Lowell MAT-1 Data Logger Manuale utente
BTK1 Battery Replacement Tool Kit, Rev G Page 1 of 7
TCM & MAT Data Logger Battery Replacement Instructions
These instructions apply to the
following products:
• MAT-1 Data Logger
• TCM-1 Current Meter
• TCM-2 Wave and Current Meter
• TCM-3 4500m Current Meter
The instructions assume that the user
has purchased the MAT-1 Battery
Replacement Tool Kit.
Materials:
•Circuit Board Holding Tool
•3/32” Hex Driver
•Replacement “A” size lithium battery
•Replacement desiccant packs (optional)
Caution: This logger is sensitive to static electricity when removed from the logger housing.
Hold the circuit board by the edges and avoid working on indoor carpet or in other static prone
environments.
Important: For loggers with serial numbers not between 2004043-2004058, and lower than 2006000,
the lithium metal batteries should be tested and conditioned prior to deployment. Conditioning is
necessary to ensure that the battery has not become passivated during storage. (Passivation is a
temporary build-up of resistance in the battery that prolongs its storage life, but reduces peak currents.)
Conditioning is performed by running the battery briefly prior to field deployment. See Steps 14-17. If you
are unsure whether this applies to your device, please go to Step 19: Identifying a Newer Model, after
you have completed steps 1-7.
General Instructions
1. Remove the end cap of the logger, connect a USB cable and use Domino to stop the logger.
Failure to stop a running logger will result in data loss.
2. Slide the Circuit Board Holding Tool into the end of the logger. Aligning the slot in the tool with
the circuit board.
3. Locate the two hex screws inside the logger and insert the hex driver into one of them.
4. Loosen, but do not remove the screw. Repeat on the other side.
Align Circuit Board Holding
Tool and insert fully into
logger housing.
Carefully use the Hex Driver to
loosen set screws located inside the
logger (see next page).
BTK1 Battery Replacement Tool Kit, Rev G Page 2 of 7
5. The board should now be loose within the housing. Gently tap the housing and slide the circuit
board and battery out of the logger.
6. Disconnect the old battery by gently pulling on the battery leads. You may need to use a pair of
pliers to gently rock the plug back and forth.
7. Inspect the desiccant. Replace or refresh the
desiccant if not bright blue. To refresh desiccant,
warm it with an electric toaster oven or hot plate
at 100 C (210 F) for 20-30 minutes. Alternatively,
microwave it for a few seconds at a time until it is
bright blue.
The following instructions apply only to loggers with
serial numbers not between 2004043-2004058, and
lower than 2006000. If your logger is a newer model,
proceed to Step 19: Newer Models. Note: you can
identify a newer model visually as well. Instead of two desiccant packs, it will have one, and it
has a large blue capacitor on the opposite side of the circuit board (see step 19).
8. The logger must completely power down for a clean restart. Wait at least 3 minutes between
disconnecting the old battery and reconnecting the new battery for the on-board capacitors to
discharge.
9. Connect the new battery by gently pushing the polarized connector into the battery socket.
Verify that the green and red LED’s flash three times. If not, disconnect the battery, wait 3
minutes and repeat.
10. Carefully slide the battery, circuit board holder, desiccant and circuit board back into the logger
housing. It may take a couple of attempts to get the hang of it. Do not use force. Gently push
the board all the way into the housing using the Circuit Board Holding Tool.
11. Use the hex driver to tighten the hex screws. Alternate sides and do not over torque. (Use four
fingers, not your whole arm!)
Battery
Connector
Battery
Desiccant pack(s)
USB Port
Circuit Board
Holder
Set Screws (2)
Usable
Exhausted
BTK1 Battery Replacement Tool Kit, Rev G Page 3 of 7
12. Reconnect the USB cable and open the Device tab in Domino.
13. Verify that the “Logger Time” has reset to the year 2000, that the battery voltage is higher than
3.5V, and that the “Real-time Data” is updating. If any of these are not true, then the logger was
not fully reset and the logger must be power-cycled again. Go back to step 2 and increase the
time between disconnecting and reconnecting the battery. You should now reset the device
time to your computer time by clicking “Set Device Clock.”
IMPORTANT: You are not done yet. Perform a battery test run to test for, and to remove,
passivation of the lithium metal battery before starting a field deployment (see below).
Spot check
sensor readings
Verify the
battery voltage
is greater than
3.5V
Verify that the
logger’s clock
has reset
BTK1 Battery Replacement Tool Kit, Rev G Page 4 of 7
14. Perform a test run of the battery. An effective test will record at least 128 Kbytes of data with
the USB cable disconnected. To perform this test quickly, set the logger to run at 64Hz as shown
below and save the setup file:
15. Start the logger, disconnect the USB cable, wait 2.5 minutes and then check to see if the red LED
is on (firmware version 1.0.xx) or is blinking (firmware version 1.8.xx).
16. If the red error LED is indicating, reconnect the USB cable, stop the logger, disconnect the USB
cable and wait 5 minutes. Then repeat step 14-15. Repeat up to three times as necessary until
the red LED does not come on after 2.5 minutes at 64Hz.
17. If only the green LED is blinking, reconnect the USB cable, save a new setup file with your
desired deployment settings (MAT.cfg), and deploy your logger.
18. If after three attempts the red LED continues to indicate a problem, then something else is
wrong. Contact technical support for advice.
BTK1 Battery Replacement Tool Kit, Rev G Page 5 of 7
Models with serial number between 2004043-2004058, or greater than 2006000. These newer
models have a supercapacitor on the circuit board which makes battery testing unnecessary.
Instead, you will perform a software reset.
19. Identifying a newer model:
20. Newer Models: there is no need to wait before connecting a new battery. Connect the battery
now, and replace the logger in its housing according to steps 10-12. Note: these models only
have one desiccant pack. Place the desiccant pack on the opposite side of the circuit board from
the capacitor (above). This ensures that the device is centered in the housing.
21. Connect the logger to your computer and open the Device tab in Domino.
22. Perform a software reset: hold down Control+Shift and click on the USB icon directly to the left
of “Connected on USB.” The logger should temporarily disconnect, and then reconnect. The
device time should then say that the year is 2000.
Newer model has large blue
capacitor on one side of the
circuit board
Older: go back to step 8
Newer: skip steps 8-18
BTK1 Battery Replacement Tool Kit, Rev G Page 6 of 7
23. Reset the clock to your computer time by clicking “Set Device Clock” and verify that the new
battery voltage is greater than 3.5 volts by looking at the “Real-Time Data” box.
24. Save a new setup file with your desired deployment settings in the “Setup” tab. Your logger
should now be ready for deployment!
25. Should you encounter any problems, please do not hesitate to contact technical support for
advice.
Hold Control+Shift and click here to
perform a software reset:
BTK1 Battery Replacement Tool Kit, Rev G Page 7 of 7
Support
Additional information is available on the Lowell Instruments web site. Please see:
http://www.lowellinstruments.com/support for the most up-to-date support information.
Warning: This logger contains a lithium battery. Do not cut open, incinerate, heat above 85°C
(185°F), or recharge the lithium battery. The battery may explode if the logger is exposed to
extreme heat or conditions that could damage or destroy the battery case. Do not dispose of
loggers or batteries in fire. Do not expose the contents of the batteries to water. Dispose of the
batteries according to local regulations for lithium batteries.
Contact Information
Lowell Instruments, LLC
82 Technology Park Drive
East Falmouth, MA 02536
U.S.A.
© 2014-2020 Lowell Instruments, LLC
Altri manuali per MAT-1 Data Logger
1
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Lowell Registratore di dati
