Lumel P20 Manuale utente
1
USER’S MANUAL
TRANSDUCER OF TEMPERATURE
AND STANDARD SIGNALS
P20
2
3
Contents
1. APPLICATION ..........................................................................................5
2. TRANSDUCER SET ..................................................................................5
3. OPERATIONAL SAFETY ...........................................................................6
4. INSTALLATION ........................................................................................7
4.1. Fitting way .............................................................................7
4.2. External electrical connection diagrams ..............................8
5. SERVICE ..................................................................................................9
5.1. Transducer configuration by means of the eCon software .......... 10
5.1.1 Configuration of the transducer input type .......................11
5.1.2 Configuration of the individual analog output characteristic......12
5.1.3 Configuration of the analog output at overflows ...............13
5.1.4 Readout of the measured value .................................................14
5.1.5 Readout of the serial number and software version ...........15
6. TECHNICAL DATA ..................................................................................16
7. EXECUTION CODES ...............................................................................18
8. MAINTENANCE AND GUARANTEE .........................................................20
4
5
1. APPLICATION
The P20 programmable transducer is designed to convert temperature,
resistance, voltage from a shunt and standard signals into a constant-
current or constant-voltage standard signal.
The output signal is galvanicaly isolated from the input signal and
supply.
The transducer compensates automatically the resistance of wires in
case of resistance value measurements in a three-wire system and au-
tomatically compensates the temperature of terminals in case of mea-
surements from thermocouples.
The transducer is fully configurable through the PD14 programmer. By
means of this programmer, one can change the input type, the measu-
rement averaging time and rescale the analog output acc. to the indivi-
dual output characteristic, and also read out the measured value.
2. TRANSDUCER SET
The set of the P20 transducer is composed of:
- P20 transducer 1 pc.
- User’s manual 1 pc.
- Plug with screw terminals 2 pcs.
- Hole plug of the programmer socket 1 pc
When unpacking the transducer, please check whether the type and
execution code on the data plate correspond to the order.
6
3. OPERATIONAL SAFETY
In the safety service scope, the transducer meets to requirements of the
EN 61010-1 standard.
Observations concerning the operational safety
lAll operations concerning transport, installation, and commissioning
as well as maintenance, must be carried out by qualified, skilled
personnel, and national regulations for the prevention of accidents
must be observed.
lBefore switching transducer on, one must check the correctness
of connections to the network.
lWhen connecting the supply, one must remember that a switch or
a circuit-breaker should be installed in the building. This switch
should be located near the device, easy accessible by the
operator, and suitably marked as an element switching the
transducer off.
lDo not connect the transducer to the network through
an autotransformer.
lBefore removing the transducer housing, one must switch the
supply off and disconnect measuring circuits.
lThe removal of the transducer housing during the guarantee
contract period may cause its cancellation.
lThe programmer socket is only use to connect the PD14
programmer. After the transducer programming, one must
insert the hole plug.
lNon-authorized removal of the housing, inappropriate use, incorrect
installation or operation, creates the risk of injury to personnel
or a transducer damage.
For more detailed information, please study the User’s Manual.
7
22.5
41
4. INSTALLATION
4.1. Fitting way
P20 transducers are designed to be mounted on a 35 mm rail accor-
ding to EN 60715.
Housing dimensions are: 22.5 x 120 x 100 mm.
On the transducer outside, there are screw or self-locking terminal strips,
which make possible the connection of external wires with a 2.5 mm2
cross-section (supply and output) and up to 1.5 mm2(input).
Connector of the PD14 programmer
Fig. 1. Overall dimensions and fitting way of the transducer
Transdusers should be mounted on the rail in direct contact with an-
other devices that emit heat (eg transducer P20). You must keep a mini-
mum 5 mm distance between the devices to allow emit heat from the
housings to the ambient. Otherwise, the in rated operating temperature
of transducer which is in direct contact with the other transducer may
exceed the rated operating temperature stated operating conditions.
8
RTD in a three-wire
system
RTD in a two-wire
system or resistance
measurement
TC or voltage
- 60... 60 mV
0... 60 mV
- 150... 150 mV
0... 150 mV
Current
- 20... 20 mA
0... 20 mA
4... 20 mA
Voltage
- 10... 10 V
0... 10 V
0... 5 V
4.2. External electrical connection diagrams
The transducer has two sockets of terminal strips, which two plugs with
terminal screws are connected to. The way to connect external signals
is shown on the fig.1
The electrical connection diagram is also situated on the transducer
housing. In case of the transducer work in an environment with high
interferences, one must apply shielded wires in the transducer input.
Fig.2. Electrical connection diagrams of the P20 transducer.
9
5. SERVICE
After switching the transducer on, the work state diode should light in
red for a moment, next it should light in green.
P20
supply analog
output
Fig. 3. View of the P20 transducer
Diode of the transducer work state:
- the state diode lights in green – normal
work,
- the state diode lights in red – improper work
parameters; one must configure the trans-
ducer again,
- the state diode pulsates in red – lack of
calibration or the non-volatile memory is
damaged; one must return the transducer to
the manufacturer.
Confirmation of the separator’s communication with PD14 programmer
is indicated by the status diode which turns off for short period of time.
10
Fig. 4. Configuration of the connection with the P20 transducer.
5.1. Transducer configuration by means
of the eCon software
The eCon software is destined for the P20 transducer configuration.
One must connect the PC computer through the PD14 programmer and
configure the connection choosing Communication -> Serial port from
the menu (for the P20 transducer, we choose the address 1, baud rate
9600 kb/s, the mode RTU 8N2 and the appropriate port COM under
which the controller of the PD14 programmer has been installed).
After configuring the connection, use the Connect button.
The eCon software will automatically identify the device and con-
nect to it and display all parameters in the panel P20- Configuration.
To change parameters, enter the new value in the parameter window
and click the Save button.
Altri manuali per P20
1
Indice
Altri manuali Lumel Trasduttore
Lumel
Lumel P30U series Manuale utente
Lumel
Lumel P30P Manuale utente
Lumel
Lumel P300 Manuale utente
Lumel
Lumel P20G series Manuale utente
Lumel
Lumel P18-0 Manuale utente
Lumel
Lumel P43 Manuale utente
Lumel
Lumel P18L Manuale utente
Lumel
Lumel P30H Manuale utente
Lumel
Lumel P30U series Manuale utente
Lumel
Lumel ULT20 Manuale utente
Lumel
Lumel P19 Manuale utente
Lumel
Lumel P41 Manuale utente
Lumel
Lumel P30O Manuale utente
Lumel
Lumel P18 Manuale utente
Lumel
Lumel P30H Manuale utente
Lumel
Lumel P21Z Series Manuale utente
Lumel
Lumel VTR10 Manuale utente
Lumel
Lumel P20Z Manuale utente
Lumel
Lumel P18D Manuale utente
Lumel
Lumel P11P Manuale utente
