MantelMount SBK00 Manuale utente

Installation Instructions

SBK00 Soundbar Adapter Kit

Contains important safety information – please save! MantelMount.com

If you need help, call 1.800.897.9755 ext.1

For missing/damaged parts or questions during installation, please

contact our Customer Support team at 1.800.897.9755 ext.1 or

support@mantelmount.com. Customer satisfaction is our highest priority!

Watch an installation video or access a PDF of this manual at

MantelMount.com/FAQs/Specs and Manuals.

WARNING!

This product contains small parts

that can be a choking hazard. Do

not let children play with any of

these small parts! Keep children

away from the work area during

installation.

Caution

This product is intended to

be installed by professional

installation contractors, or

persons familiar with the tools

and methods required for this

installation. If you are not sure

about your ability to perform this

installation, you must contact a

professional. MantelMount is not

responsible for damage or injury

caused by incorrect installation or

improper use.

Caution

Do not let children operate, pull

on, or hang from MantelMount. Do

not let children push MantelMount

upward to the top position - this

will cause the mount to slam

against the wall due to the upward

force of the springs. Only a person

tall enough to control the mount

all the way to the top should

operate MantelMount.

Caution

Do not use this product in any

way, or for any purpose, that is

not specically described in these

instructions. MantelMount is not

responsible for damage or injury

caused by incorrect installation or

improper use.

NOTES:

A. This kit requires some parts

and instruction steps from a

MantelMount TV mount.

B. Any part numbers that are

referenced in these instructions

that are lower than {80} are

parts that come from the

MantelMount Mount.

C. Most installations will not use

all of the parts in this kit.

NOTE: If installing above a Mantel, add an additional 1.5 inches of clearance to the Minimum Height Chart

measurement found in your MantelMount installation guide.

SBK00 Installation Instructions

BEFORE INSTALLATION

Before you begin, please verify that all components are included and undamaged. If any parts are missing or damaged, contact

MantelMount. Never proceed with missing or damaged parts!

Lay out all components and make sure you identify that each one has a match in the diagram. Some of the parts included will

not be used during installation. Do not proceed if you do not understand and identify all of the components.

9594

ITEM NO. PART NO. DESCRIPTION QTY

81 15061 SB L BRACKET 2

82 15059 SB FRONT CRADLE 2

83 15080 LONG DEPTH ADJUST 2

84 15081 SHORT DEPTH ADJUST 2

85 15010 SOUNDBAR WING 2

86 15083 CARRIAGE BOLT M6 X 12 12

87 12183 LOCKNUT M6 20

88 12122 PLASTIC SPACER 8

89 14056 TV BRACE EXTENDER 2

90 15082 ROUND SCREW M4 X 6 8

91 12194 ROUND SCREW M6 X 30, SILVER 4

92 15012 SOUNDBAR SCREW M6 X 16 2

93 12166 WASHER M6 8

94 12139 VELCRO STRIP HOOK 4

95 12141 VELCRO STRIP LOOP 4

96 15065 FOAM TAPE 5mm X 20 X 120, BLACK 2

97 SBKITM INSTALLATION MANUAL 1

2 Verify you have the required tools:

1 Verify all parts are included.

4 mm

10 mm

Allen

Wrench

Wrench Socket

Wrench

Phillips

Screwdriver

Note: You may need to supply your own bolts to attach to soundbar holes.

Customer Support 1.800.897.9755 x1 suppor[email protected] 3

These following images show all the parts included with this kit. Most installations will not use all these parts.

BEFORE INSTALLATION

3 Review parts description:

Soundbar Wing {85}

Rotates to reach holes in the back of a

soundbar that are high, low, or wide.

Long and Short Depth Adjust

Change the Depth of the soundbar so the

front can be flush with the TV and adjust tilt.

Front Cradle {82}

Supports a soundbar that does

not have available screw holes.

“L” Bracket {81}

Attaches to the holes that are in

the bottom of a soundbar.

{86}

{88}

{86}

{91}

{85}

{90}

{82}

{81}

{87}

{93}

*Use the hardware provided by your soundbar manufacturer to secure your soundbar to cradle or wings.

SBK00 Installation Instructions

BEFORE INSTALLATION

If installing above a Mantel, add an additional 1.5 inches of clearance to the Minimum Height Chart measurement found

in your MantelMount installation guide.

The SBK00 is designed to be used with all models of the MantelMount. Review the following images and choose your

setup for the correct installation configuration diagram.

4 Confirm your MantelMount model.

Conguration for most MantelMount Models

Conguration for Recess Box. See page 10-11 Does your TV need a TV Brace Extender? See page 6

Conguration for MM340. See page 9

Customer Support 1.800.897.9755 x1 suppor[email protected] 5

BEFORE INSTALLATION

The SBK00 was engineered to be used withvarious makes and models of soundbar. The following information

will help you determine which configuration will work best for your soundbar mounting situation.

5 Determine your Soundbar requirements

Use Velcro tape on

the back and bottom

Use foam tape at the front

and the back, cut to size.

Front Cradle {82}.

“L” Bracket {81}

{92}

Use Velcro tape on

the back and bottom

Use foam tape at the front

and the back, cut to size.

Front Cradle {82}.

“L” Bracket {81}

{92}

Use Velcro tape on

the back and bottom

Use foam tape at the front

and the back, cut to size.

Front Cradle {82}.

“L” Bracket {81}

{92}

Use Velcro tape on

the back and bottom

Use foam tape at the front

and the back, cut to size.

Front Cradle {82}.

“L” Bracket {81}

{92}

Use Velcro tape on

the back and bottom

Use foam tape at the front

and the back, cut to size.

Front Cradle {82}.

“L” Bracket {81}

{92}

Soundbar with Hanging Slots

For soundbars that use hanging slots instead

of threaded inserts. The SBK00 supplies special

screws {92} as shown. The flat surfaces on

the threads allow the screw to be held with a

wrench while a nut {87} secures the soundbar

to the SBK00.

*Use the hardware provided by your soundbar manufacturer to secure your soundbar to cradle or wings.

Soundbar with Holes on the Bottom

For a soundbar that is flat and deep, with holes

in the bottom. This soundbar will require the

L-Brackets and possibly the Cradles.

For Wider Soundbars

For a soundbar with holes that are a very wide

distance apart. This soundbar will require the

Soundbar Wings.

NOTE: If the holes are wide and located in the

bottom of the soundbar, the L-Brackets can be

mounted to the Soundbar Wings.

For Soundbars with no Mounting Holes

A Soundbar that does not have any accessible holes

can be supported with the front Cradles. Use the

supplied Velcro tape at the back or bottom to secure

the soundbar, and use the supplied foam tape at the

front of the Cradle to squeeze the soundbar while you

tighten the screws {90} and secure the Cradles.

Soundbar with Holes on the Back

For a soundbar that is tall and shallow, with

holes in the back. This soundbar might require

the Soundbar Wings to get the correct height.

SBK00 Installation Instructions

Assembling with TV Brace Extenders

The Speaker Kit works with TVs that require the TV Brace

Extender to reach the lower screws on the TV. If this is the

case, then the Brace Extenders need to be inserted into the

Vertical Braces the opposite as stated in the Manual for the

MantelMount. A washer will have to be installed between the

extender and TV to ll the gap.

Long or Short Adjust Bracket can be attached to the Brace

Extender or through both Vertical Brace and Brace Extender.

Depth Adjust Placement

The Depth Adjust Parts Can be attached in various

congurations to avoid speaker attachment points and to

get the best speaker and handle height. Shown below are

two examples:

Example One: Full Depth, Outside Attachment

Example Two: Full Depth, Inside Attachment

SBK00 INSTALLATION

Customer Support 1.800.897.9755 x1 suppor[email protected] 7

1. Attach Long Depth Adjust (light blue) to Vertical Brace

2. Attach Short Depth Adjust (blue) to TV Brace Extender

3. Connect the 2 with the M6 Carriage Bolt and Nut

4. The Tilt and depth can be adjusted by sliding the short

depth adjust on the long depth adjust and tightening

the carriage bolts.

The Maximum Depth to make the soundbar flush with the

front of the TV depends on the Thickness of the TV.

Depth Adjust Assembly

The soundbar bracket can be installed on the back of the TV before

hanging on the mount, or after the TV has been hung on the mount.

Back View

Front View

Tilt Adjust

Depth Adjust

TV Thickness

Depth of

Soundbar to

make flush

with TV

3in (75mm)

Max Depth to

front of mount

SBK00 INSTALLATION

SBK00 Installation Instructions

{88}

{87}

{86}

{90}

{86}

{93}

{87}

{93}

SBK00 INSTALLATION

Height Adjustment Soundbar Wings

Optional Mounting: Tall Soundbar Note in this

image that the Soundbar Wings are rotated upward

and attached to the holes in a tall soundbar in order

to allow the MantelMount Handle to reach down

below the soundbar.

Use Spacer for back of soundbar.

4 5

Assembling Soundbar Attachments

Reference Page 5 to determine which method works best for you to attach the Soundbar.

*Use the hardware provided by your soundbar manufacturer to secure your soundbar to cradle or wings.

Customer Support 1.800.897.9755 x1 suppor[email protected] 9

MM340 Only MM340 Only

SBK00 INSTALLATION

{90}

{88}

{91}

{87}

{93}

{86}

Determine which method you wish to use to attach the soundbar:

Soundbar Wings, the L-Brackets, or the Cradles. The cradles do

not need to be attached at this time.

MM340 does not have a Horizontal Brace so the Soundbar Wings

are used instead to provide some width and also a mounting

platform for the L-Brackets. All other mounts have a Horizontal

Brace for mounting.

MM340 requires Spacers {88} and longer Screws {91} when

mounting the Soundbar Wings to the Handles.

The L-Brackets are only used for holes in the bottom of the

soundbar, or to install the Cradles for a soundbar without

accessible holes. Otherwise, the soundbar can be attached

directly to the Soundbar Wings.

6 7

* Use the hardware provided by your

soundbar manufacturer to secure

your soundbar to cradle or wings.

SBK00 Installation Instructions

Tilt Adjust

Recess Box Recess Box

Wall Wall

.75in (20mm)

Depth to front

of mount

SBK00 RECESS BOX INSTALLATION

Since the recess box is closer to the wall, the Long Depth Support can NOT be used with a recess box. Only the

Short Depth support is used. If using the Horizontal Recess Brace with the Recess Box, the SBK00 Soundbar Kit will

not work.

Recess Box Assembly Since the recess box is closer to the wall, the Long Depth Support can NOT be used with a recess box. Only the

Short Depth support is used.

Depending on the thickness of the TV and depth of the soundbar, the 2 may not be flush. But you will still get an extra .75” (20mm) of

soundbar depth and tilt adjust.

Recess Box Adjustments

Horizontal Recess Brace

Indice

Altri manuali MantelMount Adattatore

MantelMount

MantelMount SSB40 Manuale utente

Manuali Adattatore popolari di altre marche

PCB Piezotronics

PCB Piezotronics 090B274 Manuale utente

Auvidea

Auvidea J20 Manuale del prodotto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuale utente

Akribis

Akribis ITF-21-BISS-MIT Manuale utente

Tenda

Tenda W54U Manuale utente

ROHO

ROHO AGILITY Manuale utente

PROLiNK

PROLiNK WN2001 Manuale utente

Hawking

Hawking HUF2 Manuale utente

Airlink101

Airlink101 AWLC4030 Manuale utente

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuale utente

Philips

Philips SWA4554S/10 Manuale utente

JVC

JVC TS-C9D2B Manuale di istruzioni

NETGEAR

NETGEAR A6100 Manuale utente

D-Link

D-Link DWA-121 Manuale utente

Philips

Philips SWA2037 Manuale utente

Basalte

Basalte 0610-20 Manuale utente

Yealink

Yealink EHS40 Manuale utente

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuale utente