Longshine FS6108 Manuale utente

Longshine

Technologie Europe GmbH

www.longshine.de

5/8-Port 10/100Mbps

Fast Ethernet Switch

User’s Manual

English

Deutsch

Spanisch

Französisch

Italienisch

Polski

Introduction

The device is a powerful, high-performance Fast

Ethernet switch, with all ports capable of 10 or

100Mbps auto-negotiation operation (NWay),

which means the switch could automatically

negotiate with the connected partners on the

network speed and duplex mode. It is ideal for

micro-segmenting large networks into smaller,

connected subnets for improved performance,

enabling the bandwidth demanding multimedia

and imaging applications. Compared to the

shared 10Mbps or 100Mbps networks, the switch

delivers a dedicated 10/100Mbps connection to

every attached client with no bandwidth

congestion issue. This switch also supports auto

MDI / MDI-X function. Each port could be used to

connect to another switch or hub with no

crossover RJ-45 cable.

Store-and-forward switching mode promises the

low latency plus eliminates all the network errors,

including runt and CRC error packets. To work

under full-duplex mode, transmission and

reception of the frames can occur simultaneously

without causing collisions as well as double the

network bandwidth.

The switch is plug-n-play without any software to

configure and also fully compliant with all kinds of

network protocols. Moreover, the rich diagnostic

LEDs on the front-panel can provide the operating

status of individual port and whole system.

Before you start to install the switch, check the

following contents in this package：

 One NWay switch

 One external power adapter

 User’s manual

LED Definition

Please refer to the following table for LED

definition

5port

8port

LED Status Operation

Steady

Green

Power is onPower

Off Power is off

Steady

Green

The port is connected

Blinking

Green

The port is

transmitting/receiving data.

Link/Act

Off No connection

Rear Panel

5port

8port

Stations Connection

Connect each station to the switch by twisted-pair

cable. Plug one RJ-45 connector into a RJ-45 port

of the switch, and plug the other RJ-45 connector

into the station’s network adapter. Power on the

switch and then system is ready.

For cable selection, refer to the following table.

The switch supports port-based QoS as the

following table:

Model High-priority

ports

Low-priority

ports

5-Port Model: Port 1, 2 Port 3, 4 and 5

8-Port Model: Port 1, 2 and 3 Port 3, 4, 5, 6, 7

and 8

The bandwidth ratio of high priority port to low

priority port is 16:1.

Switches Connection

In making a switch interconnection, you could use

any port to connect another switch with straight or

crossover cable. As all the ports support auto MDI

/ MDI-X function, using a straight cable to make a

switch-to-switch connection is allowed.

For cable selection, refer to the following table：

Network Speed Cable Type Max. Length

10Mbps Cat. 3, 4, 5

UTP/STP 100 meters

100Mbps Cat. 5 UTP/STP 100 meters

Specification

Standard IEEE 802.3 10BASE-T

IEEE 802.3u 100BASE-TX

IEEE 802.3x full duplex operation and

flow control

Interface 5* 10/100Mbps RJ-45 Fast Ethernet

Ports

8* 10/100Mbps RJ-45 Fast Ethernet

Ports

Uplink Auto MDI/MDI-X（Auto crossover）

Network

Speed

10/100Mbps & Full/Half duplex mode

auto detection

MAC

Address

Table

1K MAC address entries

Memory 512 K bits (5port)

768 K bits (8port)

Power

Supply

External Power adapter

5VDC 0.6A

EMI CE, FCC and VCCI class B

FCC Certifications

This Equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when

the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in

accordance with the instruction manual, may cause

harmful interference to radio communications.

Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be

required to correct the interference at his own expense.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1)

this device may not cause harmful interference, and (2)

this device must accept any interference received;

including interference that may cause undesired operation.

CE Mark Warning

This equipment complies with the requirements relating to

electromagnetic compatibility, EN 55022 class B for ITE,

the essential protection requirement of Council Directive

89/336/EEC on the approximation of the laws of the

Member States relating to electromagnetic compatibility.

Company has an on-going policy of upgrading its products

and it may be possible that information in this document is

not up-to-date. Please check with your local distributors for

the latest information. No part of this document can be

copied or reproduced in any form without written consent

from the company.

Trademarks:

All trade names and trademarks are the properties of their

respective companies.

Einleitung

Das Gerät ist ein leistungsstarker,

hochleistungsfähiger Fast Ethernet Switch, bei

dem alle Ports zu der 10 oder 100 Mbps

Auto-Negotiation Operation (Nway) fähig sind.

Das heißt, dass der Switch automatisch mit den

verbundenen Partnern im Netzwerk

Geschwindigkeit und Duplex Modus verhandeln

kann. Es ist ideal, um größere Netzwerke auf

kleinere, verbundene Subnetzwerke zu verteilen,

um so die Leistung zu verbessern und die

Bandbreite, die für Multimedia und

Image-Applikationen erforderlich ist, zu

ermöglichen. Im Vergleich zu den gemeinsam

benutzten 10 Mbps oder 100 Mbps Netzwerken,

bietet dieser Switch eine zuverlässige

10/100Mbps Verbindung zu jedem verbundenen

Client ohne Stauungsprobleme. Dieser Switch

unterstützt auch die Auto MDI / MDI-X Funktion.

Jeder Port könnte für die Verbindung zu einem

anderen Switch oder Hub ohne Crossover RJ-45

Kabel benutzt werden.

Der Store & Forward Switching Modus verspricht

niedrige Latenzzeiten und eliminiert alle

Netzwerkfehler, inklusive kleiner Fehler und CRC

Fehlerpaketen. Um in dem Full-Duplex Modus

arbeiten zu können, ist der gleichzeitige Empfang

und das Versenden von Frames möglich, ohne

dass dabei Kollisionen entstehen sowie die

Verdopplung der Netzwerk Bandbreite.

Der Switch ist komplett Plug & Play fähig und es

wird keine Software für die Konfiguration benötigt.

Außerdem werden alle möglichen

Netzwerkprotokolle unterstützt. Darüber hinaus

informieren die Anzeige-LEDs auf der Frontseite

über den Funktionsstatus der einzelnen Ports und

des gesamten Systems.

Bevor Sie damit beginnen, den Switch zu

installieren, überprüfen Sie bitte den folgenden

Inhalt des Paketes:

 Ein NWay Switch

 Einen externen Spannungsadapter

 Bedienungsanleitung

LED Definition

Bitte beziehen Sie sich auf die folgende Tabelle

für die LED Beschreibung

5 Port

8 Port

LED Status Operation

Dauerh.

grün

Spannung eingeschaltetPower

Aus Spannung ausgeschaltet

Dauerh.

grün

Der Port ist verbunden

Blinkend

grün

Der Port sendet / empfängt

Daten.

LINK /

ACT

Aus Keine Verbindung

Rückseite

5 Port

8 Port

Indice

Lingue:

Altri manuali Longshine Router di rete

Longshine

Longshine IR2114D Manuale utente

Longshine

Longshine GS7104 Manuale utente

Longshine

Longshine LCS-883R-SW24N Manuale utente

Longshine

Longshine LCS-IR-3114P Manuale utente

Longshine

Longshine LCS-883R-DSL-4FN Manuale utente

Longshine

Longshine FS9116C Manuale utente

Longshine

Longshine LCS-GFS9326 Manuale utente

Longshine

Longshine LCS-GSP8108 Manuale utente

Longshine

Longshine FS8116B Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza