to the information below to locate the device in the Device Add screen. Once selected, the app
will walk you through how to add the device to the system.
Device Category:
Camera
Device Name:
Smart Door Guardian
7
Device Functions
Perform a Factory Reset
Press and hold the WIFI Settings button (You will need a paperclip or other small pin to poke through
the hole to the switch inside). Wait for the vocal response “Factory setting restored” from the
device, then release the button.
Follow instructions from with the mobile app to connect the device to the network.
Safety Precautions
•
Do not press hard on the clear dome cover or Infrared Night Vision sensor (convex black
dome) on the front panel as this may cause damage.
•
Be careful when feeding the data cable through to the other unit and make sure the
connectors are safely seated in their respective ports.
•
Use the supplied power adaptor and USB cable to charge the battery.
•
Do not expose the device to high temperatures, excessive rain, high humidity or dusty
areas.
8
Troubleshooting
The device cannot be added to the Zigbee network.
The device may be registered to another network. In rare occasions this can happen if the device
was not removed from the test network at the factory.
Perform the Perform a Factory Reset procedure mentioned in Device Functions section to clear this
setting. You should now be free to add the device to the local smart network.
The issue you are experiencing is not mentioned here.
Please contact us at support@logika.nz with your issue and we will do our utmost to help!
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali logika Sistema di sicurezza
Manuali Sistema di sicurezza popolari di altre marche
EDM
EDM Solution 6+6 Wireless-AE Manuale utente
Highway Safety Group
Highway Safety Group EA401 Manuale utente
Siren
Siren LED GSM Manuale utente
Detection Systems
Detection Systems 7090i Istruzioni per il montaggio
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuale utente
Siemens
Siemens FDM273 Manuale utente