Lowrance StructureScan 3D Manuale utente

ENGLISH

StructureScan 3D

Transducer

Installation manual

www.simrad-yachting.com | www.lowrance.com

Preface

Warning: It is your sole responsibility to install and

use the instrument and transducer(s) in a manner that

will not cause accidents, personal injury or property

damage. Always observe safe boating practices.

Sonar performance: The accuracy of the sonar depth display can

be affected by many factors, including the type and location of the

transducer and water conditions. Never use this instrument to

gauge depth or other conditions for swimming or diving.

The choice, location, and installation of transducers and other

components of the system are critical to the performance of the

system as intended. If in doubt, consult your Navico dealer.

To reduce the risk of misusing or misinterpreting this instrument,

you must read and understand all aspects of the Installation and

Operation manuals. We also recommend that you practice all

operations using the built-in simulator before using this instrument

on the water.

Disclaimer: Navico Holding AS and its subsidiaries, branches and

affiliates disclaim all liability for any use of this product in a way that

may cause accidents, damage or that may violate the law.

Compliance Statements: The StructureScan 3D Transducer

complies with:

•CE under EMC directive 2014/30/EU

•The requirements of level 2 devices of the Radiocommunications

(Electromagnetic Compatibility) standard 2008

The relevant Declaration of Conformity is available at the following

websites under the StructureScan 3D Transducer documentation

section:

•http://www.lowrance.com/

•http://www.simrad-yachting.com/

Trademarks: Lowrance®and Navico®are registered trademarks of

Navico. Simrad®is used by license from Kongsberg.

This manual refers to the following Navico products: DownScan

Imaging™ (DownScan), DownScan Overlay™ (DownScan Overlay),

2Preface | StructureScan 3D Transducer

StructureScan®(StructureScan), and StructureScan®HD

(StructureScan HD).

Preface | StructureScan 3D Transducer 3

Check the contents

Included with the StructureScan 3D Transducer, is the transom

mounting bracket, and a hardware mounting kit. The transducer has

a 6 m (20 ft) cable attached.

Hardware mounting kit (included)

Transom mount screws #10x1-1/4" (3)

Bracket assembly bolts M6x12mm (2)

Bracket assembly washers M6 (4)

Bracket assembly nylon lock nuts M6 (2)

Transducer attachment screws M4x8mm (6)

Transducer attachment lock washers M4 (6)

Required tools and supplies (not included)

Drill Phillips (slotted-head screwdriver)

Drill bits Marine high-grade above- or below-

waterline sealant/adhesive compound

4Check the contents | StructureScan 3D Transducer

Installation

Mounting options

The transducer can be mounted on the transom, jackplate, step or

directly to your boat’s hull.

ÚNote: Step and direct to hull mount requires the separately

sold ‘Direct/Step mount (Flush bracket)’ mounting bracket.

Use the following table to determine which mounting option is

best suited to your boat/installation preferences.

ÚNote: When mounting the transducer, make sure there is

nothing around the mounting location that could interfere

with its sonar beams.

ÚNote: If mounting where the transducer comes out of the

water, for example when the boat is on plane, the sonar will

not work while the transducer is out of the water.

1Jackplate mount (Transom bracket)

2Direct Step mount (Flush bracket)

3Step mount (Transom bracket)

4Transom mount (Transom bracket)

Installation | StructureScan 3D Transducer 5

StructureScan 3D Transducer mounting options

"Transommount(Transom

bracket)" on page 9

•Keeps transducer in the water when the

boat is on plane, allowing you to track

bottom at high speeds

•Transducer angle can be adjusted so it is

parallel with the water

•Transducer more likely to collide with

obstructions in the water and adds drag

to the boat

"Jackplatemount(Transom

bracket)" on page 10

•Transducer is not in the water when boat

is on plane; protects transducer and

prevents drag from transducer

•Transducer angle can be adjusted so it is

parallel with the water

•Allows you to mount transducer without

drilling holes in your boat

•Sonar does not track bottom when

transducer comes out of the water

"Stepmount(Transom

bracket)" on page 12

•Transducer is not in the water when boat

is on plane; protects transducer and

prevents drag from transducer

•Transducer angle can be adjusted so it is

parallel with the water

•Sonar does not track bottom when

transducer comes out of the water

"DirectStepmount(Flush

bracket)" on page 13

•Transducer is not in the water when boat

is on plane; protects transducer and

prevents drag from transducer

•Transducer angle cannot be adjusted so

it is parallel with the water

•Sonar does not track bottom when

transducer comes out of the water

Transom mount bracket assembly

The transom mount bracket assembly comes with four washers, two

bolts and two nuts.

6Installation | StructureScan 3D Transducer

ÚNote: Ensure the cable has been threaded through the

bracket before running the cable through the boat.

ÚNote: The inside washer must be placed in the groove on

the curved shield before putting the bolt through from the

outside.

Flush mount bracket assembly

To mount the transducer directly to the step (Direct Step mount),

use the flush mount bracket (sold separately).

Installation | StructureScan 3D Transducer 7

Transducer angle

After mounting the transducer, make sure the transducer is adjusted

so it will be parallel with the waterline in both the horizontal and

vertical axis when moving at trolling speed.

üûû

Downscan Overlay

The StructureScan 3D transducer should be installed within

approximately 0.3 m (1 ft) of the broadband sounder transducer to

get optimum performance from the Downscan Overlay feature.

Downscan overlay feature performance could be degraded if the

StructureScan 3D transducer is too far away from the broadband

sounder transducer.

8Installation | StructureScan 3D Transducer

< 0.3m (1ft)

Transom mount (Transom bracket)

The transducer can be mounted on a transom bracket. With this

mounting option the transducer can be in the water when you are

on plane, or can be mounted so it is only in the water when you are

moving at trolling speed.

Transom mount (fiberglass) supplies (not included)

3 mm (1/8”) Drill bit (Transom

mount pilot holes)

Marine high-grade above- or

below-waterline sealant/

adhesive compound

Transom mount (aluminum hull) supplies (not included)

M4 Machine Screws Marine high-grade above- or

below-waterline sealant/

adhesive compound

Plastic isolating material such as King Starboard (prevents

corrosion between bracket and aluminum hull)

Installation | StructureScan 3D Transducer 9

To mount on transom using the transom bracket:

1. Choose a transducer location and then route the transducer

cables through the bracket and to the location where the

module will be installed.

2. Place the transducer bracket against the transom and then align

the bottom of the transducer with the bottom of boat. Use a

pencil to mark the pilot holes through the slots in the

transducer bracket.

3. Drill the pilot holes into the boat’s transom.

4. Apply a marine high-grade above- or below-waterline sealant/

adhesive compound to the pilot holes.

5. Align the bracket slots over the pilot holes and fasten the

bracket to the transom using the supplied screws.

6. To make adjustments to transducer position, loosen the screws

and slide bracket up or down.

7. Connect the transducer cables to the module sonar ports.

After the transducer is connected and your boat is in the water, turn

on the Flip Left/Right feature in your display unit to ensure what is

shown on the left and right side on your display corresponds with

what is on the left and right side of your boat. Refer to your display

unit's Operation manual for more information.

Jackplate mount (Transom bracket)

The transducer transom bracket can be mounted inside or outside

of the jackplate by drilling through the jackplate and then running

bolts through the hinge hole in the side of the bracket into the

jackplate. The illustration above shows the transom bracket

mounted inside the jackplate.

ÚNote: Sonar does not track bottom when the transducer is

out of the water.

10 Installation | StructureScan 3D Transducer

Altri manuali per StructureScan 3D

Indice

Altri manuali Lowrance Trasduttore

Lowrance

Lowrance P66 Manuale utente

Lowrance

Lowrance SIMRAD Ice transducer Manuale utente

Lowrance

Lowrance SpotlightScan Manuale utente

Lowrance

Lowrance SIMRAD Manuale utente

Lowrance

Lowrance EP-DDS SKIMMER Manuale utente

Lowrance

Lowrance StructureScan Manuale utente

Lowrance

Lowrance 000-15275-001 Manuale utente

Lowrance

Lowrance Transducer Manuale utente

Lowrance

Lowrance Active Imaging 3-IN-1 Manuale utente

Lowrance

Lowrance Skimmer Transducer Manuale utente

Lowrance

Lowrance Simrad LiveSight Ice Manuale utente

Lowrance

Lowrance Simrad LiveSight Manuale utente

Manuali Trasduttore popolari di altre marche

HBM

HBM AD101B Manuale utente

Camille Bauer

Camille Bauer SINEAX F534 Manuale utente

Trane

Trane KIT 16724 Istruzioni per il montaggio

Lumel

Lumel P18 Manuale utente

B&C Speakers

B&C Speakers DE75PTN Manuale utente

MAMAC SYSTEMS

MAMAC SYSTEMS PR-243 Manuale

Mianyang Weibo Electronic

Mianyang Weibo Electronic WB Series Manuale utente

ProMinent

ProMinent Dulcometer DMT Manuale utente

MKS

MKS MicroPirani 925 Series Come usare

WIKA

WIKA WU-20 Manuale utente

Alcatel Vacuum Technology

Alcatel Vacuum Technology BARATRON 622A Manuale utente

Camille Bauer

Camille Bauer SIRAX CH-5610 Manuale utente

WIKA

WIKA F2802 Manuale utente

Veris Industries

Veris Industries PW Series Manuale utente

HBM

HBM TJ1-S6 Manuale utente

Simrad

Simrad ES120-7C - REV D Guida utente

HBM

HBM C18 Manuale utente

Airmar

Airmar M260 Manuale di istruzioni