Macurco CM-E1 Manuale utente

Macurco Security Series Detectors

CM-E1 Carbon Monoxide Detector

The CM-E1 is not intended for use in industrial

applications such as refineries, chemical plants and or

for use in parking garages as to control exhaust fans

The small, low profile unit is in a white plastic case. It

surface mounts to a wall using the supplied rear housing

or flush mounts in a 2 x 4 x1-1/2 inch deep single gang

switch or handy electrical box

Can be Field Tested with Carbon Monoxide Gas

900 square feet coverage

The CM-E1 is a low voltage detector of Carbon Monoxide. The CM–E1

is designed for connection to UL Listed Fire Alarm/Burglary Control

Panels. The CM-E1 is intended for non-hazardous locations such as

residences, retail stores, office buildings, and institutional buildings

Detector alarms at multiple levels

of exposure to carbon monoxide

based on time weighted averages

of the gas present

Listed to ULstandard 2075 for the

Standard For Safety for Gas and

Vapor Detector and Sensors

Tested to UL2075 using UL2034

Sensitivity limits for carbon

monoxide gas

The usual sources of Carbon monoxide are defective heat sources

such as furnaces or wood burning stoves and automobiles running in

adjoining garages. The CM-E1 can detect CO from these sources, as

well as any other sources of CO

CM-E1 Carbon Monoxide and Hydrocarbon Fuels

Carbon monoxide is an odorless, colorless and

toxic gas. Because it is impossible to see, taste or

smell the toxic fumes, CO can kill you before you

are aware it is present

At lower levels of exposure, CO causes mild effects

that are often mistaken for the flu. These symptoms

include headaches, dizziness, disorientation,

nausea and fatigue

Carbon monoxide is colorless, odorless gas

resulting from the incomplete combustion of

hydrocarbon fuels. Carbon monoxide interferes with

blood's ability to carry oxygen to the body's tissues

and results in numerous adverse health effects

CM-E1 Carbon Monoxide and Hydrocarbon Fuels

CM-6 Carbon Monoxide and Hydrocarbon Fuels

COLevelinAir HealthEffects

0ppm FreshAir

100ppm Slightheadacheafter1‐2hours.

200ppm Dizziness,headache,nauseaafter2‐3hours.

400ppm Dizziness,headache,nauseaafter1‐2hours/life

threateningafter3hours.

800ppm Dizziness,headache,nauseaafter45minutes,

unconsciousafter1hour,deathwithin3hours.

1,600ppm Dizziness,headache,nauseaafter20minutes,

deathwithin2hours.

3,200ppm Dizziness,headache,nauseaafter10minutes,

deathwithin60minutes.

6,400ppm Dizziness,headache,nauseaafter1‐2minutes,

deathwithin30minutes.

12,800ppm Instantaneouseffects,deathwithin3minutes.

The CM-E1 is programmed to alarm if the danger

levels of carbon monoxide are exceeded, which

are time and concentration-related.

The alarm points are in accordance with the

provisions of UL2034:

70 ppm of CO after 60 to 240 minutes

150 ppm of CO after 10 to 50 minutes

400 ppm of CO after 4 to 15 minutes

The CM-E1 continuously monitors the ambient air at the sensor. If the

CM-E1 measures levels of CO greater than the danger level, the RED

light will turn on, the Alarm Relay will switch to actuate the alarm

circuits in the control panel, and the buzzer on CM-E1 will sound.

CM-E1 Carbon Monoxide and Hydrocarbon Fuels

CM-E1 Carbon Monoxide Detector

Quickly press the TEST/RESETbutton 5 times.

The buzzer will do a quick double beep and the

LED will flashAmber alternating with a pause

Aim the nozzle of the aerosol can at the buzzer

grate area and press for 4 to 5 seconds

Wait for a few seconds. The LED should blink

Green rapidly and the buzzer should double beep

every 15 seconds - Pass

Press the button once to return to normal mode

The CME1-FTG is an 11L 500 ppmAerosol Carbon Monoxide Field

Test Gas. This field test gas allows installers to do a Functional Test

of the CO sensor. The flow rate of the CME1-FTG is 10 LPM providing

enough gas to quick test 20-30 CM-E1 Carbon Monoxide sensors

GD-2B Combustible Gas Detector

Altri manuali per CM-E1

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Macurco Rilevatore di gas

Macurco

Macurco ND-2 Manuale utente

Macurco

Macurco DMK-1 Manuale utente

Macurco

Macurco AimSafety PM 100 Manuale utente

Macurco

Macurco CM-E1 Manuale utente

Macurco

Macurco GD-6 Manuale utente

Macurco

Macurco RD-6 Manuale utente

Macurco

Macurco TX-6-AM Manuale utente

Macurco

Macurco CM-6 Manuale utente

Macurco

Macurco TX-6-HS Manuale utente

Macurco

Macurco 6 Series Manuale utente

Macurco

Macurco GD-2A Manuale utente

Macurco

Macurco TX-6-ND Manuale utente

Macurco

Macurco CM-12 Manuale utente

Macurco

Macurco CD Series Manuale utente

Macurco

Macurco GD-6 Manuale utente

Macurco

Macurco TX-6-ND Manuale utente

Macurco

Macurco TX-6-AM Manuale utente

Manuali Rilevatore di gas popolari di altre marche

Evikon

Evikon E2632 Manuale utente

Critical Environment Technologies

Critical Environment Technologies CGAS-A Series Manuale utente

MSA

MSA altair 5 Manuale utente

DOD Technologies

DOD Technologies ChemLogic CL96 Manuale utente

DEGA

DEGA NS III LCD Series Manuale utente

RKI Instruments

RKI Instruments 35-3001A-08-01 Manuale utente

PEMTECH

PEMTECH PT2008 Series Manuale utente

Coster

Coster RGS 328 Manuale utente

Sygonix

Sygonix 2483186 Manuale utente

Perry

Perry 1GA 50917MET/P Manuale utente

isweek

isweek AS8900 Manuale utente

Oldham

Oldham OLC 10 Manuale utente

Wizmart

Wizmart NB983 Manuale utente

Beacon

Beacon MEGA Manuale

RKI

RKI GX-6000 Manuale utente

Dräger

Dräger PIR 7000 Manuale utente

GDS

GDS GASMAX EC Manuale utente

Seitron

Seitron BE COOL R1 Manuale utente