Makita PC5010C Manuale utente

PC5010C

EN Concrete Planer INSTRUCTION MANUAL 8

PL Szlierka do betonu INSTRUKCJA OBSŁUGI 17

HU Betoncsiszoló HASZNÁLATI KÉZIKÖNYV 28

SK Hobľovačka na betón NÁVOD NA OBSLUHU 38

CS Srovnávací bruska na beton NÁVOD K OBSLUZE 48

UK Шліфувальна машина для

робіт по бетону ІНСТРУКЦІЯ З

ЕКСПЛУАТАЦІЇ 58

RO Mașină de frezat beton MANUAL DE INSTRUCŢIUNI 69

DE Betonschleifer BETRIEBSANLEITUNG 79

Fig.1

Fig.2

Fig.3

Fig.4

Fig.5

Fig.6

Fig.7

Fig.8

Fig.9

Fig.10

Fig.11

Fig.12

Fig.13

Fig.14

Fig.15

Fig.16

Fig.17

Fig.18

Fig.19

Fig.20

Fig.21

Fig.22

Fig.23

Fig.24

Fig.25

Fig.26

Fig.27

Fig.28

Fig.29

Fig.30

Fig.31

Fig.32

Fig.33

Fig.34

Fig.35

Fig.36

Fig.37

Fig.38

8ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: PC5010C

Wheel diameter 125 mm

Max. wheel thickness

(When using as a grinder)

7.2 mm

Spindle thread M14 or 5/8″ (country specic)

Rated speed (n) 9,000 min-1

Overall length 350 mm

Net weight 2.5 - 3.6 kg

Safety class /II

• Due to our continuing program of research and development, the specications herein are subject to change

without notice.

• Specications may differ from country to country.

• Weight according to EPTA-Procedure 01/2014

Intended use

The tool is intended for planing concrete surfaces. With

optional accessories, this tool can be also used for

grinding, sanding and cutting of metal and stone materi-

als without the use of water.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and

can only be operated on single-phase AC supply. They

are double-insulated and can, therefore, also be used

from sockets without earth wire.

Noise

The typical A-weighted noise level determined accord-

ing to EN60745-2-3:

Sound pressure level (LpA) : 85.0 dB(A)

Sound power level (LWA) : 96.0 dB (A)

Uncertainty (K) : 3 dB(A)

WARNING: Wear ear protection.

Vibration

The vibration total value (tri-axial vector sum) deter-

mined according to EN60745-2-3:

Work mode: surface grinding with loop handle

Vibration emission (ah, AG) : 5.5 m/s2

Uncertainty (K) : 1.5 m/s2

Work mode: disc sanding with normal side grip

Vibration emission (ah, DS) : 2.5 m/s2or less

Uncertainty (K) : 1.5 m/s2

NOTE:

The declared vibration emission value has been

measured in accordance with the standard test method

and may be used for comparing one tool with another.

NOTE:

The declared vibration emission value may

also be used in a preliminary assessment of exposure.

WARNING: The vibration emission during actual

use of the power tool can differ from the declared

emission value depending on the ways in which the

tool is used.

WARNING: Be sure to identify safety measures

to protect the operator that are based on an estima-

tion of exposure in the actual conditions of use (taking

account of all parts of the operating cycle such as

the times when the tool is switched off and when it is

running idle in addition to the trigger time).

WARNING: The declared vibration emission

value is used for main applications of the power tool.

However if the power tool is used for other applica-

tions, the vibration emission value may be different.

EC Declaration of Conformity

For European countries only

The EC declaration of conformity is included as Annex A

to this instruction manual.

SAFETY WARNINGS

General power tool safety warnings

WARNING: Read all safety warnings, instruc-

tions, illustrations and specications provided

with this power tool. Failure to follow all instructions

listed below may result in electric shock, re and/or

serious injury.

Save all warnings and instruc-

tions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

9ENGLISH

Concrete planer/grinder safety warnings

Safety Warnings Common for Concrete planing,

Grinding, Sanding, Wire Brushing, or Abrasive

Cutting-Off Operations:

1. This power tool is intended to function as a

concrete planer, grinder, sander, wire brush or

cut-off tool. Read all safety warnings, instruc-

tions, illustrations and specications provided

with this power tool. Failure to follow all instruc-

tions listed below may result in electric shock, re

and/or serious injury.

Operations such as polishing are not recom-

mended to be performed with this power tool.

Operations for which the power tool was not designed

may create a hazard and cause personal injury.

3. Do not use accessories which are not speci-

cally designed and recommended by the tool

manufacturer. Just because the accessory can

be attached to your power tool, it does not assure

safe operation.

4. The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

their rated speed can break and y apart.

5. The outside diameter and the thickness of your

accessory must be within the capacity rating

of your power tool. Incorrectly sized accessories

cannot be adequately guarded or controlled.

Threaded mounting of accessories must match

the grinder spindle thread. For accessories

mounted by anges, the arbour hole of the

accessory must t the locating diameter of the

ange. Accessories that do not match the mounting

hardware of the power tool will run out of balance,

vibrate excessively and may cause loss of control.

Do not use a damaged accessory. Before each

use inspect the accessory such as abrasive

wheels for chips and cracks, backing pad for

cracks, tear or excess wear, wire brush for loose

or cracked wires. If power tool or accessory

is dropped, inspect for damage or install an

undamaged accessory. After inspecting and

installing an accessory, position yourself and

bystanders away from the plane of the rotating

accessory and run the power tool at maximum

no-load speed for one minute. Damaged acces-

sories will normally break apart during this test time.

Wear personal protective equipment. Depending

on application, use face shield, safety goggles

or safety glasses. As appropriate, wear dust

mask, hearing protectors, gloves and workshop

apron capable of stopping small abrasive or

workpiece fragments. The eye protection must

be capable of stopping ying debris generated by

various operations. The dust mask or respirator

must be capable of ltrating particles generated by

your operation. Prolonged exposure to high inten-

sity noise may cause hearing loss.

9. Keep bystanders a safe distance away from

work area. Anyone entering the work area

must wear personal protective equipment.

Fragments of workpiece or of a broken accessory

may y away and cause injury beyond immediate

area of operation.

10.

Hold the power tool by insulated gripping surfaces

only, when performing an operation where the

cutting accessory may contact hidden wiring or its

own cord. Cutting accessory contacting a "live" wire

may make exposed metal parts of the power tool “live”

and could give the operator an electric shock.

11. Position the cord clear of the spinning acces-

sory. If you lose control, the cord may be cut or

snagged and your hand or arm may be pulled into

the spinning accessory.

12. Never lay the power tool down until the acces-

sory has come to a complete stop. The spinning

accessory may grab the surface and pull the

power tool out of your control.

13. Do not run the power tool while carrying it at

your side. Accidental contact with the spinning

accessory could snag your clothing, pulling the

accessory into your body.

14. Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing

and excessive accumulation of powdered metal

may cause electrical hazards.

15. Do not operate the power tool near ammable

materials. Sparks could ignite these materials.

16. Do not use accessories that require liquid

coolants. Using water or other liquid coolants

may result in electrocution or shock.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged

rotating wheel, backing pad, brush or any other acces-

sory. Pinching or snagging causes rapid stalling of the

rotating accessory which in turn causes the uncon-

trolled power tool to be forced in the direction opposite

of the accessory’s rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched

by the workpiece, the edge of the wheel that is entering

into the pinch point can dig into the surface of the material

causing the wheel to climb out or kick out. The wheel may

either jump toward or away from the operator, depending on

direction of the wheel’s movement at the point of pinching.

Abrasive wheels may also break under these conditions.

Kickback is the result of power tool misuse and/or

incorrect operating procedures or conditions and can be

avoided by taking proper precautions as given below.

1. Maintain a rm grip on the power tool and

position your body and arm to allow you to

resist kickback forces. Always use auxiliary

handle, if provided, for maximum control over

kickback or torque reaction during start-up.

The operator can control torque reactions or kick-

back forces, if proper precautions are taken.

2. Never place your hand near the rotating acces-

sory. Accessory may kickback over your hand.

3. Do not position your body in the area where

power tool will move if kickback occurs.

Kickback will propel the tool in direction opposite

to the wheel’s movement at the point of snagging.

4. Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing

have a tendency to snag the rotating accessory

and cause loss of control or kickback.

5. Do not attach a saw chain woodcarving blade

or toothed saw blade. Such blades create fre-

quent kickback and loss of control.

10 ENGLISH

Safety Warnings Specic for Grinding and Abrasive

Cutting-Off Operations:

1. Use only wheel types that are recommended

for your power tool and the specic guard

designed for the selected wheel. Wheels for

which the power tool was not designed cannot be

adequately guarded and are unsafe.

2. The grinding surface of centre depressed

wheels must be mounted below the plane of

the guard lip. An improperly mounted wheel that

projects through the plane of the guard lip cannot

be adequately protected.

The guard must be securely attached to the

power tool and positioned for maximum safety,

so the least amount of wheel is exposed towards

the operator. The guard helps to protect the operator

from broken wheel fragments, accidental contact with

wheel and sparks that could ignite clothing.

Wheels must be used only for recommended

applications. For example: do not grind with the

side of cut-off wheel. Abrasive cut-off wheels are

intended for peripheral grinding, side forces applied

to these wheels may cause them to shatter.

5. Always use undamaged wheel anges that are

of correct size and shape for your selected

wheel. Proper wheel anges support the wheel

thus reducing the possibility of wheel breakage.

Flanges for cut-off wheels may be different from

grinding wheel anges.

6. Do not use worn down wheels from larger

power tools. Wheel intended for larger power tool

is not suitable for the higher speed of a smaller

tool and may burst.

Additional Safety Warnings Specic for Abrasive

Cutting-Off Operations:

1. Do not “jam“ the cut-off wheel or apply exces-

sive pressure. Do not attempt to make an

excessive depth of cut. Overstressing the wheel

increases the loading and susceptibility to twisting

or binding of the wheel in the cut and the possibil-

ity of kickback or wheel breakage.

2. Do not position your body in line with and

behind the rotating wheel. When the wheel, at

the point of operation, is moving away from your

body, the possible kickback may propel the spin-

ning wheel and the power tool directly at you.

3. When wheel is binding or when interrupting

a cut for any reason, switch off the power

tool and hold the power tool motionless until

the wheel comes to a complete stop. Never

attempt to remove the cut-off wheel from the

cut while the wheel is in motion otherwise

kickback may occur. Investigate and take correc-

tive action to eliminate the cause of wheel binding.

4. Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and

carefully re-enter the cut. The wheel may bind,

walk up or kickback if the power tool is restarted in

the workpiece.

5. Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kick-

back. Large workpieces tend to sag under their

own weight. Supports must be placed under the

workpiece near the line of cut and near the edge

of the workpiece on both sides of the wheel.

6. Use extra caution when making a “pocket cut”

into existing walls or other blind areas. The

protruding wheel may cut gas or water pipes, elec-

trical wiring or objects that can cause kickback.

Safety Warnings Specic for Sanding Operations:

1. Do not use excessively oversized sanding

disc paper. Follow manufacturers recommen-

dations, when selecting sanding paper. Larger

sanding paper extending beyond the sanding

pad presents a laceration hazard and may cause

snagging, tearing of the disc or kickback.

Safety Warnings Specic for Wire Brushing

Operations:

1. Be aware that wire bristles are thrown by the

brush even during ordinary operation. Do not

overstress the wires by applying excessive

load to the brush. The wire bristles can easily

penetrate light clothing and/or skin.

2. If the use of a guard is recommended for wire

brushing, do not allow any interference of the

wire wheel or brush with the guard. Wire wheel

or brush may expand in diameter due to work load

and centrifugal forces.

Additional Safety Warnings:

1. Always install the dust collecting wheel guard

before operation as a concrete planer.

2. When using depressed centre grinding wheels,

be sure to use only berglass-reinforced

wheels.

3. NEVER USE Stone Cup type wheels when

using as a grinder. This tool is not designed for

these types of wheels and the use of such a prod-

uct may result in serious personal injury.

4. Be careful not to damage the spindle, the

ange (especially the installing surface) or the

lock nut. Damage to these parts could result in

wheel breakage.

5. Make sure the wheel is not contacting the

workpiece before the switch is turned on.

6. Before using the tool on an actual workpiece,

let it run for a while. Watch for vibration or

wobbling that could indicate poor installation

or a poorly balanced wheel.

7. Use the specied surface of the wheel to per-

form the grinding.

8. Do not leave the tool running. Operate the tool

only when hand-held.

9. Do not touch the abrasive wheel and the work-

piece immediately after operation; it may be

extremely hot and could burn your skin.

10. Observe the instructions of the manufacturer

for correct mounting and use of wheels.

Handle and store wheels with care.

11. Do not use separate reducing bushings or

adaptors to adapt large hole abrasive wheels.

12. Use only anges specied for this tool.

13. For tools intended to be tted with threaded

hole wheel, ensure that the thread in the wheel

is long enough to accept the spindle length.

14. Check that the workpiece is properly

supported.

15. Pay attention that the wheel continues to

rotate after the tool is switched off.

Altri manuali per PC5010C

Indice

Lingue:

Altri manuali Makita Pialla

Manuali Pialla popolari di altre marche

Felisatti

Felisatti PF180/1500 Manuale utente

DeWalt

DeWalt DW 1150 Guida

Triton

Triton TRP UL Guida rapida

Melbourne

Melbourne MTC-49407 Manuale utente

VARO

VARO POWERplus POW1520 Manuale utente

Powermatic

Powermatic 209 Manuale di servizio

Skil

Skil 1565 Manuale utente

Scheppach

Scheppach Plana 3.0 Istruzioni per il montaggio

Grizzly

Grizzly G1033X Manuale utente

Stanley

Stanley STPP7502 Manuale utente

Palmgren

Palmgren 84115 Manuale utente

Draper

Draper PT610V Manuale utente

Berner

Berner BP 40-82 C Manuale utente

Grizzly

Grizzly G0603X Manuale utente

King Industrial

King Industrial CT-381FX Manuale utente

FXA

FXA FXAJD8220 Manuale utente

Delta Rockwell

Delta Rockwell 22-101 Manuale utente

Oliver

Oliver 4420 Manuale utente