Manson Engineering Industrial SPS-9600 Manuale utente

SPS-9600/9602

High Current Switching Mode Power Supply with Remote Sensing & Control

User Manual

1. INTRODUCTION

This 900W switching mode DC regulated dual output power supply series provides high current with

constant current limiting protection. It has a variable output: 1~ 15Vdc for SPS-9600 & 1~30Vdc for

SPS-9602. It is designed with a high efficient Active Power Factor Corrector. The remote sensing terminal is

used to compensate for long output line losses.The output voltage level can be externally controlled via the

remote control terminal.

2. PRECAUTIONS

●Never Short the Remote Sensing Terminal

●This power supply is for Indoor Use Only.

●Do not expose the power supply to sun, high humid and dusty environment.

●Never remove the metal cover of the power supply while AC power is connected.

●Never touch the unit when your hands are wet.

●Never block the ventilation slots and cooling fan air intake window

●Never attempt to repair the power supply. Incorrect re-assembly may result in a risk of electric shock or

fire.

●Never use the power supply for the load requiring higher current than the designed value otherwise it

may damage the power supply.

●Place the power supply on a flat surface with sufficient clearance, dry, dust free surroundings for

ventilation.

3. CONTROLS AND INDICATORS

(1) Voltage & Ammeter LED Display

(2) Overload LED Indicator – Overload(Constant Current Limiting) & Short-Circuit Protection

(3) Output Voltage Control Knob(control both main and auxilary output)

(4) Power ON/OFF Switch

(5) Power ON/OFF LED

(6) Auxiliary Output Terminal (Rated 5A for SPS-9600 / Rated 3A for SPS-9602)

(7) Main Output Terminal (Rated 60A for SPS-9600 / Rated 30A for SPS-9602)

Note : SPS-9600 : The Total Rated Current(Aux. + Main) is 60A

SPS-9602 : The Total Rated Current(Aux. + Main) is 30A

(8) Remote Sensing Terminal (Warning! : Never short the remote sensing terminal)

(9) Remote Control Terminal

(10) Remote Control ON/OFF Switch

(11) Cooling Fan Air Intake Grille

(12) AC Input Plug

Front Rear

Note: Main and Auxiliary output give out same output voltage

CAUTION! : The AC Input is DOUBLE POLE FUSING

4. CONNECTION

4.1 This series has 2 models. Make sure you have purchased the correct one.

They have different output voltage range and current as following:

Model Number Output Voltage Range Total Rated Current (Main+Auxiliary)

SPS - 9600 1 ~ 15V 60A

SPS - 9602 1 ~ 30V 30A

4.2 Check the rating label of the power supply and make sure it complies with your AC mains voltage.

Connect the power supply to the AC Mains using the provided power cord.

Steps 4.3 & 4.4 explain how to use the special features: remote sensing and remote control.

You can use the 2 features at the same time or separately.

Please go to step 4.5 if you do not use the 2 features and make sure the remote control

ON/OFF switch is in OFF position(rear panel).

4.3 REMOTE SENSING – Take note of the warning and follow the order of installation.

Warning!:Never short the Remote Sensing Terminal

Connection:

1. First complete the power connections between power supply and equipment.

2. Check and make sure the power connections are secure.

3. Then make connections between Remote Sensing and equipment.

Warning!:Never short the Remote Sensing Terminal

Dis-connection:

1. First disconnect the remote sensing connections.

2. Then disconnect the power connections between the power supply and equipment.

Fig 3 showing connections between Remote Sensing, Power output and Equipment.

The remote sensing wire should be AT LEAST 22AWG wire size.

4.4 REMOTE CONTROL

4.4.1 VOLTAGE REMOTE CONTROL

Set up the provided remote connector plug

(a) Remove the black portion of the remote control connector plug by removing the screw as Fig 4.

Black portion

Silver portion Fig. 4

2. Rotate the black portion1. Remove the screw

(b) Solder 3 wires(22AWG) to PORT 1, 2 & 3 of black portion as shown in Fig.5.

(d) Plug the remote connector plug into the remote control terminal of the power supply.

(e) Secure the remote connector plug to the terminal socket by locking connector ring(Fig 6).

Then, you can choose either method A or B below to use the remote control feature:

Method A : Using External Voltage Source

A variable external voltage source of 0 ~ 5V is fed into the remote control terminal to

adjust the output voltage level of both Main and Auxiliary output.

Warning! : Do not input higher than 5V, otherwise the OverVoltage Protection(OVP) will be

triggered.

A(i) Make sure the load is disconnected and the power supply is OFF.

(ii) Use ONLY wires from port 2 and 3. Then, connect port 2 to positive polarity of the external

voltage source and port 3 to negative polarity of the external voltage source.

(iii) Turn the Remote Control ON/OFF Switch to ON position.

(iv) Switch on the power supply.

(v) Vary the external input voltage 0 – 5V to check and verify for the full output voltage range of

power supply.

(vi) Switch off the power supply.

Method B: Using Internal Voltage Source

B (i) Make sure the load is disconnected and the power supply is OFF.

(ii) Prepare a 5kohm variable resistor and use wires from port 1, 2 and 3 as shown in Fig.7.

(iii) Turn the the Remote Control ON/OFF Switch to ON position.

(iv) Switch on the power supply.

(v) Adjust the 5kohm variable resistor from one end to other end to check and verify for the full

output voltage range of power supply.

(vi) Switch off the power supply.

Outer ring

Fig. 6

Fig. 5

Port numbers are marked on the

black portion

To Port 1

To Port 2

To Port 3

4.4.2 ENABLE AND DISABLE THE OUTPUT

You can use Port 7 and 8 to remote control the OUTPUT ON/OFF.

a) Open Port 7 and 8 if you want to ENABLE the output ( By default )

b) Short Port 7 and 8 if you want to DISABLE the output.

4.5 If you do not use the remote control feature, make sure the remote control ON/OFF switch is in OFF

position(Rear panel).

4.6 Switch on the power supply and the power ON/OFF LED should light up in green.

Then, adjust the output voltage to the desired voltage and switch off the power supply.

4.7 Connect the equipment to the power supply. Red (+) is connected to the positive polarity input of the

equipment and Black (-) is connected to the negative polarity input of the equipment.

4.8 Switch on the power supply first and the LED Indicator should light up in green.

4.9 Switch on the equipment and the LED Indicator should still remain in green.

4.10 You can now operate the equipment.

When an operation is finished, switch off the equipment first and then switch off the power supply.

4.11 When disconnecting the power supply from the unit, disconnect the remote sensing wire first, then

disconnect the output cables.

5. SPECIFICATIONS

SPS

9600

SPS

9602

Variable Output Voltage 1 ~ 15V 1 ~ 30V

Total Rated Output Current

(

Main + Auxiliar

Out

)

60A 30A

Rated Output Current (Main) 60

30A

Rated Output Current (Auxiliary) 5

Ripple and Noise 40mV

Load Regulation 0.1% + 5mV

Line Regulation 0.05% + 3mV

Input Voltage 230VAC / 50Hz

(

or on re

uest

)

Efficiency >85%

Dynamic Power Factor Correction >0.97 at o

timal load

Voltmeter and Ammeter Display 3 di

it LED dis

Meter Accurancy +/- 1% + 1 coun

Indicator Green LED for power on/off indication

Red LED for overload/short circuit indication

Special Feature Remote Control & Remote Sensin

Cooling Method Variable S

eed thermal static control fan

Operating Temperature 0 ~ 40°C

Protections Overload(Constant Current Limiting), Short Circuit,

Overtemperature and OVP

Approvals CE-EMC: EN 55022 CE-LVD:EN 60950

Dimension 220

(

)

(

)

110 x 360

(

)

Weight 5.8K

7673-9602-0002

Questo manuale è adatto per i seguenti modelli

Altri manuali Manson Engineering Industrial Alimentazione elettrica

Manson Engineering Industrial

Manson Engineering Industrial SPA-8230 Manuale utente

Manson Engineering Industrial

Manson Engineering Industrial HCS-3202 Manuale utente

Manson Engineering Industrial

Manson Engineering Industrial ZVS-8350 Manuale utente

Manson Engineering Industrial

Manson Engineering Industrial SPA-8150 Manuale utente

Manson Engineering Industrial

Manson Engineering Industrial HCS-3200 Series Manuale utente

Manson Engineering Industrial

Manson Engineering Industrial HCS-3400-USB Manuale utente

Manson Engineering Industrial

Manson Engineering Industrial HCS-3100 Series Manuale utente

Manson Engineering Industrial

Manson Engineering Industrial ZPS-9160 Manuale utente

Manson Engineering Industrial

Manson Engineering Industrial SPA-8330 Manuale utente

Manson Engineering Industrial

Manson Engineering Industrial HCS-3404 Manuale utente

Manson Engineering Industrial

Manson Engineering Industrial NEP-8323 Manuale utente

Manson Engineering Industrial

Manson Engineering Industrial EP-907 Manuale utente

Manson Engineering Industrial

Manson Engineering Industrial NTP-6521 Manuale utente

Manson Engineering Industrial

Manson Engineering Industrial NRP-3630 Manuale utente

Manson Engineering Industrial

Manson Engineering Industrial NTP-5521 Manuale utente

Manson Engineering Industrial

Manson Engineering Industrial KPS-6000 Series Manuale utente

Manson Engineering Industrial

Manson Engineering Industrial HCS-3600 USB Manuale utente

Manson Engineering Industrial

Manson Engineering Industrial NEP-8323 Manuale utente

Manson Engineering Industrial

Manson Engineering Industrial SPS-9620 Manuale utente

Manson Engineering Industrial

Manson Engineering Industrial NEP Series Manuale utente

Manson Engineering Industrial

Manson Engineering Industrial HCS Series Manuale utente

Manson Engineering Industrial

Manson Engineering Industrial SDP Series Manuale utente

Manson Engineering Industrial

Manson Engineering Industrial SSP-9081 Manuale utente

Manson Engineering Industrial

Manson Engineering Industrial SSP-9080 Manuale utente

Manuali Alimentazione elettrica popolari di altre marche

Monacor

Monacor PS-12CCD Manuale utente

VOLTIMA

VOLTIMA MagicBox 15 Manuale utente

Agilent Technologies

Agilent Technologies 6032A Manuale utente

Miller

Miller Auto Deltaweld 452 Manuale utente

BCP

BCP PUOUBK Foglio di istruzioni

HC 2210 Manuale utente

Puls

Puls CT5.241 Manuale utente

OCZ

OCZ ZX1250W Manuale utente

iseg

iseg ECH 238 Manuale utente

Power

Power XXL A Series Manuale utente

Agilent Technologies

Agilent Technologies 6631B Manuale utente

Renogy

Renogy PHOENIX 300 Manuale utente

HP 6200B Manuale di servizio

Epson

Epson Stylus Scan 2500 Manuale operativo

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuale utente

Puls

Puls MiniLine ML50.100 Manuale utente

Puls

Puls AS-Interface SLA4.100 Manuale utente

Kenwood

Kenwood PS-60 Manuale utente