LP Morgan Galleria Manuale utente
www.lpmorgan.com.au
LP Morgan Galleria manual
Installation Instructions For:
• Plana U
• Novares
• Rear Projection
• Plana AT
2 | LP Morgan Installation Instructions
LP Morgan Galleria Manual
Table of contents
To the owner 3
Unpacking 4-5
Assembly instructions 6
Attaching the screen material 7-10
Trimming the screen material 10
Installing the assembled screen 11
Mounting the screen 12
Screen care 13-14
Warranty information 15
Information in this document is subject to change without notice.
© Herma Technologies. All rights reserved.
This document is protected against unauthorised copying electronic or otherwise.
Trademarks used in this text: Herma, the Herma Logo, Galleria, LP Morgan and
LP Morgan logo are registered trademarks of Herma Technologies.
Other trademarks and trade names used in this document remain the property
of the relevant owners.
June 2011 Version 3.2
LP Morgan Installation Instructions | 3
LP Morgan Galleria Manual
To the owner
Congratulations on purchasing an Australian made LP Morgan CineTheatre
Galleria Projection Screen. This cinema quality screen uses the finest optical
and mechanical components to give you a truly cinematic experience.
Please take a moment to review this manual, as it will ensure you many years
of service from your new LP Morgan CineTheatre Galleria Projection Screen.
Required tools and parts
6 or more screws to
suit wall type.
(Screw heads must be
no higher than 4mm)
Spirit level and pencil
for marking
Electric drill with drill
and driver bits
4 | LP Morgan Installation Instructions
LP Morgan Galleria Manual
Unpacking the Galleria Frame Screen
(Plana U / Novares / Rear Projection)
Supplied parts
Please check that you have all the components before assembly.
The EzyGrip and EzyMount are packed inside the fabric roll.
Front Projection Screens 140” and larger contain extra components.
See page 10.
1 x EzyMount
1 x Fabric Cutter
4 x Frame Sections
1 x Plastic Drop Sheet
4 x Corner Brackets
1 x 4mm Hex Key
1 x Fabric Roll
EzyGrip Lengths
LP Morgan Installation Instructions | 5
LP Morgan Galleria Manual
Unpacking the Galleria Frame Screen
(Plana AT)
Supplied parts
Please check that you have all the components before assembly.
The EzyGrip and EzyMount are packed inside the fabric roll.
Screens 140” and larger contain extra components.
See page 10.
1 x EzyMount
1 x Fabric Cutter
4 x Frame Sections
1 x Plastic Drop Sheet
Insertion Tool
4 x Corner Brackets
1 x 4mm Hex Key
Clamping Strip (numbered)
1 x Fabric Roll
EzyGrip Lengths
6 | LP Morgan Installation Instructions
LP Morgan Galleria Manual
Assembling the screen
Insert the corner brackets into
the short frame pieces first.
Be sure to insert them into the
lower channel and that the
grub screws are accessible
through the slot.
The corner brackets must be
inserted into the lower channel
Assemble the frame face down on a flat surface on the plastic drop sheet
provided. Please read the instructions carefully to avoid mistakes.
Attach the long frame pieces
into one end of the short
frame piece.
Insert the second short end
piece into the long frame pieces.
Check that all corners are firmly fitted together before tightening the grub
screws with the supplied hex key.
LP Morgan Installation Instructions | 7
LP Morgan Galleria Manual
The material is held in the
frame with EzyGrip. The
EzyGrip sits in its special
channel to hold the tension in
the screen.
Insert EzyGrip in the order shown below. Start at the corner of the frame
and work along the edge. Cut to length if necessary. Following the diagram
below insert the EzyGrip into the first side then when installing on the
opposite side apply tension to the fabric with one hand while inserting
the EzyGrip with the other.
1 2
34
5
6 7
8
• Insert the EzyGrip in the order shown
• Avoid lifting up the fabric, as the
EzyGrip may pop out
Roll the screen material onto the back of the screen. There is a sticker
attached to show you which side is the viewing side.
Attaching the screen material
(Plana U / Novares / Rear Projection)
EzyGrip in the wrong channel
EzyGrip in the wrong way around
Correct insertion of EzyGrip
8 | LP Morgan Installation Instructions
LP Morgan Galleria Manual
The material is held in the
frame with EzyGrip. The
EzyGrip sits in its special
channel to hold the tension in
the screen.
Allow enough fabric to overlap the frame sides to ensure the fabric can be
tensioned by hand.
Roll the screen material onto the back of the screen. There is a sticker
attached to show you which side is the viewing side.
Attaching the screen material (Plana AT)
EzyGrip in the wrong channel
EzyGrip in the wrong way around
Correct insertion of EzyGrip
LP Morgan Installation Instructions | 9
LP Morgan Galleria Manual
Insert the first section of EzyGrip into the correct channel using your
fingers, or hand tool provided.
Cut EzyGrip to length if necessary. Screw a matching numbered piece
of Clamping Strip to secure each length of EzyGrip in place as you
progress.This will stop the EzyGrip pulling out as tension is applied to
the fabric surface.
Start at the first corner of the joined frame and work around the edge.
Following the diagram below, insert the EzyGrip along the first side.
You can insert the lengths of EzyGrip in either a clockwise or
anticlockwise direction.
Clamping Strips
Start here Work in clockwise or
anticlockwise direction
Stretch and apply
tension to fabric
at each corner to
reduce ripples
Stretch and apply
tension to fabric
at each corner to
reduce ripples
Stretch and apply
tension to fabric
at each corner to
reduce ripples
Apply tension to the
fabric with one hand
while inserting the
EzyGrip with the other.
Tek Screw
Clamping Strip
Handle of EzyGrip
Frame Screen
1 2 3
4
5
678
9
10
10 | LP Morgan Installation Instructions
LP Morgan Galleria Manual
If you have ripples or creases in the image area, don’t panic! You can easily
remove the EzyGrip, retension the surface and re-install the EzyGrip.
1. Remove the clamping strip.
2. To remove the EzyGrip push
the handle forward, then lift it
up to remove.
3. Fix the clamping strip.
For Plana AT:
Be sure you have the tension correct before trimming the screen material,
as it is best not to remove the EzyGrip after trimming. Trim the excess fabric
with the fabric cutter supplied.
Trimming the screen material
Excess Fabric
Cutter
Slide the cutter
along the frame
while holding the
material. Avoid
lifitng the fabric.
• Hold the fabric with one hand, while
sliding the cutter along the inside
edge of the frame.
• Avoid lifting up the fabric, as the
EzyGrip may pop out.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali LP Morgan Schermo di proiezione
LP Morgan
LP Morgan Rondo Opus Manuale utente
LP Morgan
LP Morgan HideAway LPM30HID220 Manuale utente
LP Morgan
LP Morgan Screenboard Manuale utente
LP Morgan
LP Morgan Rondo Manuale utente
LP Morgan
LP Morgan Galleria Curve Manuale utente
LP Morgan
LP Morgan LPM DUO Manuale utente
LP Morgan
LP Morgan Galleria Eclipse Manuale utente
LP Morgan
LP Morgan CineTheatre Galleria Curve Manuale utente
