LuxaFlex Duette UltraGlide Guida

LUXAFLEX®DUETTE® SHADES

UltraGlide®Lifting System

Installation •Operation

CONTENTS

Getting Started:

Product View ................................................................ 1

How to Operate the Shade............................................. 2

Tools and Fasteners Needed .......................................... 3

Installation:

Installation Overview .................................................... 4

Mount the Installation Brackets — Reveal Mount............ 5

Mount the Installation Brackets — Face Mount............... 6

Mount the Installation Brackets — EndMount ................ 8

Install the Shade ........................................................... 9

Level the Rail(s), If Necessary....................................... 10

Install the Wand .......................................................... 11

Operation:

Operate the Shade ...................................................... 12

Troubleshooting .......................................................... 13

Care:

Removing the Shade, If Necessary ............................... 14

Cleaning Procedures ................................................... 14

® Registered Trade Marks of Hunter Douglas Limited •18.017.159 •04/2019

GETTING STARTED

Product View

Installation

Brackets

Wand

Top-Down/Bottom-Up

UltraGlide®

Standard

Day/Night

OPERATION

How to Operate the Shade

For smooth operation, keep the wand close to the fabric when raising and lowering the shade.

To Lower the Shade

■Pull the wand toward the center of the shade at about a

45° angle. The locking mechanism at the top of the wand

releases with a “click.” The shade lowers as you allow the

wand to return to the vertical position.

IMPORTANT: The wand must be pulled in close to the front

of the shade. Do not pull the wand out away from the shade.

■To stop the shade while lowering, move the wand back

toward the vertical position 15° out and give a slight

downward pull to engage the locking mechanism.

■If the shade hits an obstruction as it is lowered it will stop, which may cause the cords in

each cord rout to become misaligned. This may cause the shade to be angled or tilted when

fully raised. If this occurs, do the following:

➤Raise the shade slightly.

➤Lower the shade completely to the sill. In some cases, pull gently on the bottom rail to

get it to drop completely.

IMPORTANT: If the shade is tilted when fully raised, do not pull harder on the wand. It does

not correct the tilt and may make it worse.

To Raise the Shade

■Pull the wand straight down or slightly toward the outside.

➤With each stroke the shade partially raises.

➤Allow the wand to retract after each downward stroke.

➤Use multiple strokes until the shade reaches the

desiredposition.

Day/Night and Top-Down/Bottom-Up Shades

■To operate Day/Night and Top-Down/

Bottom-Up shades, the right wand

operates the middle rail and the left

wand operates the bottomrail (unless

reverse controls were speciﬁed on the

order).

IMPORTANT: You must ﬁrst lower the

bottom rail before lowering the middle

rail. Likewise, you must ﬁrst raise the

middle rail before raising the bottom rail.

To Raise: Pull the wand straight

down with short strokes.

To Lower: Pull the wand toward

the center of the shade

and release.

To Raise: Pull the wand straight

down with short strokes.

To Lower: Pull the wand toward

the center of the shade

and release.

This wand

operates the

bottom rail.

This wand

operates the

middle rail.

Middle

Rail

Bottom Rail

GETTING STARTED

Thank you for purchasing Luxaﬂex®Duette®UltraGlide®Shades. With proper installation,

operation, and care, your new shades will provide years of beauty andperformance.

Please thoroughly review this instruction booklet and the enclosed packing list before beginning

the installation.

Tools and Fasteners Needed

■Flat blade and Phillips screwdrivers

■Level (laser level is recommended)

■Measuring tape and pencil

■Power drill, 3mm drill bit, and 6mm hex driver

■Open end wrench (8mm)

■OPTIONAL: pliers

In addition, you will need fasteners designed to work with your speciﬁc mounting surface(s).

■#6 Hex Head Screws (Provided). Two 38mm screws are provided per installation bracket.

■Longer #6 Hex Head Screws (Not Provided). If using spacer blocks, use #6 screws long

enough for a secure attachment.

■#6 Flat Head Screws (Provided). If end mounting the shade, use two 38mm screws per

installation bracket.

■Speed Nuts and Screws (Provided). Extension brackets come with speed nuts and screws.

■Drywall Anchors (Not Provided). Use drywall anchors when mounting into drywall.

Speed Nut

and Screw

(Provided with Each

Extension Bracket)

#6 x 38mm

Hex Head Screw

(Provided)

Longer #6 Hex Head Screw

for Use with Spacer Blocks

(Not Provided)

#6 Flat Head Screw

for Use with End Mounts

(Provided)

INSTALLATION

Installation Overview

■Your order will include the correct number of installation

brackets for your shade width, as shown in the table.

➤For end mounts, only two brackets are used up to the

maximum width of 1820mm.

Mounting Types and Window Terminology

If the installation brackets are mounted correctly, the rest of the installation process follows

easily. To prepare for this important ﬁrst step, review the mounting types and basic window

terminology illustrated below.

■Refer to the appropriate page below based on your order:

➤Reveal Mount — Page5

➤Face Mount — Page6

➤End Mount — Page8

Installation

Bracket

End Mount

Brackets

Face Mount

Shade mounts outside

window opening.

Reveal Mount

Shade ﬁts within

window opening.

Collectively, the sill and

jambs are called the

“window casement.”

Molding

Head Jamb

Sill

Jamb Jamb

Shade

Width

Brackets

Required

300mm – 914mm 2

915mm – 1828mm 3

1829mm – 2743mm 4

2744mm – 3659mm 5

3660mm – 4420mm 6

INSTALLATION

Mount the Installation Brackets — Inside Mount

■Measure 50mm from each jamb for bracket location.

➤If more than two installation brackets came with your order, space additional bracket(s) evenly

between the two end brackets and mark their location. Mount into wood whenever possible.

■Centre the brackets on yourmarks, then mark the screw holes.

➤The minimum casement depth for mounting the installation brackets is 6mm. Mark both of the

winged screwholes with shallow mounting depths.

➤The minimum casement depth for a fully recessed mount 20mmcell sizes. Mark the center

screw hole when depth permits.

IMPORTANT: The front edges of the brackets must be level and aligned to each other.

■Drill the screw holes using a 3mm drill bit.

CAUTION: Use drywall anchors when mounting into drywall.

■Use a level to check that the mounting surface is level. Shim the brackets if necessary.

■Attach the installation brackets using the screws provided.

Proceed to “Install the Shade” on page 9.

50mm Space Evenly

Jamb Jamb

Space Evenly 50mm

Minimum

6mm Use Center Hole

When Depth Permits

INSTALLATION

Mount the Installation Brackets — Face Mount

■Center the headrail over the window opening at the desired height. Use a pencil to lightly

mark each end of the headrail on the mounting surface.

➤Alternatively, measure the width of the headrail and use that width to mark the headrail

end points over the window opening.

■Mark 50mm from each end of the headrail.

➤If more than two installation brackets came with your order, space additional bracket(s)

evenly between the two end brackets and mark theirlocation. Mount into wood

whenever possible.

■Center the installation brackets on your marks and mark where to drill the screw holes.

➤A minimum ﬂat vertical surface of 30mm for installation brackets or extension brackets

isrequired.

➤The top of the installation brackets or extension brackets should be at the desired height.

The brackets should be level andaligned.

➤When using extension brackets, mark two screw holes per bracket.

CAUTION: The rear of the brackets must be ﬂush against a ﬂat mounting surface. Do not

mount brackets oncurved molding.

■Drill the screw holes using a 3mm drill bit.

CAUTION: Use drywall anchors when mounting into drywall.

Headrail End Marks

Window Opening

50mm Space Evenly Space Evenly 50mm

INSTALLATION

■Attach the installation or extension brackets using the screws provided.

IMPORTANT: The front edges of the brackets

must be level and aligned to each other.

■If using spacer blocks, ﬁrst attach the installation bracket to the

13mm spacer block before stacking additional spacer blockstogether.

➤Insert the legs of the installation bracket into the tabs on the

spacer block.

➤Then rotate the installation bracket back.

■Attach the spacer block and installation bracket to

a ﬂat vertical mounting surface with a #6mounting

screw long enough for asecure installation.

➤A maximum of 38mm of spacer blocks per

installation bracket is recommended.

➤The top of the spacer blocks should be at the

desired shade height.

IMPORTANT: The front edges of the installation

brackets must be level and aligned to each other.

CAUTION: Use drywall anchors when mounting

into drywall.

■If using extension brackets, attach an installation

bracket to the underside of each extension bracket

using theprovided screws and speed nuts.

Proceed to “Install the Shade” on page 9.

Tab

Longer Screw

(Not Provided)

Maximum

38mm

INSTALLATION

Mount the Installation Brackets — EndMount

End mount the headrail when conventional mounting techniques will not work — for example, in an

arched window opening.

■Position the end mount brackets so that the top of the attached installation brackets are at the

ordered height of the shade.

CAUTION: Both brackets must be installed at the same

depth and height.

■Mark both screw holes.

➤The mounting surface must be vertical and ﬂat, not

part of an archedcurve.

➤Minimum mounting depth is 30mm for 20mm.

Minimum mounting depth for a fullyrecessed end

mount is 60mm for 20mm.

■Drill the screw holes using a 3mm drill bit.

■Attach the end mount installation brackets usingthe ﬂat

head

screwsprovided.

CAUTION: Drywall mounting is not recommended.

IMPORTANT: For instructions on installing an

arch over a rectangular shade, see the Installation,

Operation, and Care instructions that came with

your arch shade.

Proceed to “Install the Shade” on page 9.

30mm

Minimum

Ordered

Shade

Height

30mm

Minimum

Ordered

Shade

Height

Indice

Altri manuali LuxaFlex Tenda per finestra

LuxaFlex

LuxaFlex Duette Manuale utente

LuxaFlex

LuxaFlex RecessFix Manuale utente

LuxaFlex

LuxaFlex 410 Manuale utente

LuxaFlex

LuxaFlex Timber Venetians Manuale utente

LuxaFlex

LuxaFlex LiteRise Manuale utente

LuxaFlex

LuxaFlex Twist Series Manuale utente

LuxaFlex

LuxaFlex LUMINETTE Disegno dimensionale

LuxaFlex

LuxaFlex M25T Manuale utente

LuxaFlex

LuxaFlex EVO MagnaTrack Manuale utente

LuxaFlex

LuxaFlex 2106/56 Manuale utente

LuxaFlex

LuxaFlex Super Nova Guida utente

LuxaFlex

LuxaFlex Aluminium Venetians Manuale utente

LuxaFlex

LuxaFlex Roller blinds series Manuale utente

LuxaFlex

LuxaFlex Venetian Series Guida utente

LuxaFlex

LuxaFlex Nano Series Manuale utente

LuxaFlex

LuxaFlex Twist Manuale utente

LuxaFlex

LuxaFlex Timber Manuale utente

LuxaFlex

LuxaFlex Silhouette Shades Manuale utente

LuxaFlex

LuxaFlex Venetian Series Manuale utente

LuxaFlex

LuxaFlex Roman Series Manuale utente

LuxaFlex

LuxaFlex Silhouette Shadings Manuale utente

LuxaFlex

LuxaFlex Roman Blinds Guida utente

LuxaFlex

LuxaFlex SimpleFit Plisse Manuale utente

LuxaFlex

LuxaFlex Country Woods Venetians Manuale utente

Manuali Tenda per finestra popolari di altre marche

Jysk

Jysk ROGEN Manuale utente

SOMFY

SOMFY 1241752 Manuale utente

Rollos

Rollos S-Nanorollo V2 Guida alla pianificazione

Teptron

Teptron Move Manuale utente

Renson

Renson Outdoor Loggia Guida di sicurezza

Project Source

Project Source CDLF2342W Manuale utente

Domondo

Domondo PureNight Manuale di istruzioni per l'installazione

rollease acmeda

rollease acmeda Easy Spring Air Guida all'installazione

IKEA

IKEA KADRILJ Manuale utente

Hallis Hudson

Hallis Hudson Rolls Super glide Manuale utente

Benthin

Benthin P1614 Manuale utente

MV LINE

MV LINE CLARA 015 Manuale di istruzioni

Current

Current E-WAND Guida

weinor

weinor VertiTex ZipR Manuale

Roto

Roto ZAR M R4/R7 Manuale utente

SOMFY

SOMFY Movelite WT Series Manuale utente

Acmeda

Acmeda RF400 Series Manuale utente

Motura

Motura Pli_353/3 Manuale utente