Malem Universal MO15 Manuale utente

Malem© Universal©

Wireless Alarm Model MO15

Instructions for use

The alarm can be used for several applications

or combinations:

lWander alarm lContinence alarm

lSit up alarm lEnuresis alarm

lSleepwalking alarm lDialysis leakage alarm

Up to seven clients can be monitored with one receiver

Ideal for nursing/care homes, special schools, hospitals,

institutions and individuals

Helps to prevent bed sores and broken bones in

Dementia, Alzheimer’s, Memory Loss, the Elderly,

People with Special Needs

IMPORTANT

Please read instruction booklet

before use

6492 Master IBooklet 061010_Master IBooklet 061010 21/01/2011 14:45 Page 1

Disclaimer

Malem© Universal©Wireless Alarm is designed

as a helpful and versatile aid. It is not intended

to replace human care or supervision and

the manufacturer, Malem Medical,

is not responsible for any consequences

resulting from the use,

misuse or failure of this device.

6492 Master IBooklet 061010_Master IBooklet 061010 21/01/2011 14:45 Page 2

Contents

Instructions for Use

Easy-Clip©Sensor........................................................................2

Standard Sensor ..........................................................................3

Bed-Mat ......................................................................................4

Wander-Mat ..................................................................................6

Dialysis-Mat ................................................................................7

Resetting Receiver (Rx) Sound ....................................................7

Channel Selection ........................................................................8

Receiver LED Number Selection..................................................8

Re-tuning (Pairing)........................................................................8

Sound Selection Switch ..............................................................8

Batteries ......................................................................................9

Guarantee ....................................................................................9

Repairs ........................................................................................9

Cleaning........................................................................................10

Disposal........................................................................................10

Fault Finding ................................................................................10

Specification Tx & Rx ..................................................................11-12

Diagrams Tx & Rx ........................................................................13-16

How to Connect Tx with Different Sensors..................................17-19

The Inverter ..................................................................................20-21

MM100111

6492 Master IBooklet 061010_Master IBooklet 061010 21/01/2011 14:45 Page 3

Instructions for use

1. Switch on the receiver (Rx) unit. Green LED

will flash once every two seconds. See page 15.

2. Remove insulator from battery compartment

(if present) of the transmitter (Tx) unit. See page 14.

3. Plug the sensor of choice into the transmitter

(Tx) unit. See pages 17 & 18.

4. If used with Easy-Clip©Sensor (EC):

i) Make sure the Easy-Clip©Sensor lever is in the up position.

(Lowering the lever without placing material between the front jaws

will activate the transmitter and trigger the receiver buzzer). If buzzer

does not sound, retune Tx & Rx as per instructions. See page 8.

ii) Using the safety pin, attach the Tx to the pyjama top or nightdress

close to the shoulder. Attach Tx to material before wearing garment

if preferable. Carefully lock the safety pin. Do not use safety pin if

faulty. Optional shoulder clip is available for clinics on request if

safety pin use is unsuitable.

iii) Thread sensor lead inside top as shown in diagram above.

For small children, loop and tie sensor lead to shorten length.

iv) Attach sensor clip to the outside of close fitting underwear (at the

location where it is most likely to get wet first), by inserting the

folded underpants material inside the front jaw of the clip then

lowering the lever. (Lowering the lever without any dry material in the

jaws will activate the Tx, trigger the Rx alarm and prevent the Rx

from being reset). Lift the lever and press the reset button. Do not

reset the Rx by switching off. Always use the reset button.

MALEM

UNIVERSAL

WIRELESS ALARM

TRANSMITTER

MO15(Tx)

Lock the Easy-Clip

onto the material by

pressing down the lever

IMPORTANT:

Regularly CLEAN Easy-Clip

Sensor in soapy water, rinse

and shake dry

IMPORTANT: DO NOT PLACE

ANY MATERIAL UNDER THE

SECURING LEVER

Place underwear material into mouth

(jaws) at the front of the Easy-Clip

6492 Master IBooklet 061010_Master IBooklet 061010 21/01/2011 14:45 Page 4

5. If used with Standard Sensor (BT):

a) Absorbent pad:

i) Cut off one end of an

absorbent pad such as sanitary

or incontinence pad and insert

the sensor in between the

layers.

ii) Anchor with crocodile clip

to prevent sensor from

being pulled out. Uncover

the backing strip and stick

the pad inside a pair of close fitting

pants, ensuring the sensor is located

where it will come into contact with the

flow of urine.

b) Between two pairs of underpants:

i) Sandwich between two pairs of cotton briefs (not boxer shorts).

Anchor with crocodile clip.

c) Within Y-front fold:

i) Place sensor plate within Y-fronts fold and anchor by locating the

crocodile clip on the outside of the waistband of the pants. Avoid

nylon/polyester underwear.

d) With pull-ups or nappies:

i) Cut a small slit into the outside of the material and insert the sensor

plate at a location close to the urine flow.

Please note that sensor and clip

are gold plated

Please make sure the sensor plate and

the crocodile clip are attached between

the two pairs of pants and MUST NOT

come in contact with the skin

Outer Pants

Inner Pant

6492 Master IBooklet 061010_Master IBooklet 061010 21/01/2011 14:45 Page 5

6. If used with Bed-Mat Sensor (BM):

a) Under no circumstances should the transmitter (Tx) be

attached to the users’ clothing when using a Bed-Mat.

b) Place a clean and dry Bed-Mat correct side up over the mattress

in the area which is normally wetted and gently tie down. See page 5.

c) Cover the Bed-Mat with a Clean Dry Cotton sheet and/or

Bath Towel and make the bed up as usual. Avoid

nylon/polyester sheets as they can cause ‘false’ alarms due to

increased perspiration. Adjust cover thickness over the mat to

suit.

d) Do not place plastic sheets directly under the Bed-Mat as

condensation will cause the alarm to trigger. (See diagram page 5)

e) Attach the Bed-Mat wire to the Tx and place the Tx beside the

bed. See page 17.

f) Please tuck in the Bed-Mat wire so that it is not in the way for

getting in and out of bed.

g) Upon waking to the Rx, try to stop any more urine from

being released and use the lavatory to completely empty the

bladder.

h) The Rx alarm sound can be stopped ONLY when the Bed-Mat

wire is unlocked from the Tx and the reset button on the Rx

is pressed.

i) For reuse, the Bed-Mat must be wiped clean with detergent and dried

then replaced in a freshly made bed, as before.

j) To test the system, place a damp cloth across the foil tracks on

the Bed-Mat.

6492 Master IBooklet 061010_Master IBooklet 061010 21/01/2011 14:45 Page 6

If using a plastic

protective mattress

sheet place adhesive

tape over the Bed-Mat

lower contacts.

Use a BATH TOWEL to

cover the Bed-Mat and

cotton sheet. Adjust towel

thickness to suit. Pillow

Transmitter (Tx)

Bedside

table

Tuck wire from Bed-Mat to

alarm away neatly to prevent

tripping or entanglement.

Tie Bed-Mat

around mattress.

Place cotton

sheet over

Bed-Mat.

MALEM

UNIVERSAL

WIRELESS ALARM

TRANSMITTER

MO15(Tx)

Under NO

circumstances should

the transmitter (Tx) be

attached to the users’

clothing when using a

Bed-Mat.

Holes for tying Bed-Mat to the mattress.

Mattress

Bed-Mat

Sheet

Bath Towel

6492 Master IBooklet 061010_Master IBooklet 061010 21/01/2011 14:45 Page 7

Hints regarding the use of Bed-Mat:

lPress the reset button once, receiver alarm sound will stop. LED will continue

to flash. If the Bed-Mat is not dried or disconnected, the alarm sound will start

again within two minutes.

lPress and hold the reset button for two seconds to stop the alarm and turn off

the LED.

lThe Bed-Mat positively locks to the Tx to prevent accidental disconnection.

However, it must be unlocked before attempting to reset the alarm.

lPlease use a thicker cotton sheet or place a bath towel above

the Bed-Mat if sweating is triggering the Tx prematurely. Avoid plastic and

man-made fibres as they may cause static discharge and false alarm.

lTreat the Bed-Mat with care. Avoid folding it or jumping on it.

lPlease replace the Bed-Mat with a new one if it has deteriorated and use a

new one with each user. (National Guidelines)

lPlease note that sleeping directly on an uncovered Bed-Mat or touching it by

hand may trigger the Tx and sound the alarm.

lDo not place plastic sheets directly under the Bed-Mat as condensation may

trigger the alarm.

7. If used with Wander-Mat Sensor (WM):

a) Activation by applied pressure: place the Wander-Mat (WM) in the

appropriate position depending on the way you wish to use it. The

Wander-Mat can be placed beside the bed or near the door so that

treading on the Mat will activate the Tx. Please place a door mat over

the Wander-Mat so as not to trip over the Wander-Mat. Plug into the

Tx and place away safely. See page 19.

b) Activation by removal of pressure: place the Wander-Mat (WM) over

the mattress but under the sheet, in a position so that the user is laying

over it or place on a chair so that the user is sitting on it. Plug the

Wander-Mat wire into the ‘inverter’ then plug the inverter wire into the

Tx and place Tx away safely. If the user gets out of bed or out of the

chair, the Tx will be activated triggering the Rx sound and selected LED.

c) Once the receiver (Rx) is triggered, the appropriate red LED will be

flashing. The buzzer sound can be silenced by pressing the reset button

on the top of the Rx. (Do not use the on/off switch to reset the Rx as

this will damage the microprocessor). The activated LED will remain

flashing. If the matched Tx remains active, the Rx will sound again after

two minutes. Press and hold for 3 seconds to deactivate and switch

LED off.

6492 Master IBooklet 061010_Master IBooklet 061010 21/01/2011 14:45 Page 8

8. If used with Dialysis-Mat Sensor (DM):

a) Select the correct side of the Mat with shiny tracks up.

b) Place the Mat over the chair arm.

c) Plug the Mat wire into the Transmitter, tuck the wire and place Tx out

of the way in a safe place. See page 18.

d) Test the Mat by placing a slightly wet tissue over the tracks. The Rx

should sound.

e) If sweating is likely to activate Tx and sound the alarm cover the Mat

surface with tissue paper. Adjust thickness to suit.

f) Rest patients arm over the Mat.

g) Wipe Mat clean and dry before use again.

9. Deactivating the Transmitter:

a) If using the Easy-Clip©sensor, lift the sensor lever and remove from

underpants (wash Easy-Clip©sensor frequently).

b) If using the Standard sensor, unclip the crocodile clip and remove the

sensor, wipe sensor plate dry and clean regularly.

c) If using the Bed-Mat, unplug the Bed-Mat from the Tx, remove the

sheet, wipe clean and dry thoroughly before repositioning.

d) If using the pressure/release Wander-Mat, unplug from the Tx and

reposition the user on the Mat.

c) If using the Dialysis-Mat, unplug from the Tx, clean and dry the Mat

then, reposition.

f) Press the reset button on the Rx to silence the buzzer.

10. Resetting the Rx Sound:

a) Press and hold the reset button for 2 seconds to switch off the

sound and de-activated LED/s (make sure matched Tx is not active).

b) The matched Tx/Rx will not trigger the Rx if the Tx is activated within

2 minutes of previous activation.

c) For easy identification, an adhesive label can be used on the front of

the Rx where you can write the room number or occupant name for

each of the seven LEDs.

6492 Master IBooklet 061010_Master IBooklet 061010 21/01/2011 14:45 Page 9

Channel Selection see diagram on page 14

can be paired with up to seven transmitters. To avoid interference

from the 7 transmitters or other wireless equipment, you need to

select different channel settings for each of the transmitters. A choice of 64

settings is possible and should be changed in case of interference.

To change the channel setting, remove the back of the transmitter using a slotted

screwdriver. Lower to open. Change the setting of the code selection switch (the

one on the left) by moving any of the switches in any of the 64 combinations.

Receiver LED Number Selection see diagram on page 14

To match a Tx with a specific Rx LED number, remove the battery cover of the

Tx using a slotted screwdriver. The LED selection switch is the one on the right.

Select the LED number by sliding the matching number (between 1 and 7) of the

sliding switch to ON. Re-tune Tx and Rx. See below.

Re-tuning the Rx and Tx see diagram on page 14 & 16

All additional transmitters will need to be re-tuned with the Rx.

a) Select the desired Rx LED number first (see above).

b) Push and release the straight end of a paper clip into the small

LEFT hole at the back of the receiver. All the 7 LED’s will glow.

c) Immediately and while the LED’s are glowing, activate the Tx you wish to

standard sensor or Bed-Mat or applying pressure on the Wander-Mat or

wetting the Dialysis-Mat.

d) The LED’s will switch off apart from the selected one which will glow on

and off. The next activation of the Tx will activate the Rx LED and the buzzer.

e) Repeat for all other additional transmitters.

f) Remember to change channel if you are experiencing any interference

from other transmitters or wireless equipment.

You can also tune several receivers to the same transmitters. This is helpful if

more than one carer wants to monitor the transmitters.

Sound Selection Switch see diagram on page 16

The receiver is factory set to 8 random sounds.

For single sound selection:

a) Open the Rx battery cover using a slotted screwdriver. Insert blade into

slot and twist.

b) Slide to ‘ON’ any one of the switches between 1 and 8.

c) Slide all other switches apart from 10 to the ‘OFF’ position.

d) Do not slide switch 10 to ‘OFF’ as this will silence the Rx sound.

1 2 3 4 5 6

OFF

1 2 3 4 5 6 7 8

OFF

6492 Master IBooklet 061010_Master IBooklet 061010 21/01/2011 14:45 Page 10

Indice

Altri manuali Malem Sistema di sicurezza

Malem

Malem MO12 Manuale utente

Malem

Malem MO4S Manuale utente

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente