M-system R3-PC16A Manuale utente

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8408 Rev.5 P. 1 / 4

INSTRUCTION MANUAL

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Pulse output module ...........................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

• The equipment must be mounted inside the instrument

panel of a metal enclosure.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

■HOT SWAPPABLE MODULES

• Replacing the module does not affect other modules on

the same base. Thus, the module can be replaced while

the power is ON. However, replacing multiple modules

at once may greatly change live voltage levels. We highly

recommend to replace them one by one.

■GENERAL PRECAUTIONS

• DO NOT set the switches on the module while the power

is supplied. The switches are used only for maintenance

without the power.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

INSTALLATION

Use the Installation Base (model: R3-BSx).

PULSE OUTPUT MODULE

(open collector output, 16 points) MODEL R3-PC16A

R3-PC16A

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8408 Rev.5 P. 2 / 4

COMPONENT IDENTIFICATION

RUN LED

ERR LED

Status Indicator LED

■FRONT VIEW ■SIDE VIEW

SW1SW2

SW3

1Count

Reset

OFF

Width

Count Reset SW must be turned off during operation.

■STATUS INDICATOR LED

RUN indicator: Bi-color (red/green) LED;

Red when the bus A operates normally;

Green when the bus B operates normally;

Amber when both buses operate normally.

ERR indicator: Bi-color (red/green) LED;

Red with external power supply abnormal-

ity;

Green in normal operating conditions.

Output status indicator: Red LED; turns on with the output

ON.

■SIDE DIP SW

(*) Factory setting

• ON/OFF Pulse Width: SW1-1 through 1-6

ON OFF PULSE WIDTH TIME *1

123456

OFF OFF OFF OFF OFF OFF 5 msec. (*)

ON OFF OFF ON OFF OFF 10 msec.

OFF ON OFF OFF ON OFF 50 msec.

ON ON OFF ON ON OFF 100 msec.

OFF OFF ON OFF OFF ON 500 msec.

ON OFF ON ON OFF ON 1 sec.

OFF ON ON OFF ON ON 1.5 sec.

ON ON ON ON ON ON 2 sec.

*1. Minimum ensured time duration. For example, with 5

msec. setting, the minimum pulse width is 5 msec. and the

maximum 7 msec. (approx.)

• Count Reset: SW3-1

SW COUNT RESET

NORMAL COUNT RESET

SW3-1 OFF (*) ON

Note 1: Be sure to turn OFF during use.

Note 2: Be sure to set unused SW1-7, 1-8, SW2 and SW3-2

through 3-4 to OFF.

PC CONFIGURATOR

With conﬁgurator software, settings shown below are available.

Refer to the software manual of R3CON for detailed operation.

• Maximum count limit: 1 to 65,535 (factory setting: 10,000)

R3-PC16A

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8408 Rev.5 P. 3 / 4

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■EXTERNAL DIMENSIONS unit: mm (inch)

130 (5.12)

27.5 (1.08) 109 (4.29)

POSITIONING

GUIDE

TERMINAL

COVER

20–M3

SCREW

6.2

(.24)

■CONNECTION DIAGRAM

INTERNAL BUS A

INTERNAL POWER

INTERNAL BUS B*

*For dual redundant communication.

BUS CONNECTOR

Po 1

Po 16

Po 15

Po 14

Po 13

Po 12

Po 11

Po 10

Po 9

8Po 8

7Po 7

6Po 6

5Po 5

4Po 4

3Po 3

2Po 2

24V DC

COM

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.5 N·m

■SOLDERLESS TERMINAL

Refer to the drawing below for recommended ring tongue

terminal size. Spade tongue type is also applicable. Solder-

less terminals with insulation sleeve do not ﬁt.

Applicable wire size: 0.3 – 0.5 mm2

Recommended manufacturer: Japan Solderless Terminal

MFG. Co., Ltd., Nichifu Co., Ltd.

12max

6max

3max 4min

3.2 dia.

(mm)

R3-PC16A

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8408 Rev.5 P. 4 / 4

OPERATING MODES

When writing the number of output pulse (target value)

from a host, R3-PC16A outputs the difference from the

number of pulse outputs until now (present value) as the

remainder number of pulse.

The present value of the R3-PC16A is held even with power

off. If target value is ‘0’ or higher than totalized pulse up-

per limit, it is invalid. When the target value is not less

than 2001 for the present value, the unit does not output

the pulse and the present value is equal to the target value.

E.g.1) Present value = 1000 and target value = 1500, it out-

puts 500 pulses.

E.g.2) Present value = 9000 and target value = 500, it out-

puts 1500 pulses.

E.g.3) Present value = 1000 and target value = 3001, it

does not outputs any pulse, present value = 3001.

(When the totalized pulse upper limit is initial setting,

10000.)

MANUAL COUNT RESET

1) Remove Network Module or its cables and interrupt com-

munication with other devices.

2) Turn ON the Count Reset SW (SW3-1).

3) Return the module to the base and turn the power supply

on.

4) ERR LED turns on and the module starts resetting its

counter. When the resetting is complete, the LED turns

to green. DO NOT remove the power while the red LED

is on. The RUN LED starts blinking at the same time.

5) After the green LED is conﬁrmed, turn the power supply

off.

6) Turn OFF the Count Reset SW (SW3-1).

7) Return the Network module onto the base and turn the

power supply on.

Note: Count Reset SW must be turned OFF after this proce-

dure because the module does not start counting with

ON state.

Altri manuali M-system Sistema I/O

M-system

M-system R7D-DC16B Manuale utente

M-system

M-system Remote I/O R8 Series Manuale utente

M-system

M-system R10M-CT4E Manuale utente

M-system

M-system R7E-PA8-R Manuale utente

M-system

M-system R3-SV16N Manuale utente

M-system

M-system R7 Series Manuale utente

M-system

M-system R80 Series Manuale utente

M-system

M-system Devicenet R7F4DD-DA16B-C Manuale utente

M-system

M-system Devicenet R7F4HD-DC32A Manuale utente

M-system

M-system R30PA2 Manuale utente

M-system

M-system R80YVT4N Manuale utente

M-system

M-system R7ML-LC2 Manuale utente

M-system

M-system R7M-DC8C Manuale utente

M-system

M-system R7ML-TS4 Manuale utente

M-system

M-system R30NE1 Manuale utente

M-system

M-system R3Y-SS16N Manuale utente

M-system

M-system R7 Series Manuale utente

M-system

M-system R8-CT4E Manuale utente

M-system

M-system R7M-CT4E-R Manuale utente

M-system

M-system R8-YVT4N Manuale utente

M-system

M-system M5SN Manuale utente

M-system

M-system R7D-TS4 Manuale utente

M-system

M-system JC-IO Manuale utente

M-system

M-system R3S-YV4 Manuale utente

Manuali Sistema I/O popolari di altre marche

WAGO

WAGO 750-344 Manuale utente

Teknim

Teknim TWM-1887 Manuale di istruzioni

Intelligent Appliance

Intelligent Appliance IA-2662-E Manuale utente

BERGHOF

BERGHOF ECC DIO 16/16 Manuale di istruzioni

Advantech

Advantech PCM-27J3AU Manuale di installazione e funzionamento

Festo

Festo CP-E08-M12-CL Manuale utente

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manuale utente

Hitachi

Hitachi HX-RIO3 Series Manuale utente

NUUO

NUUO SCB-A08 Manuale utente

jablotron

jablotron JB-110N Manuale utente

Omron

Omron SYSMAC C200H Manuale utente

DOLD

DOLD SAFEMASTER M Manuale utente

ABB

ABB OPT-MF-001 Manuale utente

Omron

Omron SYSMAC C2000H Manuale utente

Helmholz

Helmholz TB20 Manuale utente

ICP DAS USA

ICP DAS USA tM-AD2 Manuale utente

Automationdirect.com

Automationdirect.com DL305 Manuale utente

WAGO

WAGO I/O-SYSTEM 750 Manuale utente