Logitech PRO X Wireless LIGHTSPEED Dimensioni
PRO X Wireless LIGHTSPEED FAQs 1
PRO X Wireless LIGHTSPEED Gaming Headset
INDEX
GETTING STARTED
●Contents
●Features
●Headset setup
●Headset operation
SPECIFICATIONS
●Product Information
●Compliance
●Product Dimensions
●General Product Specifications
●Headset Specifications
FAQs
●Pair your PRO X 2 or PRO X headset to a new LIGHTSPEED wireless adapter
●How to customize surround sound with Logitech G HUB
●Logitech G HUB - FAQs
○About Logitech G Hub
WARRANTY
●Hardware warranty
PRO X Wireless LIGHTSPEED FAQs 3
GETTING STARTED
CONTENTS
PRO X Wireless LIGHTSPEED FAQs 4
FEATURES
1. Microphone mute toggle
2. Volume wheel
3. Power switch
4. USB C charging port
5. Microphone
PRO X Wireless LIGHTSPEED FAQs 5
HEADSET SETUP
1. Connect microphone to headset
2. Plug receiver into USB port
3. Turn on power switch
4. Download and install optional software
PRO X Wireless LIGHTSPEED FAQs 6
HEADSET OPERATION
Microphone mute toggle
●Microphone is active when red is not visible. Microphone is muted when red is visible.
Volume wheel
●Rotate up to increase OS volume. Rotate down to decrease OS volume.
Power switch
●Power is on when cyan is visible. Power is off when red is visible. Headset will power
down automatically after 30 minutes of no audio to save battery life. To resume use,
turn the power off, then back on again. Timeout value can be adjusted in G HUB.
USB C charging port
●Use provided USB A to USB C charging cable to charge headset by plugging into USB
port on PC. Cable is for charging and firmware update only – audio will not play over
wired connection.
Microphone
●For optimal voice pickup, place foam ball approximately two fingers’ width from the
corner of your mouth. Blue VO!CE functionality can be enabled using G HUB software.
PRO X Wireless LIGHTSPEED FAQs 7
SPECIFICATIONS
Product Information
Component
Model Number (M/N)
M/N Location
Headset
A00130
Under left ear pad
Receiver
A-00080
Bottom of the USB receiver
Compliance
Document
Link
Certificates
Please contact Customer Service
Battery MSDS
Please contact Customer Service
Product Dimensions
Component
Height
Length
Width
Weight
(without
cable)
Charging
Cable Length
Headset
7.67 in
(195 mm)
w/o mic
boom
5.43 in
(138 mm)
w/o mic
boom
3.70 in
(94 mm) w/o
boom
370g with
mic boom
1.8m
(6.56 ft)
Receiver
0.33 in
(8.4 mm)
0.75 in
(19 mm)
2.28 in
(58 mm)
0.28 oz
(9 g)
N/A
PRO X Wireless LIGHTSPEED FAQs 8
General Product Specifications
At Release
Software Available
Logitech G HUB
OS/Platform Support
Windows® 7 or later
System Requirements
USB 2.0 Port and internet connection for
optional software download
Headset Specifications
Connection Type
USB
USB VID & PID
VID_046D & PID_0ABA
USB Protocol
2.0
USB Speed
High Speed
Headphone Type
Circumaural
Driver Type
Hybrid mesh PRO-G
Driver Size
50 mm
Headphone Sensitivity
91.7dB @ 1 mW & 1 cm
Headphone Frequency
Response
20 Hz-20 kHz
Input Impedance
32 ohm
Magnet
Neodymium
Microphone Size
6mm
Microphone Pickup
pattern
Unidirectional / Cardioid
Microphone Type
Electret Condenser
PRO X Wireless LIGHTSPEED FAQs 9
Headset Specifications
Microphone Frequency
Response
100Hz to 10 kHz
Earcup Audio Controls
Microphone mute
Rotary volume control
Power switch
Wireless Connection
Type
2.4 GHz LIGHTSPEED
Wireless Range
Up to 15 m
Other Features
BLUE VO!CE microphone technology
DTS Headphone:X 2.0
Removable earpads
1 x leatherette earpads
1 x velour earpads
Battery Life
(Rechargeable)
Up to 20 hours*
*Battery life may vary based on user and computing
conditions. Up to 20h battery life is based on headset volume
set to 50%.
PRO X Wireless LIGHTSPEED FAQs 10
FAQs
●Pair your PRO X 2 or PRO X headset to a new LIGHTSPEED wireless adapter
If your device becomes unpaired or you receive a replacement LIGHTSPEED wireless adapter,
do the following to pair your device:
1. Plug in the LIGHTSPEED wireless adapter.
2. Insert a pin into the reset port on the LIGHTSPEED wireless adapter to initiate pairing
mode. The light on the adapter will blink.
3. Turn on the headset.
4. Remove the left ear pad on the headset.
5. Insert pin into pin-hole located below the speaker driver and between the lower two
screws. The headset will blink and chime.
6. Wait 10-15 seconds for pairing to complete — blinking stops on both the headset and
adapter and you'll hear a chime in the headset to indicate pairing is complete.
●How to customize surround sound with Logitech G HUB
You can use Logitech G HUB to customize surround sound settings on your Logitech G audio
device.
NOTE: Make sure you're using the latest version of G HUB before you connect your Logitech G
audio device to the computer. You can download the latest version of G HUB from the
Download tab of your product's support page.
Indice
Altri manuali Logitech Cuffia
Logitech
Logitech 981-000056 - PlayStation 3 Vantage USB... Manuale utente
Logitech
Logitech H151 Manuale utente
Logitech
Logitech ZONE WIRELESS Manuale utente
Logitech
Logitech ZONE WIRELESS Manuale utente
Logitech
Logitech H390 Manuale utente
Logitech
Logitech G432 Manuale utente
Logitech
Logitech Ultimate Ears 200vm Manuale utente
Logitech
Logitech ZONE 900 Manuale utente
Logitech
Logitech G930 Manuale utente
Logitech
Logitech G432 Manuale utente
Logitech
Logitech G633 Artemis Spectrum Manuale utente
Logitech
Logitech H390 Istruzioni di montaggio
Logitech
Logitech 980228-0403 - Mobile Freedom - Headset Manuale utente
Logitech
Logitech A-00031 Manuale utente
Logitech
Logitech PRO X Manuale utente
Logitech
Logitech 980130-0403 - Premium USB Headset 300 Istruzioni operative e di sicurezza
Logitech
Logitech S150 - Digital USB PC Multimedia Speakers Manuale utente
Logitech
Logitech G332 Manuale utente
Logitech
Logitech ZONE 950 Manuale utente
Logitech
Logitech Stereo H650e Manuale utente
