Lorex ACC1721HB Manuale utente

QUICK START GUIDE

English Version 1.0

ACC1721HB

DAC1721, DAC1721HB

MODELS:

As our products are subject to continuous

improvement, Lorex Technology Inc. reserves the

right to modify product design, specifications and

prices, without notice and without incurring any

obligation. E&OE

NEED HELP?

ACC1721HB

For customer support call:

1-888-425-6739 option 1, 1

DAC1721, DAC1721HB

For customer support call:

1-866-344-4674

*Heater and Blower on ACC1721HB and DAC1721HB models only.

Specifications

WEATHERPROOF

CAMERA ENCLOSURE

WITH HEATER AND

BLOWER*

ENCLOSURE

HEATER & BLOWER*

Wall Mount Bracket

Precautions:

• Use a UL/CSA approved 24V AC power supply**

• Use an appropriate low voltage power cable to

prevent fire or electrical shock

• Make sure to install the camera in an area that

can support the camera weight.

• There are no user serviceable parts inside the

enclosure. Please do not disassemble the

enclosure

• Do not clean the lens cover with an abbrasive

cleaning material—please use a soft cloth to

clean the lens cover

• This housing is not recommended for use with

cameras featuring IR LEDs, due to the potential of

reflection

*Heater and Blower on ACC1721HB and DAC1721HB models only.

**24V AC power supply required by ACC1721HB and DAC1721HB models

only.

Weatherproof Rating IP66

Enclosure Dimensions

(WxDxH)

142 mm x 370 mm x 115 mm /

5.6” x 14.6” x 4.5”

Enclosure Window

Dimensions (WxH)

74 mm x 63 mm /

2.9” x 2.5”

Power Requirement 24V AC/ 9W

Heater Operation Level On: 15°C ±3°C / 59°F ±5.4°F

Off: 25°C ±3°C / 77°F ±5.4°F

Blower Operation Level On: 35°C ±3°C / 95°F ±5.4°F

Off: 25°C ±3°C / 77°F ±5.4°F

Bracket Length 205 mm / 8.1”

Maximum Supported Weight 22 lbs. / 10 kg

Swivel Angle up to 360°

To install the camera in the housing (cont’d.):

2. Place the camera and base in the enclosure. Use the

included screws to fix the camera in place (see Figure

2.0).

3. Pass the cables (power and video) through the conduit

cap. Push the cables through the membrane of the

rubber stopper in the conduit plug. Pass cables through

the duct on the bottom of the housing.

4. Screw the conduit cap onto the plug loosely (you can

tighten once the cables are connected).

5. Insert the complete conduit plug into the duct on the

bottom of the housing. The conduit plug should snap

firmly into place. If you have model DAC1721, go to step

7. If you have models ACC1721HB or DAC1721HB, go

to step 6.

6. ACC1721HB, DAC1721HB models only—Use a

screwdriver (not included) to connect the 24V/AC, non-

polarized wiring to the power input on the thermostat

control board (see Figure 3.0). Tighten the conduit cap

firmly to prevent moisture and dust from entering (see

Figure 4.0).

7. Close the enclosure firmly and adjust the bracket

until you have the camera and housing in the

desired position. If desired, use a standard lock

(not included) to lock the housing.

Figure 3.0 Connect wires (x2) to power input terminals

Figure 4.0 Feed cables through duct and tighten cap

Contents Assembling the housing

1 x Screw Kit

1 x Weatherproof Enclosure

To assemble the housing:

1. Mount the wall bracket using the provided screw kit.

Note: Make sure you have drilled any necessary holes

in your mounting surface and run sufficient lengths of

extension cables (not included) for your camera (not

included).

2. Use the included screws to attach the enclosure to the

mounting bracket.

To install the camera in the housing:

1. Open the enclosure and remove the camera base.

Use the included screws to attach the camera to the

base.

Figure 1.0 Enclosure base

Figure 2.0 Place camera in enclosure

• Aluminum-coated housing

• Ideal for Indoor/Outdoor use

• Built-in Heater & Blower for use in various

climates*

• Lockable enclosure keeps your CCTV

investement safe**

• Includes metal wall-mount bracket

Accessories:

• Corner Bracket—MNT1721C

• Pole Bracket—MNT1721P

*Heater and Blower on ACC1721HB and DAC1721HB models only.

**Requires optional lock.

1 x Metal Wall-Mount Bracket

Installing the camera

Features:

ATTENTION - Make sure you have tested the camera

(not included) prior to selecting a permanent mounting

location by temporarily connecting the cameras and

cables to the TV,VCR, DVR or Observation System.

1 x Conduit Cap (a)

1 x Rubber Stopper (b)

1 x Conduit Plug (c)

(b)

(c)

(a)

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Lorex Accessori per fotocamere

Lorex

Lorex ACBATTR3 Series Manuale utente

Manuali Accessori per fotocamere popolari di altre marche

Viltrox

Viltrox EF-NEX Istruzioni per l'installazione

Calumet

Calumet 7100 Series CK7114 Manuale utente

Ropox

Ropox 4Single Series Manuale utente

Cambo

Cambo Wide DS Digital Series Istruzioni operative

Samsung

Samsung SHG-120 Manuale utente

Ryobi

Ryobi BPL-1820 Manuale operativo

Aegis

Aegis ABL-36020P Manuale utente

Pentax

Pentax Data Back Fc Manuale utente

Fantasea

Fantasea EyeGrabber F Series Manuale utente

Honeywell

Honeywell HDZ20HD Manuale utente

EGO

EGO BA1400T Manuale utente

Sima

Sima SRW-62 Manuale utente

Shape

Shape A7SSMKIT Manuale utente

Slide Kamera

Slide Kamera HST-2 Manuale utente

Power works

Power works 2902613 Manuale utente

SES

SES SE-2047-2 Manuale utente

Olympus

Olympus PT-EP05L Manuale utente

Starlite

Starlite OctoDome nxt Manuale utente