Lumena Pathos 316 Manuale utente

Full product range & more information: www.lumenalights.com

INSTRUCTIONS

Pathos 316 Marine Grade Stainless Steel Path Light

With Photocell

600mm & 800mm

WARNINGS

PLEASE READ THESE INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION / MAINTENANCE

•If a fitting is found to be damaged, cease use immediately.

•This is a Class 1 product and must be earthed.

•This unit must be fitted by a competent and qualified electrician.

•Install in accordance with IEE wiring regulations and current Building Regulations.

•To prevent electrocution, switch off mains supply before installing or maintaining this fitting. Ensure

other persons cannot restore the electrical supply without your knowledge.

•This light fitting should be connected to a circuit with a 30Ma RCD fitted. Maximum 12-15 fittings on

each circuit recommended.

•If replacing an existing fitting, make a careful note of the connections.

•All connections should be made as watertight as possible to avoid electrical shortage.

•When changing the bulb, always switch off at the mains & allow to cool before handling.

•Always use the correct type & wattage bulb. Never exceed the wattage stated.

•The unit may get warm whilst on for a period of time.

CLEANING / CARE OF STAINLESS STEEL:

Occasional cleaning and care is recommended for this product. Contrary to popular belief, Stainless Steel needs looking after,

especially in exposed and coastal areas. If not cleaned on a regular basis, the acid that is ever present in the air and salt in coastal

areas, will affect the surface causing pitting and even rust like staining to appear. To keep your lights looking good, simply wipe

clean the outside with a damp cloth and then dry once a month, (more frequently in coastal areas). Specialist stainless steel

cleaning products can be used but never use an abrasive cleaner. In extreme conditions it may be advisable to apply a clear

lacquer or varnish to protect the surface. Lumena recommend and stock Kilrock stainless steel cleaner.

For further information please refer to our website.

WARNING - Ensure all surfaces are completely dry prior to switching on the fitting after cleaning.

RETURNS:

If purchased from a 3rd party, please contact your supplier. If purchased direct, contact us by phone or email:

Lumena Lights Ltd, Centre 33 Long March, Daventry, NN11 4NR Tel: +44 1327 871161 Email: sales@lumenalights.com

Our full returns policy is available on our website.

Waste Electrical Products should not be disposed of with household waste. Please check with your local authority or contact us

for more information. Please recycle packaging whenever possible.

Producer Registration Number: WEE/KC3440XY

Voltage: 220 - 240v

Max. Wattage: 20w

Bulb Holder: ES / E27

Recommended Bulb: 15w LED Corn Bulb or Candle Bulb

IP Rating: IP44

Cable: 1.5mm 3 Core (H07RN-F)

Cable Length: 0.5m (approx.)

Product Heights: 0.6m / 0.8m

Sensor: Photocell (Dusk to Dawn)

Materials: 316 Marine Grade Stainless Steel and Polycarbonate

Mount: Internal Mounting Base (adjustable)

Dimensions: Diameter = 100mm, Overall Height = 600mm or 800mm

INCLUDED: Bollard, 2 x Allen Keys, 3 x Mounting Screws & Plugs, 1 x Junction Box, Instructions

✔✔✔

3 YEAR

GUARANTEE

see website for

more details

Reduced warranty for

specific components

RoHS

Full product range & more information: www.lumenalights.com

INSTALLATION:

IMPORTANT: Cable should be laid inside armoured conduit or piping to protect from water-logging, chemicals

found in soil and damage. If buried, it should be buried to at least 0.5m below ground to reduce damage risk. If

this method is not used, cable warranty will be void.

This bollard should be securely fixed to a concrete base, brick, paving slab or quality wooden decking. It should not be installed

directly into soil.

1. Remove internal mounting base from the bollard body by removing the 3 x

socket screws.

2. Drill out the 3 mounting holes using a 6mm masonry drill bit and insert the

plastic wall plugs (supplied).

3. Locate and remove the connection block from inside the tube and insert the

cable into the waterproof junction box, as well as the mains cable.

4. Strip back the 3 inner wires of the mains power cable to reveal the Live

(brown), Earth (yellow & green) and Neutral (blue).

5. Insert the wires into the correct terminals of the terminal block, ensuring

the brown mains Live wire is connected to Live in of the Photocell (L),

the three blue Neutral wires (N) are connected to one another and the

two yellow and green Earth wires are connected to one another –See

diagram.

6. Fully tighten the terminal block screws to clamp the wires down,

ensuring they make a connection to the conductor, not the rubber

sheath.

7. Once the wiring is complete, ensure the junction box is sealed / fully

water right, and return back inside the post.

8. Insert the stainless steel bolts through the mounting plate and secure in

place (adjust base as required –see below).

9. Replace the tube over the base and fasten the 3 x socket screws

to secure.

ADJUSTABLE MOUNTING BASE:

The Pathos 316 incorporates a unique adjustable mounting base plate which enables

installation on uneven surfaces.

1. Loosen the socket screws on the mounting base with the allen key provided.

2. Loosely secure the base to the surface as per above.

3. Using a spirit level, adjust the socket screws accordingly to level off the base.

4. Fully tighten the mounting screws to complete installation.

LAMP INSTALLATION / REPLACEMENT: (Ensure power is turned off prior to changing the lamp)

1. Unscrew the head to reveal bulb holder.

2. Remove / Insert lamp (screw base –E27).

3. Replace head and turn until head becomes secure on the fitting.

IMPORTANT: Condensation can occur due to the warmth inside the fitting produced by the lamp and the cold air outside. If

this is noticed, on a dry day, turn off the power supply, safely remove the head, and wipe dry with a soft cloth. It is

recommended to change lamps / install on a warm, dry day.

CABLES:

Neutral (N) = Blue

Live (L) = Brown

Earth = Yellow & Green

Colours of wire sleeving may vary

slightly –Test prior to use.

Indice

Altri manuali Lumena Luce esterna

Lumena

Lumena VERSA Decimina Manuale utente

Lumena

Lumena AlvaLED LED TWIN Spike Light Manuale utente

Lumena

Lumena ProSolar Olympia Manuale utente

Lumena

Lumena Charleston Eyelite Manuale utente

Lumena

Lumena VIAMAX Hiway MAX 40W PIR Solar Street Light Manuale utente

Lumena

Lumena Pro solar OLYMPIA Manuale utente

Lumena

Lumena OLYMPIA Manuale utente

Lumena

Lumena OLY800-W/GSK-PS2 Manuale utente

Lumena

Lumena Ultra-Spike Light Manuale utente

Lumena

Lumena ProSolar Halomarka Manuale utente

Lumena

Lumena UNILED08-R Manuale utente

Lumena

Lumena Boleda CONUS Manuale utente

Lumena

Lumena Viamax Olympia MAX Manuale utente

Lumena

Lumena OLY800-D-PIR/GSK-PS2 Manuale utente

Lumena

Lumena Prosolar Alerta Manuale utente

Lumena

Lumena Charleston Brick Light Manuale utente

Lumena

Lumena PROSOLAR Sol-Icon Manuale utente

Lumena

Lumena Boleda VENTUS Manuale utente

Manuali Luce esterna popolari di altre marche

Sealey

Sealey LED37 Manuale utente

nordlux

nordlux VEJERS Guida utente

SImx

SImx ELITE LED LHTC637 Manuale utente

GEV

GEV CAROLINE 10833 Manuale utente

NEBO

NEBO NEB-LSP-0020 Manuale utente

WE-EF

WE-EF PFL540 LED Manuale utente

Lindby

Lindby 9949029 Manuale utente

HEPER

HEPER DOGO Side LW6048.585-US Istruzioni per l'installazione e il funzionamento

HEPER

HEPER LW8034.003-US Istruzioni per l'installazione e il funzionamento

Maretti

Maretti VIBE S 14.6080.04.A Manuale utente

BEGA

BEGA 84 253 Manuale

HEPER

HEPER MINIMO Istruzioni per l'installazione e il funzionamento

LIGMAN

LIGMAN BAMBOO 3 Manuale utente

Maretti

Maretti TUBE CUBE WALL 14.4998.04 Manuale utente

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB Manuale utente

urban ambiance

urban ambiance UQL1273 Manuale utente

TotalPond

TotalPond 52238 Manuale utente

Donner & Blitzen

Donner & Blitzen 0-02661479-2 Manuale utente