LUX KONOz Manuale utente

Installaon Manual

Smart Hub

THERMOSTAT

™

Thank you for inving KONOz™into your home. The setup process

is easy. All you need to do is follow these simple steps and you’ll

be on your way to saving energy and making your home even more

comfortable.

LUX Products oers installaon and product videos

Please visit LuxProducts.com/videos or visit our YouTube channel

LUX Products Corporaon.

Note: To contact LUX Technical Support, please call 856.234.8803.

Para ver estas instrucciones en español, por favor visite.

LuxProducts.com/KONOzmanualSP

LuxProducts.com | 3

1. START HERE

Tools Needed

Table of Contents

1. Start Here ......................................................................................2-5

2. Installing KONOz ..........................................................................6-10

3. Operang KONOz ......................................................................11-16

4. Appendix....................................................................................17-19

KONOz

Drill Oponal: Wire Stripper Smart HubPhillips Screwdriver

Baeries

What’s in the box?

Screws Wall Anchors

Trim Plate Wiring Labels

4 | 856.234.8803

This manual is a comprehensive guide for the installaon and wiring

of your KONOz thermostat.

Step 1.1: Turn o the power at the circuit breaker to both

your heang and cooling systems before performing any

wiring.

Step 1.2: Conrm that your heang

and cooling system is powered down by changing the

temperature on your exisng thermostat. The heang

and cooling should not come on but may show the

temperature change on your exisng thermostat.

Note: Your system should not make any noise and you

should not feel any air exing your vents.

Step 1.3: Remove the front of your old thermostat

from its base.

If you see thick black wires, wire nuts, or any

labels that say 120-240VAC or High Voltage, your

system is not compable with KONOz . Please call

LUX Technical Support at 856.234.8803 before proceeding with your

installaon. If you do not see any high voltage labels or wires, you may

connue with the installaon process.

HIGH

VOLTAGE

STOP

LuxProducts.com | 5

Step 1.4: Take a picture of your current wiring layout. The picture can

be used as reference later.

Step 1.5: Use the included wire labels to mark which wire is connected

to each terminal in your old thermostat.

Note: Wiring leer designaons correspond to either a “Heat Pump” or

“Convenonal” system.

Note: A wiring compatability tool is available at

LuxProducts.com/wiring

1. START HERE

6 | 856.234.8803

Wiring

Step 2.1: Idenfy your system conguraon (see wiring diagrams in

appendix). Potenal conguraons include:

System Conguraon Wiring Conguraon

Convenonal: 1H/1C without C-wire Y, G, W1, R

Convenonal: 1H/1C with C-wire Y, G, W1, R, C

Convenonal: 2H/1C without C-wire Y, G, W1, W2, R

Convenonal: 2H/1C with C-wire Y, G, W1, W2, R, C

System Conguraon Wiring Conguraon

Heat Pump: 1H/1C with C-wire Y, G, R, O/B, C

Heat Pump with auxiliary or dual fuel: Y, G, R, O/B, W1, C

If you have only one R wire, please use the RH terminal. If you have a

dierent conguraon other than what is listed above, please call LUX

Technical Support for help with your installaon. If you have a “C” wire

then the included baeries are not needed.

Note: If you do not have a C-wire but would rather not use replaceable

baeries, please visit shop.LuxProducts.com/PowerBridge to learn more

about our Lux Power Bridge soluon.

LuxProducts.com | 7

Step 2.2: Verify that each wire has been properly labeled and remove

each wire from its terminal — make sure that they don’t fall into the

wall.

Step 2.3: Remove the mounng screws from the base of the old

thermostat and remove the base from the wall.

Step 2.4: Separate KONOz from its base.

Step 2.5: If you would like to use the trim

plate or wall anchors, you may install them

now.

Step 2.6: Pull the wires from your wall

through the center hole of the KONOz

base. Secure the base to the wall using the

included mounng hardware. Follow the

built in level to ensure that it is straight.

INSTALLATION

2. WIRING

Step 2.4

Step 2.5 Step 2.6

8 | 856.234.8803

Opon 1 - Convenonal (furnace) Systems:

Step 2.7f: Follow the terminal labels

marked “Convenonal” on the thermostat

base. Press the lever and insert each

labeled wire into the top hole of the

corresponding terminal.

Step 2.8f: If you have both an RC and RH wire present, then remove the

red cap next to the reset buon. You can now proceed to step 2.9.

Opon 2 - Heat Pump Systems:

Step 2.7hp: Follow the terminal labels

marked “Heat Pump” on the thermostat base.

Referencing your wiring photo, press the

lever and insert each labeled wire into the top

hole of the corresponding terminal.

If your old thermostat did not have a W1 wire but did have a W2 wire,

insert the W2 wire into the W1 terminal.

Step 2.8hp: If you have both an O wire and a B wire

(i.e. in a Trane system), install the B wire in the “C” terminal.

For more detailed direcons, please see the wiring diagrams in the

appendix or call LUX Technical Support.

CONVENTIONAL C Y1 W2

HEAT PUMP C Y1 O/B

POWER BRIDGE 4

CONVENTIONAL C Y1 W2

HEAT PUMP C Y1 O/B

POWER BRIDGE 4

LuxProducts.com | 9

Wiring

Step 2.9: If you do not have a C-wire, insert the (4)

AA baeries included with your KONOz thermostat

according to their correct polarizaon markings

found on the KONOz.

Securely fasten KONOz onto its base. Once it has

clicked into place, return power to your heang

and cooling system.

Note: If baeries are installed, you must replace all baeries with only

premium brand alkaline baeries at least once every two years.

To replace the baeries, remove the KONOz from it’s base (ie

disconnecng it from its supply mains) and insert (4) AA premium

brand alkaline baeries. If you discover leaky or damaged baeries, do

not touch the baeries. Leaky or damaged baeries must be handled

with proper safety equipment included safety glasses with side shields,

and neoprene or natural rubber gloves in a well-venlated room.

For disposal of baeries, abide by the local laws and regulaons of your

region. If you are not able to idenfy the applicable rules in your area,

please check the instrucons of the baery manufacturer.

For disposal of KONOz, you must remove baeries prior to disposal.

INSTALLATION

2. WIRING

10 | 856.234.8803

Step 2.11: Aer conrming your system sengs, KONOz

will ask if you would like to connect to a Smart Hub. Select “SET”

to establish a connecon with your Smart Hub or select “OFF” to

connect later. For details on how to congure KONOz for your parcular

Smart Hub please visit: LuxProducts.com/KONOzSmartHubSetup

(F) for Furnace or Boiler:

Set the fan type to Gas (most

common), Electric (for systems

without gas or oil), or Boiler (no

fan).

(HP) for Heat Pump:

Set the valve type to O or B - look

at the photo of your wiring to see

your valve type.

First you will need to set your system type:

Step 2.10: Your KONOz is now ready to be congured for your heang

and cooling system. The KONOz will guide you through the inial system

conguraon. Use the knob to change opons and press the knob to

conrm your selecon.

Altri manuali per KONOz

Indice

Manuali Termostato popolari di altre marche

EWELLY

EWELLY EW-181 Manuale utente

Prolon

Prolon T1100 Istruzioni per l'installazione

Computherm

Computherm Q20 Manuale utente

Heatmiser

Heatmiser neoStat Manuale utente

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuale utente

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuale utente

Saswell

Saswell SAS920XWHB-7-S-RF Guida

Aircalo

Aircalo TFP1-ET85P2 Manuale utente

Honeywell

Honeywell CM721 Manuale utente

Carrier

Carrier DEBONAIR 33CS Manuale utente

Lennox

Lennox iHarmony Zone Thermostat Istruzioni per il montaggio

Gemtech

Gemtech GT7000 Manuale di istruzioni

Rollei

Rollei Smartes 45000 Manuale utente

Sinope

Sinope TH1300RF Manuale utente

Honeywell

Honeywell RLV4305 Manuale utente

Honeywell

Honeywell Prestige 2.0 THX9421 Manuale utente

NuTone

NuTone NTBZ48 Istruzioni operative originali

Stelpro

Stelpro MAESTRO ASMT402AD Manuale utente