Malaguti CIAK MASTER 50-4T Guida utente
CIAK MASTER 50-4T
B
ELECTRIC SYSTEM
TROUBLESHOOTING
WORKSHOP MANUALS
B
10.05 3
Table of contenents
CHAPTER
PAGEISSUE
ELECTRIC SYSTEM TROUBLESHOOTING
ENGLISH
SECTION 1
B- TROUBLESHOOTING
Table of contents
Sect. Page
INTRODUCTION 1 5
Manual updates 1 5
Notes for easy consultation 1 6
Page layout 1 6
Modified pages 1 6
Additional pages 1 6
Editing symbols 1 6
Abbreviations 1 8
TROUBLESHOOTING 2 9
Electrical components 2 9
General wiring diagram 2 11
Checking switches 2 12
Checking procedures 2 12
Connection of the switches described in this manual 2 12
Checking fuses 2 13
Position of switches and connection of connectors 2 14
Troubleshooting 2 15
Checking light system 2 24
Troubleshooting 2 28
B
10.05 5
Introduction
CHAPTER
PAGEISSUE
ELECTRIC SYSTEM TROUBLESHOOTING
ENGLISH
SECTION 1
B- TROUBLESHOOTING
• Malaguti S.p.a. reserves the right to make any and all changes to its vehicles as it deems fit and appropriate
at any time without prior notice.
•No part of this publication, whether text or illustrations, may be reproduced or circulated. Malaguti
reserves all rights over this publication. Reasons must be given for any request for permission (written) thereto.
INTRODUCTION
•This publication describes all necessary steps for troubleshooting concerning the electrical system and of
the possible service operations, which are necessary for their solution. It supplies the trade technicians
(authorised customer service centres) with the necessary information for operating in compliance with the
modern concepts of “good practice” and “safety at work”.
• Additional information is available in the Engine Service Manual and Spare Parts Catalogue.
• All described operations must be performed by technicians with the necessary skill and experience.
• The steps for removal of body parts and of electric and mechanical components, to allow access to wiring or
electric components to service, can be taken from the “Chassis” Workshop Manual.
• We recommend you follow the information given in this publication with care.
• For any further information you may need, refer to the Malaguti S.p.A. Technical Department.
• It is essential to follow the instructions with great care. Work carried out carelessly or, worse still, work that has
not been accomplished, can cause injuries and damage or, in the less serious cases, tiresome complaints.
MANUAL UPDATES
•Any subsequent updates applying to this Manual will be sent in a reasonable time.
•The table of contents will be duly updated in the event that new pages are inserted, which render the consultation
of the manual difficult.
• IMPORTANT! The “Electrical System Troubleshooting Manual” is to be considered as an essential tool to
be properly kept up-to-date so as to maintain its
“validity”
over time.
FIRST EDITION: 10/05
B
610.05
Introduction
CHAPTER
PAGE ISSUE
ELECTRIC SYSTEM TROUBLESHOOTING
ENGLISH
SECTION 1
B- TROUBLESHOOTING
W
Z
Y
X
MODIFIED PAGES
• Modified pages shall bear the same number as those in the previous edition/pre-modified ones, followed by the
letter M, with the date of issue appearing in the appropriate box.
• Modified pages may contain new illustrations; in this case, the added illustration (or illustrations) will bear the
number of the illustration on the former page, followed by a letter.
ADDITIONAL PAGES
• Any additional pages shall bear the last number of the section to which they belong, followed by the letter A
and the date of issue.
EDITING SYMBOLS
• Symbols have been provided for quick and easy reference (see page 7). They identify situations requiring
utmost attention, practical advice or simple information.
•These symbols may appear next to a text (in which case they refer solely to the text itself), next to a figure
(in which case they refer to the topic illustrated in the figure and to the relative text), or at the top of the page
(in which case they refer to all the topics dealt with in the page).
Note:
the meaning of the symbols should be duly memorised as their scope is to avoid having to repeat basic technical
concepts or safety recommendations. They are therefore to be considered as veritable “memory tags”. In case
of any doubt as to their meaning, consult the page in which they are fully described.
(RH PAGE)
PAGE LAYOUT
NOTES FOR EASY CONSULTATION
YChapter
XSection title
WPage N°
ZDate of issue
B
10.05 7
Introduction
CHAPTER
PAGEISSUE
ELECTRIC SYSTEM TROUBLESHOOTING
ENGLISH
SECTION 1
B- TROUBLESHOOTING
R
M
L
H
F
A
B
D
C
I
G
E
A) CAUTION! Recommendations and precautions regarding
rider safety and vehicle integrity.
B) WARNING! Situations entailing the risk of personal injury
to maintenance or repair mechanics, other workshop
personnel or third parties, or damage to environment,
vehicle or equipment.
C) FIRE HAZARD
Indicates operations which may constitute a fire hazard.
D) RISK OF EXPLOSION Indicates operations which may
constitute a risk of explosion.
E) TOXIC FUMES
Indicates a possibility of intoxication or inflammation of
the upper respiratory tract.
F) MECHANICAL MAINTENANCE Operations to be
performed only by an expert mechanic.
G) ELECTRICAL MAINTENANCE
Operations be performed only by an expert electrical/
electronic technician
H) NO! Operations to be absolutely avoided
I) ENGINE SERVICE MANUAL Indicates information which
may be obtained by referring to said manual.
L) SPARE PARTS CATALOGUE
Indicates information which may be obtained by referring
to said catalogue
B
810.05
Introduction
CHAPTER
PAGE ISSUE
ELECTRIC SYSTEM TROUBLESHOOTING
ENGLISH
SECTION 1
B- TROUBLESHOOTING
A
Note:
the letter V in the illustrations refers to retaining or adjusting screws. The number following this letter refers to
the number of the same type of screw in the unit or component described and illustrated. Letters not followed
by a number indicate a single screw. In case of different screws being referred to in the illustration, the letter
Vis followed by a number and a small letter, for instance: (V4a).
Unless otherwise specified, units and components are reassembled by proceeding in the reverse order of
removal.
Before any servicing, make sure that the vehicle is perfectly stable.
The front wheel should preferably be anchored to the equipment integral with the lifting board.
ABBREVIATIONS
FFigure
Cs Tightening torque
PPage
Pr Paragraph
SSection
Sc Diagram
TTable
VScrew
B
10.05 9
CHAPTER
PAGEISSUE
ELECTRIC SYSTEM TROUBLESHOOTING
ENGLISH
SECTION 2
Electrical components
SECTION 2
B- TROUBLESHOOTING
ELECTRICAL COMPONENTS
1) HORN
2) SWITCH WITH KEY
3) STARTING RELAY
4) FUEL PROBE
5) HV COIL
6) BATTERY
7) C.D.I. CONTROL UNIT
8) VOLTAGE REGULATOR
9) RESISTANCE
B
10 10.05
CHAPTER
PAGE ISSUE
ELECTRIC SYSTEM TROUBLESHOOTING
ENGLISH
SECTION 2
General wiring diagram
SECTION 2
B- TROUBLESHOOTING
1
2
3
4
6
5
7
8
9
10
11
12
13
14
15
16
17
18
13
19
20 21 22
B
10.05 11
CHAPTER
PAGEISSUE
ELECTRIC SYSTEM TROUBLESHOOTING
ENGLISH
SECTION 2
General wiring diagram
SECTION 2
B- TROUBLESHOOTING
GENERAL WIRING DIAGRAM
COLOUR KEY
N-R BLACK/RED B-R WHITE/RED
R RED BL BLUE
RS PINK BL-R BLUE/RED
VL PURPLE GL YELLOW
VL-N PURPLE/BLACK GL-N YELLOW/BLACK
VR GREEN GL-V YELLOW/GREEN
AR-BL ORANGE/BLUE GL-R YELLOW/RED
AZ LIGHT BLUE GR GREY
AZ-B LIGHT BLUE/WHITE M BROWN
B WHITE M-B BROWN/WHITE
B-N WHITE/BLACK N BLACK
KEY TO THE GENERAL WIRING DIAGRAM
1) 12V BATTERY
2) RELAY
3) STARTER MOTOR
4) REAR LEFT TURN INDICATOR
5) REAR OPTICAL UNIT
6) REAR RIGHT TURN INDICATOR
7) FUEL LEVEL SENSOR
8) VOLTAGE REGULATOR
9) ELECTRICAL STARTER
10) CHASSIS GROUNDING
11) RESISTANCE
12) FRONT RIGHT TURN INDICATOR
13) STOP LIGHT
14) RIGHT HAND SWITCH BLOCK
15) SWITCH WITH KEY
16) INSTRUMENT BOARD
17) HEADLIGHT
18) LEFT HAND SWITCH BLOCK
19) FRONT LEFT TURN INDICATOR
20) HORN
21) FLY WHEEL MAGNETO
22) ELECTRONIC CONTROL UNIT
B
12 10.05
CHAPTER
PAGE ISSUE
ELECTRIC SYSTEM TROUBLESHOOTING
ENGLISH
SECTION 2
Checking switches
SECTION 2
B- TROUBLESHOOTING
CHECKING SWITCHES
CHECKING PROCEDURES
Using a tester (Code n°08609500), check the switches
by making sure that there is continuity between terminals
and that they are correctly connected.
Replace the switch, even if only one of the possible
combinations does not give the requested result.
NOTE: flick the switch from “ON” to “OFF” several
times and select ::
::
:.
Set the tester to its correct “0” position,
before connecting the switches.
CONNECTION OF THE SWITCHES DESCRIBED IN THIS MANUAL
- This manual contains connection diagrams, like the one illustrated hereby,
which illustrate how switch terminals should be connected (key switch, brake
switch, start button, etc.).
- The first column from the left indicates the different positions of the switch
and the top line the colour of the wires connected to the switch terminals.
- The “ ” symbol identifies terminals in which there is a condition of continuity,
i.e. a closed circuit, in a certain position of the switch.
- In this diagram:
“B/R” and “N” feature continuity with the button pressed (switch in its “ON”
position).
Indice
Altri manuali Malaguti Motociclo
Malaguti
Malaguti X3Motard Manuale di istruzioni
Malaguti
Malaguti MADISON 300 2018 Manuale utente
Malaguti
Malaguti Password 250 Manuale di istruzioni
Malaguti
Malaguti centro 125 ie Manuale utente
Malaguti
Malaguti Dune X 125 Guida
Malaguti
Malaguti MADISON 3 125 cc Manuale di istruzioni
Malaguti
Malaguti Blog 126 Manuale utente
Malaguti
Malaguti XAM CE Manuale utente
Malaguti
Malaguti CNK 50 DRAKON Manuale di istruzioni
Malaguti
Malaguti F12R L.C. 50 cc Manuale di istruzioni
Malaguti
Malaguti MONTE 125 Manuale utente
Malaguti
Malaguti MADISON 125 Manuale utente
Malaguti
Malaguti Drakon 50 Manuale utente
Malaguti
Malaguti RST125 2018 Manuale utente
Malaguti
Malaguti PHANTOM F12 Manuale utente
Malaguti
Malaguti GRIZZLY Manuale utente
Malaguti
Malaguti XTM POWER UP 2007 Manuale utente
Malaguti
Malaguti Grizzly Minicross RCX/12 50CC Manuale utente
Malaguti
Malaguti XTM 50 Manuale di istruzioni
Malaguti
Malaguti CNK 50 DRAKON Manuale di istruzioni
