Magma 3TX Manuale utente
Thunderbolt™ 2
Installation Guide
Thunderbolt™ 2 Interface Card
Magma
Thunderbolt™ 2 Interface Card |
2
Contents
Safety Instructions ..................................................................................................3
Thunderbolt™ 2 for Roben-3........................................................................................5
Interface Card Installation........................................................................................5
Thunderbolt™ 2 for EB3T ............................................................................................8
Interface Card Installation........................................................................................8
Thunderbolt™ 2 for EB1T .......................................................................................... 11
Interface Card Installation...................................................................................... 11
Verify Installation..................................................................................................... 15
Hardware ............................................................................................................. 15
How to Get More Help ............................................................................................... 18
Contacting Technical Support ................................................................................. 18
Returning Merchandise to MAGMA ...........................................................................18
Magma
Thunderbolt™ 2 Interface Card |
3
Safety Instructions
Always use caution when servicing any electrical component. Before handling the Magma Expansion chassis, read the
following instructions and safety guidelines to prevent damage to the product and to ensure your own personal
safety. Refer to the “Advisories” section for advisory conventions used in this manual, including the distinction
between Danger, Warning, Caution, Important, and Note.
1. Always use caution when handling/operating the computer. Only qualified, experienced, authorized electronics
personnel should access the interior of the computer and expansion chassis.
WARNING
Never modify or remove the radio frequency interference shielding from your workstation or
expansion unit. To do so may cause your installation to produce emissions that could interfere with
other electronic equipment in the area of your system.
When Working Inside a Computer
1. Before taking covers off a computer, perform the following steps:
2. Turn off the computer and any peripheral devices.
3. Disconnect the computer and peripheral power cords from their AC outlets or inlets in order to prevent
electric shock or system board damage.
In addition, take note of these safety guidelines when appropriate:
To help avoid possible damage to systems boards, wait five seconds after turning off the computer before
removing a component, removing a system board, or disconnecting a peripheral device from the computer.
When you disconnect a cable, pull on its connector or on its strain-relief loop, not on the cable itself. Some
cables have a connector with locking tabs. If you are disconnecting this type of cable, press in on the
locking tabs before disconnecting the cable. As you pull connectors apart, keep them evenly aligned to avoid
bending any connector pins. Also, before connecting a cable, make sure both connectors are correctly
oriented and aligned.
CAUTION
Do not attempt to service the system yourself except as explained in this manual. Follow installation
instructions closely.
Magma
Thunderbolt™ 2 Interface Card |
4
Protecting Against Electrostatic Discharge
Electrostatic Discharge (ESD) Warning
Electrostatic Discharge (ESD) is the enemy of semiconductor devices. You should always take
precautions to eliminate any electrostatic charge from your body and clothing before touching any
semiconductor device or card by using an electrostatic wrist strap and/or rubber mat.
Static electricity can harm system boards. Perform service at an ESD workstation and follow proper ESD procedures
to reduce the risk of damage to components. Magma strongly encourages you to follow proper ESD procedures,
which can include wrist straps and smocks, when servicing equipment.
You can also take the following steps to prevent damage from electrostatic discharge (ESD):
When unpacking a static-sensitive component from its shipping carton, do not remove the component’s anti-
static packaging material until you are ready to install the component in a computer. Just before
unwrapping the anti-static packaging, be sure you are at an ESD workstation or are grounded.
When transporting a sensitive component, first place it in an anti-static container or packaging.
Handle all sensitive components at an ESD workstation. If possible, use anti-static floor pads and workbench
pads.
Handle components and boards with care. Don’t touch the components or contacts on a board. Hold a
board by its edges or by its metal mounting bracket.
Magma
Thunderbolt™ 2 Interface Card | Thunderbolt™ 2 for Roben-3
5
Thunderbolt™
2for Roben-3
Interface Card Installation
Uninstall the existing Thunderbolt Interface card in the chassis prior to installing the new Thunderbolt™ 2
Interface card.
WARNING
High voltages are present inside the expansion chassis when the unit’s power cord is plugged into
an electrical outlet. Disconnect the power cord from the AC outlet before removing the enclosure
cover. Turning the system power off at the power on/off switch does not remove power to
components. High voltage is still present.
1. Remove the screw on top of the mounting bracket.
2. Disconnect the 3-pin wire / power cable from the Interface card, as shown from pictures below.
3. Gently pull the Thunderbolt Interface card out in the PCIe slot.
4. Prepare the new Thunderbolt™ 2 Interface card (see picture below).
Magma
Thunderbolt™ 2 Interface Card | Thunderbolt™ 2 for Roben-3
6
5. Align the Thunderbolt™ 2 Interface card on top of the PCIE slot.
6. Gently push the card until it is firmly seated in the PCIe slot.
7. Reconnect the 3-pin wire / power cable to Thunderbolt™ 2 Interface card (see pictures below).
8. Secure the Thunderbolt™ 2 Interface card.
Magma
Thunderbolt™ 2 Interface Card |
7
NOTE
The new Thunderbolt™ 2 Interface card is shorter that the old Thunderbolt™ 1 Interface card.
.
Thunderbolt™ 1
Thunderbolt™ 2
Vendor ID (Magma)
0X19
0X19
UID
0X00190003
0X00190008
Mac OS Supported
10.8 below
10.9 and above
Speed
10Gb/s
20Gb/s
Lane width
X4
X4
# of LEDs
5
10
Magma
Thunderbolt™ 2 Interface Card |
8
Thunderbolt™
2for EB3T
Interface Card Installation
Uninstall the existing Thunderbolt Interface card in the chassis prior to installing the new Thunderbolt™ 2 Interface
card.
WARNING
High voltages are present inside the expansion chassis when the unit’s power cord is plugged into
an electrical outlet. Disconnect the power cord from the AC outlet before removing the enclosure
cover. Turning the system power off at the power on/off switch does not remove power to
components. High voltage is still present.
1. Remove the screw on top of the mounting bracket.
2. Disconnect the 3-pin wire / power cable from the Interface card, as shown from pictures below.
3. Gently pull the Thunderbolt™ 1 Interface card out in the PCIe slot.
4. Prepare the new Thunderbolt™ 2 Interface card.
Magma
Thunderbolt™ 2 Interface Card | Thunderbolt™ 2 for EB3T
9
5. Align the Interface card on top of the PCIE slot.
6. Gently push the card until it is firmly seated in the PCIe slot
7. Reconnect the 3-pin wire / power cable to Thunderbolt™ 2 Interface card (see pictures below).
8. Secure the interface card.
Magma
Thunderbolt™ 2 Interface Card |
10
NOTE
The new Thunderbolt™ 2 Interface card is shorter that the old Thunderbolt™ 1 Interface card.
.
Thunderbolt™ 1
Thunderbolt™ 2
Vendor ID (Magma)
0X19
0X19
UID
0X00190003
0X00190008
Mac OS Supported
10.8 below
10.9 and above
Speed
10Gb/s
20Gb/s
Lane width
X4
X4
# of LEDs
5
10
Questo manuale è adatto per i seguenti modelli
7
Indice
Altri manuali Magma Hardware per computer
Magma
Magma PE6R4-I Manuale utente
Magma
Magma ROBEN Series Manuale utente
Magma
Magma EB4-1U Manuale utente
Magma
Magma EB7-X8G2 Manuale utente
Magma
Magma Roben-3TX Manuale utente
Magma
Magma PE6R4-I Manuale utente
Magma
Magma EB7R-x8 Manuale utente
Magma
Magma CB264 Manuale utente
Magma
Magma ExpressBox7 Manuale utente
Magma
Magma CB1F Manuale utente
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
