LxR AB-100 Manuale utente

AB-100 Amplifier

User Guide

1. Getting started

Please put your AB-100 Amplifier (machine) on a plat and stable surface. Avoid direct sunlight, heat and moisture.

Make sure the room is ventilated to ensure the full operation of the chiller. Make sure the machine is turned off

before plugging in.

The RCA jacks and torque guards on this machine has different colors for easily setup. The right channel jack is red,

and the left is black. Please use the best quality signal cables, power cables and speaker cables. Make sure all

cables are flawless, and fully plugged in.

Please unplug the machine should it be unused for a certain period of time.

※Do not open the shell. Any deconstruction or reconstruction of the machine will have unpredictable results. LxR

holds no responsibility should the machine be damaged due to such conducts.

AB-100 Amplifier is not designed for self repair. Please contact technicians for any problems.

※Clean the machine only with dry soft cloth.

※Do not use benzoyl or volatile solvents on the machine.

※This User Guide is for AB-100 only. LxR will not voluntarily notify any changes in appearance or specifications.

2. Contents

‧AB-100 Amplifier

‧Power cable

‧Remote x1

‧User guide, Warranty Card

※If there is anything missing, please contact your local dealer or agents.

3. Machine Installation

(1) Plug in the power cable to the machine and the power outlet.

(2) Plug the speaker cable to the speak outlet, and the signal cable to the signal outlet on the rear panel.

※Make sure it is fasten well to avoid poor connection. When connecting the RCA, make sure analog signal cable is

accurately connect.

(3) Press Remote or the Power button on the panel to turn on AB-100, and switch to the desire signal.

1. Power switch

Switch to turn on the machine, and wait for the blue LED light. Switch again to turn off.

2. Infrared remote receiver

There is a infrared sensor behind the red window to receive orders from the remote control.

※There must be no barriers between the remote control and this receiver to ensure full

connection. Should there be barriers, the remote control will fail to function.

3. Display indicator

The blue indicator will light up when mode is in use.

4. Input

Turn the input button clock-wise to switch to AB-100. The audio switch controller on the

remote control has the same function.

5. Volume

To adjust the volume of the speaker. You can also choose to use the remote control to adjust

the volume.

6. RCA Connector

There are four RCA connectors to support analog signal connector.

7. Speaker protection connector

The speaker protection connector can reset the speaker, when the speaker can not play the

music smoothly.

8. Speakers connector

Connect the right channel speaker to the connector with R+ and R-; connect the left channel

speaker to the connector with L+ and L-.

9. AC input

Only use the power cable provided by LxR or cables that meet safety requirements.

※Make sure your power cable is well fasten to avoid misconnection, and all wires are attached

prior to turning on the power.

Graph 2: 6. RCA connector

7. Speaker protection connector

8. Speaker connector

9. AC input

Graph 1: 1. Power switch

2. Infrared remote receiver

3. Display indicator

4. Input

5. Volume

Panel Applications

Graph 1

Graph 2

The Remote Control

1. POWER: on and off

2. VOL: Volume adjustor Vol+/Vol-

3. MUTE : mute

4. SELECT: Mode switch

AB-100 Specifications

1. Output power: AB 100W+100W/4Ω

2. RCA jack: 4

3. input impedance: 470KΩ

4. Frequency response: 10Hz-60KHz

5. Power: AC 110V/60Hz

6. Size:L420mmxW390mmxH97mm

7. Weight: +(-)13KG

Trouble Shooting

In case of error, please check the follow items. Most errors occur due to malfunction or

misconnection. Should errors remain unsolved, please contact your local dealer or LxR

technical service.

Error Indicator Solution

No power 1.

Is the power cable connected?

1. Connect the power cable.

No sound

Is the signal cable and the

speaker cable well connected?

Is the input mode correct?

Is the volume appropriate?

Speaker protection function

Connect the signal cable and

speaker cable.

Select the correct mode.

Adjust the volume to the

appropriate range.

Reset the speaker protection

connector (use a sharp tip to

press no. 7 on the panel)

No sound in one

channel

Is one side of the channel

misconnected?

Is one side of the speaker

misconnected?

Connect the signal cable.

Connect the speaker cable.

There’s a loud buzz

sound

Poor connection, not fasten

well, or poor quality of the

cable wire?

Fasten the signal cable tightly, or

replace it

Remote control fails

to function

Is there a button stuck?

Is there no power?

Press the button again.

Replace battery.

L x R O r g i n a l A u d i o A m p l i f i e r T E L ：(02)2904-6299

New North R oa d No. 458, 1 st Floor , seve n new T a ip ei X i nzhu an g D i strict w w w .lx r.c om . tw

Indice

Altri manuali LxR Amplificatore

LxR

LxR POWER X50 Series Manuale utente

Manuali Amplificatore popolari di altre marche

ASTRO

ASTRO HVO V40 P Manuale utente

Marantz

Marantz SUPERSCOPE BLA-545 Istruzioni per il montaggio

NAD

NAD CI980 Manuale utente

Technics

Technics SE-CH770 Manuale utente

Harman Kardon

Harman Kardon HK6300 Manuale utente

NAD

NAD T975 Manuale utente

McIntosh

McIntosh MA6850 Manuale utente

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuale utente

Viatron

Viatron Autrix Manuale utente

GME

GME GA9800 Manuale utente

Atlas

Atlas CP700 Manuale utente

Roland

Roland KC-1000 Manuale utente

Pyle

Pyle PFMRA350BW Manuale utente

Advantage

Advantage S-250 Manuale utente

IRT Electronics

IRT Electronics DVA-3007 Manuale utente

Dimavery

Dimavery BA-100 Series Manuale utente

Sony

Sony XM-S400D Manuale utente

Schertler

Schertler ROY X Manuale utente