Mark LX 50G PRO Manuale utente
LX 50G PRO
Rev 1.0
User Manual / Manual de Uso
Unpacking
Thank you for purchasing this product. Please read user guide for safety and
operations information before using the product. Keep this manual for
reference. This product can create perfect laser programs and effects since it
has passed a series
of strictly tests before delivery. Please check the
attachments listed on the page after opening the carton. In the event of carton
damage or attachment missing in transit, please contact your dealer or our after
sales service department.
Attachments:
1. Laser device LX 50 G PRO: 1PCS 2. Power Cable: 1PCS
3. User Guide: 1PCS
Notice:
1. Do not exposure the human eye directly to laser beam.
2. Do not turn on and off the laser frequently
3. Makes sure the power supply connects ground wire before using.
4. This unit is intended for indoor use only and should be prevented from
water,
moisture and shade. The working temperature of this unit is 18-30º C.
5 .Do not use this continuously over 4
hours,
otherwise it shortens the lifetime
of the unit.
6. Use clean tissue to remove the dust absorbed on the external lenses
periodically to optimize light output.
7. Do not remove or break the warranty label, oth
erwise it void the warranty.
8. Replace
fuse
with exact the same type as ours.
Any wrong fuse replacement
which is not specified fuse might cause fire or electric shock and damage your
unit. That will overstep our manufacture’
swarranty.
PAG. 1 User Manual/Manual de Instrucciones LX 50G PRO
EN
Warning
High
voltage
and danger!
No dismantle and staring
Warning:
1. Cut the power off for installment or repair.
2. The danger grade of laser is CLASS IIIB. Ensu re the observing
time inside the laser beam less than 10 seconds and minimum
distance 13 cm for safety.
3. Keep laser away from combustible above 0.5meter.
Technical parameter:
1. Power supply:AC110V~240V/50-60Hz
2. Wavelength: Green 532 nm
3. LASER power: 50 mW
Consumption: 50W
DMX Channels: 13 channels
4.
Scanning angle:
5.
7. Scanner speed: > = 10K PPS
6.
8. Control modes: auto/sound activate/master and slave/DMX 512
9. Dimensions: 275*195*130 mm
10. Weight: 1.5 Kg
Features:
0~+/-30°
This laser unit employs the latest scanner technique
and can project
out many cartoon, text and 3D effects like star, round, time -tunnel,
letter, geometry
graphics.
Pre-built 55
laser patterns of the
latest performance effects
and it
can discretional control the pattern by DMX controller.
PAG. 2 User Manual/Manual de Instrucciones LX 50G PRO
EN
Front
panel
Back
panel
description
1 Power switch
2
Address code
3
DMX IN/OUT
4
Power supply with fuse
5
Hang
ring of safety rope
6
7
MIC
Sound sensitivity knob
PAG. 3 User Manual/Manual de Instrucciones LX 50G PRO
LASER OUTPUT
EN
Operation
Stand-Alone Operation
1.
Setting the work mode according to your requirement to set the mode
：
SOUND ACTIVE or AUTO MODE see the function setting chart.
2.
Connecting the power the unit start to work, beam come out.
3.
For SOUND ACTIVE mode adjust the sound sensitivity knob on the back
of the unit to
make
the unit more or less sensitive to sound active
Mode is running
; Auto
automatically.
Master-Slave Mode
1.
Setting the work Mode. Choose a unit to function as master mode,
set dipswitch to select Sound Active or Auto mode. T he other must
be set to Slave mode, set dipswitch to select
Slave mode. Master
unit controls the slave unit.
2.
Use standard XLR microphone cable to chain your units together
via the XLR connector on the rear of the units. For longer cable runs we
we suggest a terminator
at the last fixture
3.
Turn on the all units power, the units begins reset, then the unit
begins working. The slave units will react the same as the master
unit
4.
In sound active mode, adjust audio
sensitivity knob to make the unit
more or less sensitive
in sound active; in Auto mode, the unit
is
running automatically
PAG. 4 User Manual/Manual de Instrucciones LX 50G PRO
EN
DMX Mode
1.
Setting work mode, the system only accepts the DMX512 signal
of international
standard to control the system
mode, and also
dispatched the address channel of DMX, please see the
function
seeing chart.
2. Connect the controller line,usestandard XLR -XLR microphone cable
from DMX512 ou tput connect to link jack of the first unit, and
from the link jack of first unit to the second’s input port, and do
as this chained all units.
3. Connect the power supply, use DMX512 control console.
Note: Do please connect one loop insert to output sign al of the
terminal
unit ,
this loop inserter must be placed between to the
2 pin and 3 pin of the jack,pleaseconnect one 120Ω resistance.
PAG. 5 User Manual/Manual de Instrucciones LX 50G PRO
EN
0
0
0
0
0
0
0
0
0
0
SOUND ACTIVE
1
0
0
0
0
0
0
0
0
0
AUTO BEAM
0
0
0
0
0
0
0
0
1
0
AUTO ANIMATION
0
1
0
0
0
0
0
0
0
0
SLAVE MODE
SET DMX ADDRESS CODE 1 DMX
Dipswitch
Value
Dipswitch Value
#2
1
#7
32
#3
2
#8
64
#4
4
#9
128
#5
8
#1
256
#6
16 #10 DMX set to“1”
0
#1
#2
#3
#4
#5
#6
#7
#8
#9
#1
0=OFF 1=ON
DISPWITCH CHART /Code Number Working mode
Address
code
setting
Please see the sheet attached.
Up means “ON” shown wi th “1”
Down means “OFF” shown with “0”
For DMX mode, the system only accept the DMX 512 signal of international
standard to control the system mode. Address from 1-9 dispswitch must be set.
The address is set from 1 to 511. Each dipswitch represents a binary value.
Example:
When setting, as long as you select the dipswitch account to value of the
binary is equal to the address you set, it is OK. The unit uses 13 channels
to DMX control. Please see the chart table.
PAG. 7 User Manual/Manual de Instrucciones LX 50G PRO
EN
13
channel description
Channel
DMX512
Content
1. Control mode
0~51
Sound Active(3~13ch
invalid)
52-103
Auto Beam(3~13ch
invalid)
104-155
Auto－Animation
156-207
Manual, sound trigger
208-255
Manual, auto trigger
2. Open &Closed
0~85
closed
86-171
Open \Blanking
172-255
No blanking
3. Change of Patterns
0~225
55 patterns（0~255）
4. Speed
0~255/23=0~11
12 graded speed（0~11）
5. Rolling
0~63
Non-rolling
64~127
Horizontal Rolling
128~191
Vertical Rolling
192~255
Horizontal &Vertical Rolling
6.
0~63
64-127
128-191
192-255
PAG. 8 User Manual/Manual de Instrucciones LX 50G PRO
pattern &rotation
No function
Clockwise rotation
Dotted pattern
Dotted pattern and rotation
EN
192~255 Horizontal & Vertical stretch
9.
Zoom
0-85
NO ZOOM
86-169
one point to large
170-255
large to one point
10.
Slow - Draw Speed
0~5
No function
6~255
43 graded speed (6~255)
11. Scanning speed
0-255 255 graded speed (Fast to
slow)
12. Color changing
speed
(6~255)/23 NULL
13. Size of pattern
0~2 NULL
(3~255) 42 grade zoom out
7.
0~63
64-127
128-191
192-255
8. Stretch
0~63
Non-stretch
64~127
Horizontal stretch
128~191 Vertical stretch
PAG. 9 User Manual/Manual de Instrucciones LX 50G PRO
Rotation
&Point-draw
Non-rotation & non point draw
Rotation
Point draw
Rotation &Point-draw
EN
In stand-Alone operation
and in the
state of close if the power supply
red indicator is light up, and the
sound active indicator
light is light
up.
Its fault
to set up as Slave mode
please set up as master mode.
In DMX mode, the laser is off and
the DMX signal indicator is
unlighted
Make sure to set up the DMX mode,
and make sure to have a good
connection.
In DMX mode, the unit can ’t be
controlled by the DMX console, but
the DMX signal indicator I flashing.
Please make sure the DMX console
and unit have the same channel.
In stand-Alone operation and in the
state of close if the power supply
red indicator is light up, and the
sound active indicator
light isn’t light
up.
Because sound is too small make for
laser shut off in sound active, please
increase the music
volume or
increase audio sensitivity with
sensitivity knob.
PAG. 10 User Manual/Manual de Instrucciones LX 50G PRO
Troubleshooting
Trouble
Solution
IF the power supply indicator
doesn’t light up and the laser
doesn’t work.
Please check the power supply and
the input voltage.
In stand-Alone mode, if the pattern
direction is offset, a part of pattern
was shading beam.
Maybe
voltage of the power supply
is too low , causing
the motor can ’t
work well. Please make sure the
range of the motor voltage
within
±10V,and please use the low voltage
regulator.
EN
Indice
Lingue:
Altri manuali Mark Proiettore
Mark
Mark BIG FLASH II 1500 Manuale utente
Mark
Mark BEAM SPOT Manuale utente
Mark
Mark LX 100 RGB Manuale utente
Mark
Mark Superparled Eco Manuale utente
Mark
Mark SUPERPARLED 336 S Manuale utente
Mark
Mark MBAR 120 Manuale utente
Mark
Mark SUPERBAT LED WI 712 Manuale utente
Mark
Mark MAM 120 TROLLEY Manuale utente
Mark
Mark MBAR 612 BAT WI Manuale utente
Mark
Mark MAX 3 BT Manuale utente
