Ltech LT-905 Manuale dell'operatore
Technical Specs:
LT-905
DMX512/RDM
3-pin XLR, RJ45
~
×
× 5CH
Max. 600W
12 24Vdc
5A 5CH Max. 25A
(0~60W...120W)
8bit (256 levels) / 16bit (65536 levels)
2
Protection:
Working Temp.:
:
:
:
Dimensions
Package Size
Weight (G.W.)
1
Product Introduction:
www.ltech-led.com www.ltech-led.com
Model
Input Signal
Input Voltage
Current Load
:
:
DMX Interface:
:
:
:
Output Power:
Grey Level
Product Size:
The Unit: mm
6. With fast self-testing function.
8. 16bit (65536 levels) / 8bit (256 levels) grey level optional.
7. High/low frequency PWM for optional
5. With shortcut protection and over load protection, as well as warning function when
fault.
4. With RDM remote management protocol, the operations can be completed via the
RDM master console, such as parameters browsing & setting, DMX address setting,
equipment recognition, etc.
2. Easy operation with digital display and the touch buttons.
1. Designed with 5 channels output, and Max. 5A current per channel, up to 600W output
power.
3. Support 2 kinds of DMX ports: 3-pin XLR, RJ45.
www.ltech-led.com
LT-905
Shortcut / Over load protection
8 bit / 16 bit
2 kinds of DMX interfaces
CHANNELS
Shortcut / Over load
-30℃~65℃
L122×W110×H37mm
L127×W123×H41mm
550g
Wiring Diagram:
1 Connecting LED lights:
2. DMX console onnectionc :
An amplifier is needed if more than 32 decoders are connected ,
signal amplification should not be more than 5 times continuously.
or use overlong signal wire
If the recoil effect occurs because of longer signal line or bad line quality, please try to
connect 0.25W 90-120Ω terminal resistor at the end of each line.
LT-905 is equipped with 2 types DMX
terminals for users’ selection. The following
diagram takes 3-pin XLR as an example,
same connecting method for RJ45.
*
*
These 2 terminals can be connected in a mixed way.
RJ45 Connected in Parallel
Update Time: 2017.04.18_A0
3-pin XLR Connected in Parallel
3. The connection diagram of 2 kinds of DMX/RDM terminals:
www.ltech-led.comwww.ltech-led.com www.ltech-led.com www.ltech-led.com
43 65
*
Installation Attention : please reserve enough ventilation distance between decoders (>20mm),
be sure not to block the vent, or will affect lifetime of decoder for .poor heat dissipation
Main Component Descripition:
RJ45
3-pin XLR
DMX/RDM
input & output
DMX/RDM
input & output
Power
indicator
Signal
indicator
12-24Vdc
Power input
Green terminals
LED lamps connection
Digital display
Digital
display
Screen
Hig Smooth
Low Std
30S off
Enable
PWM Hz DIM
Digital display will enter the locked
mode without operating after 15S.
Dip
switch
Dip switch
16
Bit
8
M
<
<
Long press “M” key to unlock.
Short press “M” key to switch numbers.
Press “ ””v” key to adjust value.
^
Altri manuali per LT-905
1
Altri manuali Ltech Convertitore multimediale
Ltech
Ltech LT-8030 Manuale utente
Ltech
Ltech LT-830-8A Manuale utente
Ltech
Ltech LT-995 Manuale utente
Ltech
Ltech LT-830-350 Manuale utente
Ltech
Ltech LT-912 Manuale utente
Ltech
Ltech WP-804 Manuale utente
Ltech
Ltech LT-916 Manuale di riferimento
Ltech
Ltech LT-830-700 Manuale utente
Ltech
Ltech LT-904 Manuale utente
Ltech
Ltech LT-905 Manuale utente
Ltech
Ltech LT-904 Manuale utente
Ltech
Ltech LT-995 Manuale utente
Ltech
Ltech LT-830 Manuale utente
Ltech
Ltech LT-DMX-6803 Manuale utente
Ltech
Ltech LT-995 Manuale utente
Ltech
Ltech M4-E Manuale utente
Ltech
Ltech LT-DMX-1809 Manuale utente
Ltech
Ltech LT-851-5A Manuale utente
Ltech
Ltech LT-916 Manuale utente
Ltech
Ltech LT-916 Manuale utente
