Louvolite Roller Duo Roll Manuale
Roller Duo Roll
Fitting and Operating Instructions
Roller Duo Roll
Fitting and Operating Instructions
Roller Duo Roll
Fitting and Operating Instructions
Carefully unwrap the roller blind and its associated brackets.
The end brackets are universal and can be xed in a top, face or side x position.
The intermediate brackets can be either top or face x only.
Note – Duo link tting can only be used on system 40 and 45.
FITTING THE BRACKETS
Secure a control end bracket on the right hand side of the blind. Measure from
this bracket to a point the same distance as the width of blind number 1 and mark
the position.
Secure an intermediate bracket at this point ensuring the outside face of the
intermediate bracket lines up with the marked position.
Now measure and mark the distance from this intermediate bracket to the end
bracket on the left hand side of the blind and secure a control end bracket.
FITTING THE BLIND
NOTE: The right hand side blind must be tted rst.
With the fabric rolled around the tube insert the male idle end plug on the right
hand blind through the intermediate bracket. With this in place offer the control
end to the control end bracket and secure the blind in place ensuring the centre
lug has dropped into the bracket.
With the fabric wrapped around the tube on the left hand side blind, insert the
female idle end of the left hand side blind into the male idle end plug of the right
hand side blind. With this in place offer the control end of the left hand side blind
to the control end bracket and secure the blind in place ensuring the centre lug
has dropped into the bracket.
Roller Duo Roll
Fitting and Operating Instructions
Easybreak® Connector
200mm apart
CHILD SAFETY
Your blind will be supplied with either Easybreak® connectors attached to the
operating chain or a cord tidy that will need to be tted to the wall.
Easybreak® System
Two Easybreak®connectors are connected to the operating chain 200mm apart.
This ensures that at least one of them will be in the vertical position ensuring they
perform as required.
If excessive weight is applied within the loop an Easybreak®connector will break
apart.
If an Easybreak® connector comes apart then it will need to be re-connected.
To re-connect, check the Easybreak® connector for damage. If undamaged,
re-connect the chain by inserting the last ball on the end of the chain into the larger
hole of the connector and push it into place.
Tensioned System using cord tidy.
If the blind is tted with a continuous loop chain then a cord tidy will be attached
to the chain. This must be tted to the wall as follows:
Fitting a side x cord tidy.
The cord tidy is a two piece device and will arrive with a disposable red tab tted
to it.
Roller Duo Roll
Fitting and Operating Instructions
Roller Duo Roll
Fitting and Operating Instructions
Remove the disposable red tab by disengaging it from the chain and then pull
out the disposable red tab.
Position the cord tidy to the wall at the furthest distance below the roller tube
adding appropriate tension to the chain and mark its location.
Disposable retaining thrust washer
Disposable red tab
Disposable red tab
Cord tidy
Roller Duo Roll
Fitting and Operating Instructions
Split the cord tidy and mark the remaining offset hole position
before drilling and plugging both location holes if necessary.
Screw into the offset hole to x the back piece of the cord tidy to the wall.
Re-assemble the cord tidy with the chain and x it in previously marked position
with a screw through the centre hole.
Roller Duo Roll
Fitting and Operating Instructions
Roller Duo Roll
Fitting and Operating Instructions
Cover cap
Push t a cover cap over the screw hole opening.
Roller Duo Roll
Fitting and Operating Instructions
Fitting a face x cord tidy.
Position the face x cord tidy to the wall at the furthest distance below the
headrail adding appropriate tension to the chain and mark its location.
Mark the remaining hole position before drilling and plugging both location holes
if necessary.
Roller Duo Roll
Fitting and Operating Instructions
Roller Duo Roll
Fitting and Operating Instructions
Attach the cord cover plate with the screw provided.
Push t a cover cap over the screw hole opening.
Cover cap x 3
Roller Duo Roll
Fitting and Operating Instructions
OPERATING THE BLIND.
For a conventional roller blind, in order to lower the blind, pull the rearmost length
of chain downwards with a smooth and steady pressure. To roll the blind up do the
same on the front length of chain.
For a reverse roll blind the opposite is true, to lower use the front chain and to raise,
use the rear chain.
NOTE TO INSTALLER:
Please ensure a general child safety warning tag is tted on the product.
Notes
Indice
Altri manuali Louvolite Tenda per finestra
Louvolite
Louvolite SC Series Manuale
Louvolite
Louvolite Roller System 32 Manuale
Louvolite
Louvolite Perfect Fit Manuale utente
Louvolite
Louvolite R4045 Manuale utente
Louvolite
Louvolite Vision 32 Open Cassette Istruzioni operative
Louvolite
Louvolite One Touch 1100 Series Manuale utente
Louvolite
Louvolite R1705 Manuale di istruzioni
Louvolite
Louvolite Perfect Fit Manuale utente
Manuali Tenda per finestra popolari di altre marche
Domondo
Domondo PureNight Manuale di istruzioni per l'installazione
rollease acmeda
rollease acmeda Easy Spring Air Guida all'installazione
IKEA
IKEA KADRILJ Manuale utente
Hallis Hudson
Hallis Hudson Rolls Super glide Manuale utente
Benthin
Benthin P1614 Manuale utente
MV LINE
MV LINE CLARA 015 Manuale di istruzioni
