Magnetic MPB-311 Manuale utente
Operang Instrucons
Full height turnsle with bicycle access
MPB-311
Doc. ID: 58170055EN
Version 00
2
MPB-311
MAGNETIC AUTOCONTROL GMBH
Grienmatt 20
D-79650 Schopfheim
Germany
Phone +49 7622 695 5
Fax +49 7622 695 802
www.magnetic-access.com
Original Operang Instrucons
This document is available as PDF in the Magnec Autocontrol download area
(www.magnec-access.com). Authorisaon is required for download.
3
MPB-311
Contents
Contents
1 Noces on the document 7
1.1 Purpose and contents of this operang instrucons 7
1.2 Reading and storing the operang instrucons 7
1.3 Non-observance of the operang instrucons 8
1.4 Symbols and illustraons used in the operang instrucons 8
1.4.1 Warning notes and noces 8
2 Safety 10
2.1 Intended use 10
2.2 Changes and modicaons 10
2.3 Target groups 11
2.3.1 Operator and its responsibility 11
2.3.2 Personnel – acvies and qualicaons 12
2.4 Personal protecve equipment 13
2.5 Symbols on the device 14
2.6 For your safety 14
2.7 To protect the environment 15
2.8 Emergency opening the pedestrian gate 15
2.9 Earthing support beam, cover and service door 16
3 Technical data 18
3.1 Dimensions and design 18
3.2 Electrical connecon 21
3.3 Operang condions 21
3.4 Emissions 21
3.5 Control unit MGC 22
4 Design and funcon 23
4.1 Design 23
4.2 Funcon 24
4.3 Denions and versions 25
4
MPB-311
Contents
5 Receipt of goods, transport and storage 28
5.1 Receipt of goods 28
5.2 Safety during transport 28
5.3 Transport 30
5.4 Storage 30
6 Unpacking, scope of delivery and idencaon 31
6.1 Unpacking 31
6.2 Scope of delivery 32
6.3 Idencaon 33
6.3.1 Type plate 33
7 Mounng 34
7.1 Safety during mounng 34
7.2 Mounng opons and instrucons, aachment material 35
7.2.1 Overview 35
7.2.2 Oponal base frame FURA-B or FURA-B-D 35
7.2.3 Directly on the foundaon 36
7.3 Required steps 36
7.4 Specifying the mounng posion 37
7.5 Building the foundaon and laying empty conduits 37
7.5.1 Foundaon requirements 37
7.5.2 Empty conduits requirements 38
7.5.3 Building the foundaon and laying empty conduits 38
7.5.4 Foundaon and empty conduit plans 39
7.6 Assembling and mounng the base frame 42
7.6.1 Assembling the base frame FURA-B for
MPB without oponal roof 43
7.6.2 Assembling the base frame FURA-B-D for
MPB with oponal roof 44
7.6.3 Mounng the base frame 45
7.7 Planning and installing inducon loops 46
7.7.1 Ready-assembled and self-assembled inducon loops 46
7.7.2 Inducon loops locaon plan 47
7.7.3 Installing the inducon loops – general notes 48
7.7.4 Installing inducon loops in bitumen, asphalt, or concrete 49
7.7.5 Installing inducon loops under interlocking stone paving 50
7.7.6 Tesng inducon loops 51
5
MPB-311
Contents
7.8 Mounng the pedestrian gate 51
7.8.1 Mounng the base with 2 railings and the cage half with
blocking bracket 52
7.8.2 Mounng the support beam 54
7.8.3 Preparing the mounng of the bicycle door 57
7.8.4 Mounng the oor bearing and the bicycle door 61
7.8.5 Mounng the oor bearing and the centre pillars 68
7.8.6 Mounng the upper barrier of the bicycle access 74
7.8.7 Mounng the guide element 75
7.8.8 Connecng two pedestrian gates 75
7.8.9 Closing the cover of the support beam 76
7.9 Checking the mounng 77
8 Mounng the oponal mounng pillar for access-control devices 78
9 Electrical connecon 86
9.1 Safety during electrical connecon 86
9.2 Installing electrical protecve devices 87
9.3 Opening and closing the cover or service door 88
9.3.1 Opening and closing the cover 88
9.3.2 Opening and closing the service door 90
9.4 Connecng the mains cable 91
9.5 Connecng customer control lines 92
9.6 Connecng emergency opening contacts 93
9.7 Installing and connecng customer access-control devices 93
9.8 Checking the electrical connecons 94
10 Commissioning 95
10.1 Safety during commissioning 95
10.2 Pung the pedestrian gate into operaon 95
10.3 Switching the pedestrian gate on and o 96
10.4 Parameterising the pedestrian gate 97
11 Operaon 97
12 Log book 97
6
MPB-311
Contents
13 Cleaning and maintenance 98
13.1 Safety during cleaning and maintenance 98
13.2 Cleaning the pedestrian gate 99
13.2.1 Cleaning the pedestrian gate from the outside 99
13.2.2 Cleaning the support beam from the inside 100
13.3 Maintenance schedule 100
14 Correcve acon 102
15 Spare parts and repair 103
15.1 Spare parts 103
15.2 Changing and adjusng proximity sensors 103
16 Conversion 105
16.1 Safety during conversion 105
16.2 Converng the locking unit 105
17 Customer service 109
18 Decommissioning 110
18.1 Safety during decommissioning 110
18.2 Taking the pedestrian gate out of service 110
19 Dismounng and disposal 111
19.1 Safety during dismounng and disposal 111
19.2 Dismounng and disposal of the system 111
20 EU-Declaraon of Conformity 112
Index 113
7
MPB-311
Notices on the document
1 Noces on the document
1.1 Purpose and contents of this operang instrucons
These operang instrucons provide all the informaon required for the product in
the various phases of its life cycle.
This operang instrucons contains the following informaon: Design and
funcon, transport and storage, unpacking and delivery, installaon and mounng,
electrical connecon, commissioning, operaon, cleaning and maintenance,
decommissioning, dismounng and disposal.
IMPORTANT!
For the parameterisaon of the MGC control unit and trouble-
shoong, see the separate document "Descripon control unit MGC
(Doc.ID: 58170027)".
1.2 Reading and storing the operang instrucons
Pre-requisite for secure work is compliance with all indicated safety notes, warning
notes and instrucons. In addion, the local accident prevenon regulaons,
general safety regulaons and local environmental regulaons applicable to the area
of applicaon of the product must be observed.
Carefully read these operang instrucons before starng any work! The operang
instrucons are part of the product and must be kept in direct proximity of the
product and well accessible to the personnel at all mes.
When passing the product on to third pares, these operang instrucons must also
be handed over.
8
MPB-311
Notices on the document
1.3 Non-observance of the operang instrucons
Magnec declines all liability for personal injury and property damage caused by not
observing the operang instrucons.
This applies in parcular to damage caused by:
› Improper use
› Use of non-qualied personnel
› Use of non-approved components
› Arbitrary modicaons
› Inappropriate mounng and installaon
› Incorrect operaon
› Inadequate or omied maintenance and repairs
› Use of non-approved spare parts
› Operang a defecve product
1.4 Symbols and illustraons used in the operang instrucons
1.4.1 Warning notes and noces
Warning notes are characterised by pictograms in these instrucons. A warning note
starts with a signal word that expresses the extent of the hazard.
It is absolutely essenal to observe the warning notes and to proceed with cauon
in order to prevent accidents as well as personal injuries and property damage.
Warning notes
DANGER
The signal word WARNING indicates a potenally dangerous situaon,
which can lead to death or severe injuries if not avoided.
WARNING
The signal word WARNING indicates a potenally dangerous situaon,
which can lead to death or severe injuries if not avoided.
9
MPB-311
Notices on the document
CAUTION
The signal word CAUTION indicates a potenally dangerous situaon,
which can lead to minor injuries if not avoided.
NOTICE
The signal word NOTICE indicates a potenally harmful situaon,
which leads to property damage if not avoided.
Notes and recommendaons
IMPORTANT!
The signal word IMPORTANT highlights useful notes and
recommendaons as well as informaon for an ecient and trouble-
free operaon.
10
MPB-311
Safety
2 Safety
2.1 Intended use
The MAGNETIC pedestrian gate MPB is made of a full height turnsle and a bicycle
access. The pedestrian gate MPB is intended only for access control of persons from
a zone not controlled (ZNC) to a zone controlled (ZC). The separate bicycle access
makes it possible to move a bicycle into the zone controlled. Riding the bicycle is
contrary to provisions.
In general, the pedestrian gate is integrated in the fence and gate systems.
The pedestrian gate is intended for passage of persons who can pass the pedestrian
gate safely, quickly and without any help. Separate means of access must be
provided for persons who cannot pass through the pedestrian gate safely, quickly or
without assistance, such as small children, elderly people or people with disabilies.
Children under 14 years of age may only pass through the pedestrian gate under the
supervision of an adult.
The pedestrian gate may only be mounted on non-ammable oors.
The pedestrian gate may only be operated within the temperature range indicated
on the type plate.
Misuse
Any use diering from or beyond this is considered improper use. Magnec is not
liable for any resulng personal injury or damage to property.
For example, the following applicaons are regarded as improper use:
› Use of the pedestrian gate by unaccompanied children under 14 years of age.
› Use of the pedestrian gate by persons who cannot pass the pedestrian gate safely,
quickly or without assistance.
› Use of the pedestrian gate without released passage. This means that the centre
pillar is forced to rotate.
› Mounng of the pedestrian gate on ammable ground.
2.2 Changes and modicaons
Modicaons and conversions to the product, to an aachment or to one of the
components can lead to unforeseen dangers. Magnec's wrien approval must be
obtained before any technical modicaons or alteraons are made to the product
or any of its components.
Indice
Altri manuali Magnetic Tornello
Manuali Tornello popolari di altre marche
OZAK
OZAK VP-125 Manuale
Automatic Systems
Automatic Systems SMARTLANE SL 90X Manuale utente
Alvarado
Alvarado MT Istruzioni per l'installazione e il funzionamento
JKDC SECURITY
JKDC SECURITY JKDC-100C Manuale utente
Alvarado
Alvarado SU5000 Manuale utente
Magnetic Autocontrol
Magnetic Autocontrol MPT 33 Manuale utente
