Lynx LEH39 Manuale utente

LEH CARE & USE/INSTALLATION |1

MAKE THE MOST OF YOUR

LEH39/61 CARE & USE/INSTALLATION

Lynx Electric Infrared Heater

|LEH CARE & USE/INSTALLATION

Clearance from Combustibles 3

Warnings 4

Installation Instructions 5

Wiring Instructions 5

Mounting Instructions 6

Replacement Element Installation 7

Replacement Parts 7

Heater Coverage Areas 8

General Notes 8

Maintenance Instructions 8

Trouble Shooting 9

Location Suggestions 9

Warranty 10

TABLE OF CONTENTS

This use & care manual covers the Lynx heater models listed below. Some features and options will vary based upon

the model that you purchased.

LYNX ELECTRIC HEATER MODELS

39" 61"

LEH39 LEH61

LEH CARE & USE/INSTALLATION |3

CLEARANCE FROM COMBUSTIBLES

SAVE THIS MANUAL FOR FUTURE REFERENCE

• For Wall-Mounting, do not install heater closer than 18" (45.7cm) from adjacent walls and 6" (15.2cm) from

ceiling and do not install less than 6' (1.8m) if the heater is labeled as UL Listed and 8' (2.4m) if the heater is

labeled as UL/CUL Listed from ﬂoor, while heater is set at a downward angle of 30 to 60 degrees.

• For Ceiling-Mounting, do not install heater closer than 18" (45.7cm) from adjacent walls and 6" (15.2cm)

from ceiling and do not install less than 6' (1.8m) if the heater is labeled as UL Listed and 8' (2.4m) if the

heater is labeled as UL/CUL Listed from ﬂoor, while heater is at a maximum 30 degrees.

• Adjacent Heaters to be installed no less than 3' (0.9m) apart.

• Do NOT operate within 25' (7.6m) of ﬂammable/explosive material.

• Never block heater.

• Heaters greater than 240 Volts are for “Commercial Use Only. Risk of ﬁre. Do not use as a residential or

household heater.”

• A means for disconnection of the appliance must be incorporated in accordance with the local wiring codes.

• Do not use if the heating element is damaged or cracked.

CLEARANCE FROM COMBUSTIBLES:

MIN. 18" (45.7cm)

FROM SIDES AND

ENDS OF HEATER

MIN. 36" (91.4cm)

IN FRONT OF HEATER

MIN. 6" (15.2cm)

CLEARANCE

BEHIND HEATER

“IMPORTANT INSTRUCTIONS”

“SAVE THESE INSTRUCTIONS”

WARNINGS- Read all instructions before using heater:

Unit may be a source of possible shock. NEVER attempt to service heater without disconnecting its power source. Source

of possible ignition.

CAUTION-High Temperature, risk of ﬁre, keep electrical cords, drapery, furnishings and other combustibles at least 3'

(0.9m) from the front of heater and away from sides and rear.

MOUNTING HEIGHT/CLEARANCES

|LEH CARE & USE/INSTALLATION

WARNINGS

WARNING

• Children should never be left alone or unattended in an area where this appliance is located. Install

your heater well away from areas where children play. Do not store items that may interest children in or

around the area of your heater.

• Never touch the heater face when hot. When in use, portions of the heater are hot enough to cause

severe burns.

• Always maintain the required clearances from combustibles as detailed. The heater is designed for

indoor or outdoor use.

• Electric heaters are not to be installed in or on recreational vehicles, portable trailers, boats or any other

moving installation.

• Keep any electrical supply cord away from any heated surfaces.

• Do not repair or replace any part of the heater unless speciﬁcally recommended in this manual. Other

service should be performed by a qualiﬁed technician.

• This appliance must be installed by a professional installer or technician.

• Product installation must meet local electric codes or, in the absence of local codes, the latest edition of the

National Electrical Code ANSI/NFPA No. 70 or the Canadian Electrical Code CSA C22.1.

• Unit may be a source of possible shock. NEVER attempt to service heater without disconnecting its power

source. Source of possible ignition.

• High Temperature, risk of ﬁre, keep electrical cords, drapery, furnishings and other combustibles at least 3'

(0.9m) from the front of heater and away from sides and rear.

THIS MANUAL MUST REMAIN WITH THE PRODUCT OWNER FOR FUTURE REFERENCE.

READ THIS MANUAL CAREFULLY and completely before using your heater to reduce the risk of:

1. Fire

2. Burn hazard, personal injury or property damage

3. Unapproved installation or servicing.

Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death.

Read this manual thoroughly before installation, use, or servicing of this product.

WARNING

If not installed, operated and maintained in accordance with the manufacturer’s instructions, this product can

expose you to chemicals including nickel, which are known to the State of California to cause cancer and birth

defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

WARNING

LEH CARE & USE/INSTALLATION |5

This heater must be permanently installed and hard wired by a licensed electrician in accordance with local

electrical codes. Assembly procedure must be performed with no electrical power to unit.

Step 1: Check UL/CUL/CE label on heater for proper voltage.

Step 2: Follow supplied wiring instructions. (See wiring instructions below)

Step 3: Heater must be mounted with reﬂector angled down.

Step 4: All electrical connections must be in compliance with the National Electric Code (NEC) and local codes

for outdoor wiring.

Step 5: Use only wiring components UL/CUL/CE listed for outdoor use with IPX4 minimum rating.

WIRING INSTRUCTIONS

The heater is drilled and threaded for standard 1/2" conduit ﬁttings. The installing electrician will need to

provide the appropriate rigid metallic, ﬂexible or liquid tight conduit for the installation location.

• Observe local electrical code regulations.

• Remove cover plate from junction box.

• Attach conduit.

• Use only copper wire suitable for 90°C.

• Replace cover plate.

Connect power with

ﬂexible conduit or

appropriate cord to allow

heater to be swiveled. The Junction Box inlet

hole is sized for a standard

½” weather tight conduit

ﬁtting and has a locknut

located on the inside of the

box for fastening.

INSTALLATION INSTRUCTIONS

WIRING INSTRUCTIONS

Duplex Stack Switch is Included with the heater.

Green ground

wire screw

Junction Box on top of the

heater has a gasket side

access cover.

|LEH CARE & USE/INSTALLATION

MINIMUM 18"

72" (1.8m) MINIMUM

HEIGHT FROM FLOOR

6-3/8" (15.2cm) LEVEL HERE

WALL

CEILING

60º MAX.

AIM POINT

WALL OR CEILING SWIVEL

MOUNTING BRACKETS (PAIR)

6" MOUNTING SURFACE

TO REAR OF HEATER

8" WIDE

LENGTH VARIES DEPENDING ON

MODEL (MAX. 61-1/4")

INSULATED HOUSING

WALL

CEILING

60º MAX.

AIM POINT

WALL OR CEILING SWIVEL

MOUNTING BRACKETS (PAIR)

6" MOUNTING SURFACE

TO REAR OF HEATER

8" WIDE

LENGTH VARIES DEPENDING ON

MODEL (MAX. 61-1/4")

INSULATED HOUSING

These models may be chain or bracket mounted to any ceiling or horizontal surface. Installation must be such

that 18" (45.7cm) minimum clearance is maintained around the heater on all four sides and 36" (91.4cm) directly

in front. A minimum of 6" (15.24cm) of clearance provided by mounting brackets is required behind the plane of

the face. Heater can be hung using chains or custom brackets. Heater must be level, but can be rotated around

its horizontal axis.

Heater must be installed with the quartz tube horizontally level. For maximum tube life, use a carpenter’s level

tool to ﬁnd the optimum level position for the heater’s body. Always maintain the minimum clearances from the

heater body to any combustible materials.

3" (7.6cm)

8-3/16"

(20.2cm)

5-3/8"

(13.6cm)

SWIVEL MOUNTING

BRACKETS (CEILING OR

WALL MOUNT)

LENGTH WILL VARY

DEPENDING ON MODEL

INSULATED HOUSING 6" (15.2cm)

9-3/8"

(23.8cm)

(45.7cm)

FROM SIDE

(45.7cm)

FROM SIDE

MINIMUM 18"

MOUNTING INSTRUCTIONS

LEH CARE & USE/INSTALLATION |7

11/32" OUTSIDE NUT

11/32" INSIDE NUT

(SNUG TO CERAMIC)

Disconnect the power at the breaker. Remove the grill by grasping it in the middle, ﬂex grill up and lift it off.

Unscrew and remove both end reﬂectors. Unhook element clips at each end of the heater and remove nuts from

end of element to remove the existing quartz tube. Carefully install the new element. Remove one nut from end of

the new element. Install wire by sliding high temperature ring terminal onto element screw and replace nut. Use a

thin 11/32" wrench to hold inside nut. Nuts must make a tight connection. Close element clips over tube, reinstall

end reﬂectors, then snap protective grill back in place.

NOTE: Hold ceramic element ﬁrmly while

tightening nut to prevent damage to

element. Nut should be tightened snug.

A loose connection can cause the

element to short or fail prematurely.

REPLACEMENT ELEMENTS

PART NUMBER ELEMENT NUMBER LENGTH WATTS VOLTS FITS

LERE2024 E-2024 36" (0.9m) 2000 240 LEH39

LERE3024 E-3024 58" (1.5m) 3000 240 LEH61

PART NUMBER PART DESCRIPTION QUANTITY NEEDED

36523 Dual Element End Reﬂector (Set of 2) 1

36525 Body Reﬂector – Fits 39" (1.0m) 1

36526 Body Reﬂector – Fits 61-1/4" (1.6m) 1

36528 Grill Guard – Fits 39" (1.0m) 1

36529 Grill Guard – Fits 61-1/4" (1.6m) 1

36531 Lead Wire Set – Fits 39" (1.0m)* 2

36532 Lead Wire Set – Fits 61-1/4" (1.6m)* 2

36533 SS Mounting Bracket (Set of 2) 1

FMKIT39 Flush Mount SS Plaster Frame – Fits 39" (1.0m) 1

FMKIT61 Flush Mount SS Plaster Frame – Fits 61-1/4" (1.6m) 1

* Note: Dual Element Heaters require 2 Lead Wire Sets per Heater

REPLACEMENT ELEMENT INSTALLATION

REPLACEMENT PARTS (see diagram on page 12)

|LEH CARE & USE/INSTALLATION

MODEL WATTS MOUNTING HEIGHT AVERAGE COLD PROTECTED

LEH39 4,000 8' - 12' (2.4m - 3.7m) 8' x 10' (2.4m x 3.0m) 6' x 8' (1.8m x 2.4m) 10' x 12' (3.0m x 3.7m)

LEH61 6,000 10' - 14' (3.0m - 4.3m) 11' x 11' (3.4m x 3.4m) 10' x 10' (3.0m x 3.0m) 12' x 12' (3.7m x 3.7m)

• LYNX QUARTZ TUBE ELECTRIC HEATERS are furnished with wall/ceiling mount swivel brackets. These brackets

may be discarded when the heater is hung with chains, special bracketing, or used in conjunction with our ﬂush

mount frame.

• See sales literature and price list for full listing of models, descriptions, amperages, and voltages. At times,

especially when the mounting height might be quite low, an increased number of smaller heaters can help prevent

overheating.

• Dual Element Heaters can be wired with our Duplex/Stack Switch (provided see pg.5) which enables the ability to

turn on and off each element independently, providing for half power/full power capabilities.

• For ideal comfort heat, the best solution is to heat from two sides rather than from just one side. However, there are

times when this is not practical.

• Coverage areas are approximate dimensions and will vary depending on prevailing and personal comfort levels.

• Indoor or well-protected environments will generally exceed average (see charts). Heaters can provide less than

average coverage in extremely cold/windy conditions.

• Before performing any maintenance, power must be disconnected and the heater cool to touch.

• Heater housing, reﬂectors, and heating element can be rinsed with a hose or wiped down with isopropyl

alcohol, acetone, or glass cleaner. Use a clean, scratch-free rag or paper towel. Any oxidation, surface rust, or

discoloration can be removed with a stainless steel cleaner or metal polish on the bare metal surface.

• Make sure all water, solvents, or cleaners are removed and the heater is dry before reconnecting the power.

NOTE: Mounting height should not be less than 6' (1.8m) if the heater is labeled as UL Listed and 8' (2.4m) if the

heater is labeled as CUL Listed. Indoor or well-protected environments will generally exceed average.

Heaters can provide less than average coverage in extremely cold/windy conditions.

HEATER COVERAGE AREAS

DUAL ELEMENT AREAS COVERED (FEET)

MAINTENANCE INSTRUCTIONS

GENERAL NOTES

LEH CARE & USE/INSTALLATION |9

PROBLEM

Heater does not glow

Low heat output

Heater does not work

WHAT TO DO

• Check supply voltage to conﬁrm it matches voltage of heating element.

• A 240V element connected to 110V or 208V will warm, but not glow orange

or generate sufﬁcient heat for typical applications (Matching your voltage is

extremely important). If element is visibly orange, but there is insufﬁcient heat,

refer to the areas covered with respect to conditions and mounting heights.

• Replace or clean dirty or non reﬂective reﬂectors.

• Disconnect power and check element with an ohm meter for continuity. If there

is any continuity across the bulb, the problem is in the wiring/controls.

• Check that there is proper voltage to the heater.

• Check that the control/switch is working.

• Check main power circuit breaker.

• Check wiring for a loose connection or burned wire.

Unless heaters are installed over 12' (3.7m) high, it is generally recommended that all radiant heaters be

mounted on an angle to assure that radiant warmth is distributed from the sides rather than straight down on the

heads and shoulders of the people being warmed.

Angle ﬁxture 30º to 60º from

horizontal face down. Best

angle is approximately 45º.

RECOMMENDED POSITIONING INSTALLATION DIRECTION OUTDOORS

TROUBLESHOOTING

LOCATION SUGGESTIONS

TROUBLESHOOTING

Install ﬁxture to heat the area from

the "cold side" if possible. This helps

compensate for increased body heat

losses due to exposure. Warm ﬂoors

re-radiate heat. Warmer air rises from

the ﬂoor. Some heat reﬂects from the

ﬂoor. Mounting a heater directly over a

table or other obstruction will block the

energy, primarily heating the object. It is

best to move heater to the side, allowing

complete body and ﬂoor coverage.

When outdoors, hang heater under

protective roof or wether cover

whenever possible. Even though

heater is all-weather construction, it

will last longer and look better if it is

protected from rain and snow.

|LEH CARE & USE/INSTALLATION

VISIBLE LOSS OR DAMAGE

Be certain any visible damage to the carton is noted on

freight bill or express receipt and signed by the person

making delivery.

FILE CLAIM FOR DAMAGES IMMEDIATELY, regardless of

extent of damage.

CONCEALED LOSS OR DAMAGE

If damage is unnoticed until the heater is unpacked, notify

the transportation company or carrier immediately and ﬁle

a “concealed damage” claim with them. This should be

done within (5) days of the date delivery is made to you. Be

sure to hold on to the container for inspection. We cannot

assume responsibility for damage or loss incurred in transit.

TROUBLESHOOTING

...continued

Important: Please retain original proof of purchase to establish warranty period.

Any implied warranties of merchantability and ﬁtness applicable to the equipment are limited in duration to the period of

coverage of this express written warranty. This warranty grants speciﬁc legal rights to the purchaser. Other rights, which may

vary from state to state, may also apply. Title to the merchandise passes to the consignee upon acceptance by the carrier.

After acceptance by the carrier, the merchandise travels at the risk of the

purchaser. In the event of freight damage, do not refuse shipment. Advise both the freight agent and the shipper of the

damage. Note the details of that damage on the freight bill before any freight charges are paid and ﬁle a claim for damages

with the freight agent.

Before calling Lynx Customer Care, please make sure you

have the following information:

• Model number

• Date of purchase

• Proof of purchase by the original owner

• Serial number

For warranty service, contact the Lynx Customer Care

Department for an authorized service agent near you at:

(888) 289-5969

www.lynxgrills.com

Your satisfaction is of the utmost importance to us. If a

problem cannot be resolved to your satisfaction, please

write, fax or email us:

Lynx Professional Grills

7300 Flores Street

Downey, CA 90242

Service: (888) 289-5969

Tel: (562) 299-6900

Fax: (562) 299-6978

email: [email protected]

www.lynxgrills.com

CONTACTING LYNX CUSTOMER CARE

SHIPMENT DAMAGES

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Lynx Stufa

Lynx

Lynx LHEM48 Manuale utente

Manuali Stufa popolari di altre marche

oventrop

oventrop Regucor Series Manuale utente

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuale utente

ELMEKO

ELMEKO ML 150 Manuale utente

BN Thermic

BN Thermic 830T Manuale utente

KING

KING K Series Guida

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guida rapida

Well Straler

Well Straler RC-16B Manuale utente

EUROM

EUROM 333299 Manuale utente

Heylo

Heylo K 170 Manuale utente

Eterna

Eterna TR70W Manuale utente

Clarke

Clarke GRH15 Manuale di istruzioni

IRSAP

IRSAP The Radiator Company Ovali Manuale utente

Empire Heating Systems

Empire Heating Systems WCC65 Manuale utente

Wetekom

Wetekom 92 86 43 Manuale utente

Desa

Desa SPC170-F Manuale utente

Watlow

Watlow Watrod Electric Tubular Heaters Manuale utente

Haverland

Haverland ECO-DRY GPS Series Manuale elenco delle parti

Stelpro

Stelpro ASILVC2060 Series Manuale utente