Martin Professional MAC 2000 Profile II Manuale utente

MAC 2000 Profile

user manual

743

613

488

171

408

10° 28°

133½°133½° 271

759

270°270°

490

530

545

min c/c

means, without permission in writing from Martin Professional A/S, Denmark. Printed in Denmark.

P/N 35000090 Rev. H

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

MAC 2000 Profile safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

TRANSPORTATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Included items. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Transport locks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Single flight case. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Double flight case. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

LAMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

About the HMI 1200 W/S lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Lamp replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

AC POWER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Power supply settings for magnetic ballast version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Power supply settings for electronic ballast version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Power connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Connecting fixtures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

RIGGING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

CONTROL PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Navigation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

DMX address and protocol setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Tailoring performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Readouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Service messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Service utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

OPTICAL CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Gobos. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Rotating gobo wheels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Color/gobo wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Effect wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

EFFECTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Dimming and strobe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Color mixing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Color temperature correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Random color mixing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Fixed colors and gobos. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Gobos. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Effect wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Iris. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Focus and zoom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Pan and tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Speed control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

ROUTINE MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Software installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

DMX PROTOCOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

CONTROL MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

ADJUSTMENT SUBMENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

DISPLAY MESSAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

CIRCUIT BOARD CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

4 MAC 2000 Profile

NTRODUCTION

Thank you for selecting the MAC 2000 Profile. This extraordinary 1200 watt luminaire from Martin Professional

provides CMY color mixing, continuous 0 - 178 mireds color correction, a color/gobo wheel with 4 dichroic color

filters and 3 fixed glass gobos, 10 indexed-rotation gobos on 2 wheels, a 2-position rotating-effect wheel with 3-facet

prism, beam shaper, and variable frost; combined full-range dimmer and shutter, iris, zoom, focus, 540° of pan, and

267° of tilt. It is available with a magnetic or electronic ballast.

For the latest firmware updates, documentation, and other information about this and all Martin Professional products,

please visit the Martin web site at http://www.martin.dk.

MAC 2000 Profile safety information

Warning! This product is for professional use only. It is not for household use.

This product presents risks of lethal or severe injury due to fire and heat, electric shock, ultraviolet radiation, lamp

explosion, and falls. Read this manual before powering or installing the fixture, follow the safety precautions listed

below and observe all warnings in this manual and printed on the fixture. If you have questions about how to operate

the fixture safely, please contact your Martin dealer or call the Martin 24-hour service hot line at +45 70 200 201.

TO PROTECT YOURSELF AND OTHERS FROM ELECTRIC SHOCK

• Disconnect the fixture from AC power before removing or installing the lamp, fuses, or any part, and when not in use.

• Always ground (earth) the fixture electrically.

• Use only a source of AC power that complies with local building and electrical codes and has both overload and

ground-fault protection.

• Do not expose the fixture to rain or moisture.

• Refer any service operation not described in this manual to a qualified technician.

TO PROTECT YOURSELF AND OTHERS FROM UV RADIATION AND

LAMP EXPLOSION

• Never operate the fixture with missing or damaged lenses and/or covers.

• When replacing the lamp, allow the fixture to cool for at least 15 minutes before opening the fixture or removing the

lamp. Protect your hands and eyes with gloves and safety glasses.

• Do not stare directly into the light. Never look at an exposed lamp while it is lit.

• Replace the lamp if it becomes defective or worn out, or before usage exceeds the maximum service life.

TO PROTECT YOURSELF AND OTHERS FROM BURNS AND FIRE

• Never attempt to bypass the thermostatic switch or fuses. Always replace defective fuses with ones of the specified

type and rating.

• Keep all combustible materials (for example fabric, wood, paper) at least 1.0 meter (39 inches) away from the fixture.

Keep flammable materials well away from the fixture.

• Do not illuminate surfaces within 1.0 meter (39 inches) of the fixture.

• Provide a minimum clearance of 0.1 meters (4 inches) around fans and air vents.

• Never place filters or other materials over the lens.

• The exterior of the fixture can get very hot. Allow the fixture to cool for at least 5 minutes before handling.

• Do not modify the fixture or install other than genuine Martin parts.

• Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).

TO PROTECT YOURSELF AND OTHERS FROM INJURY DUE TO FALLS

• Do not lift or carry the fixture alone.

• When suspending the fixture, verify that the structure can hold at least 10 times the weight of all installed devices.

• Verify that all external covers and rigging hardware are securely fastened and use an approved means of secondary

attachment such as a safety cable.

• Block access below the work area whenever installing or removing the fixture.

Transportation 5

RANSPORTATION

Important! Release the transport locks before operating the fixture.

Included items

The MAC 2000 Profile is shipped in a 1 or 2 unit flight case that

contains the following items.

• User manual

• 2 clamp attachment brackets

Transport locks

The head and yoke may be locked for transportation and service.

The locks are shown in Figure 1. The fixture must be unlocked

before operation.

Single flight case

To unpack the fixture

1 Remove the top of the flight case.

2 With one person on each side, lift the fixture out of the

bottom of the flight case.

3 Release the pan and tilt locks before operating.

To pack the fixture

1 Disconnect the fixture from power and allow it to cool.

2 Lock the head and yoke in the position shown in Figure 2.

3 Place the fixture in the bottom of the flight case. Place the

top section over the fixture without forcing.

Figure 1: Pan and tilt locks

Figure 2: Single unit transport position

6 MAC 2000 Profile

Double flight case

To unpack

1 Open the flight case and pull the drawer all the way out.

2 Release the head (tilt) transport lock.

3 Install rigging hardware as described on page 12.

4 With one person on each side, lift the fixture out of the flight

case.

To pack

1 Disconnect the fixture from power and allow it to cool.

2 Turn the yoke parallel to the sides of the base with the tilt

lock closest to the back.

3 Pull the transport drawer all the way out. With one person

on each side, place the fixture on the drawer with the arrow

pointing in.

4 Remove and stow rigging hardware. Coil and stow the

power cord in the door.

5 Tilt the head so that the lens points away from the door as

shown in Figure 3. Lock the head in the horizontal position.

Do not lock the yoke.

6 Slide the drawer all the way in without forcing. Close the

flight case.

To setup for flight case testing

The double flight case has two slide-out arms from which the fixture can hang for testing and setting. Though

unnecessary, the pan and tilt reset can be cancelled by pressing [Menu] and [Enter] at the same time.

1 Open the flight case and pull the drawer all the way out. Release the transport locks.

2 Pull the test arms all out. Tilt the fixture up and over the slide arms so that the handle cross-braces that are

second from the back rest on the arms. The fixture should rest at an angle.

3 Push the transport drawer into the flight case.

Figure 3: Double unit transport position

FRONT

Lamp 7

AMP

About the HMI 1200 W/S lamp

The MAC 2000 Profile comes with a double-ended OSRAM

HMI 1200 W/S discharge lamp installed. This highly-efficient

short-arc source provides an exceptionally stable 6000K color

temperature, a color rendering index greater than 90, and an

average life of 750 hours.

The lamp is capable of hot restrike. This feature, however, is only

supported by the MAC 2000 Profile with electronic ballast.

The ends of the lamp have specially-developed keys, shown in

Figure 6, to ensure proper installation. Do not use HMI 1200 W/S

lamps with the non-keyed SFc 10-4 base.

Warning! Installing any other lamp may create a safety

hazard or damage the fixture!

The lamp has an average life of 750 hours. To reduce the risk of

explosion, replace the lamp before usage exceeds 125% of the

average life, i.e., before it exceeds 940 hours. To read lamp hours

from the control panel, please refer to “Readouts” on page 15.

For optimum performance, avoid turning off the lamp before it

has warmed up fully.

Lamp replacement

Important! Do not touch the quartz bulb with bare fingers.

Replacement lamps are available from your Martin dealer. Please

order Martin P/N 97010304.

The clear quartz bulb must be clean and free of any oils from

your fingers. Clean the lamp with an alcohol wipe and polish it

with a dry cloth, particularly if you accidentally touch the bulb.

To replace the lamp

1 Disconnect the fixture from power and allow it to cool. Lock

the head horizontally with the top up.

2 See Figure 4. Release the 4 quarter-turn fasteners marked

with arrows on the rear plate. Pull the lamp assembly

straight back as far as it goes and let it rest in place.

3 See Figure 5. Pull the retention spring on the left end up

and then swing the end of the lamp out. Pull the other end

out of the socket.

TOP

Figure 4: Lamp access

Figure 5: Lamp removal

8 MAC 2000 Profile

4 See Figure 6. With the nipple on the bulb facing the back,

insert the right end of the new lamp in the socket. Pull up

on the left spring and snap the other end into place.

5 Lift the lamp assembly so that lamp is level with the center

of the reflector. Push the assembly straight in until it seats,

making sure the lamp passes through the reflector opening.

Lock the 4 quarter-turn fasteners.

6 When installing a new lamp, reset the lamp hour and lamp

strike counters as described on page 15.

To align the lamp

1 Switch on the MAC 2000 Profile and allow it to reset. Using

either a controller or the control module, turn on the lamp

and project an open white beam on a flat surface.

2 Center the hot spot vertically using the top Allen-head

adjustment screw in the center of the rear plate.

3 If there is significant hot spot, turn the bottom adjustment

screw counterclockwise until the light is evenly distributed.

If the light is brighter around the edge than it is in the

center, or if light output is low, turn the bottom adjustment

screw clockwise until the light is bright and evenly

distributed.

4 Repeat step 2.

Figure 6: Lamp insertion

Figure 7: Lamp adjustment

AC power 9

POWER

WARNING! For protection from electric shock, the fixture

must be grounded (earthed). The AC mains supply

shall be fitted with a fuse or circuit breaker and

ground-fault protection.

Important! Verify the power supply settings before applying

power.

Power supply settings for magnetic ballast

version In the MAC 2000 Profile with magnetic ballast, both the

transformer and the ballast must be tapped correctly for the local

AC voltage and frequency. The wrong setting can cause

overheating, damage, and poor performance. The factory settings

are printed on the serial number label. Note: The 100 and 120 V

transformer settings are not used in the magnetic ballast version.

To change the power supply settings

1 Disconnect the fixture from AC power. Remove the rear

base cover as shown in Figure 8.

2 Find the transformer setting in Table 1. Move the brown

wire on the transformer connection block to the position

shown in Figure 9.

3 To expose the ballast connection block, remove the screws

from each end of the side plate and tilt it down (Figure 8).

4 Find the ballast setting in Table 2. Move the brown wire on the ballast connection block to the position shown

Figure 9.

5 Close the base before applying power.

AC frequency AC voltage Setting

50 - 60 Hz 200 - 218 V 208 V

50 - 60 Hz 219 - 240 V 230 V

50 - 60 Hz 241 - 250 V 250 V

Table 1: Transformer settings (magnetic ballast model)

AC frequency AC voltage Setting

50 Hz

200 - 218 V 208 V / 50 Hz

219 - 238 V 230 V / 50 Hz

239 - 250 V 245 V / 50Hz

60 Hz 200 - 218 V 208 V / 60 Hz

219 - 241 V 230 V / 60 Hz

Table 2: Magnetic ballast settings

Figure 8: Power supply access

ballast

transformer

230V/60Hz

230 V / 60 Hz

230V/50Hz

230 V / 50 Hz

245V/50Hz

245 V / 50 Hz

208V/60Hz

208 V / 60 Hz

208V/50Hz

208 V / 50 Hz

208 V

250 V

230 V

Figure 9: Transformer and ballast

connections

ballast transformer

10 MAC 2000 Profile

Power supply settings for electronic ballast version

In the MAC 2000 Profile with electronic ballast, the transformer must be tapped correctly for the local AC voltage. The

electronic ballast automatically adapts to the line voltage and frequency. The wrong transformer setting, though, can

cause overheating, damage, and poor performance. The factory setting is printed on the serial number label.

FUSES

Electronic ballast models that come factory set for 100 V or 120 V have two 20 A T (time delay) main fuses, which are

located near the power switch. Units set at 210 V and above have two 15 A main fuses installed.

If you change the voltage settings, alternate fuses are supplied in bag packed together with this user manual. Use:

• 15 A main fuses when the transformer is set at 208, 230, or 250 V

• 20 A T fuses when it is set at 100, or 120 V

To change the transformer setting

1 Disconnect the fixture from AC power. Remove the rear base cover as shown in Figure 8.

2 Find the transformer setting in Table 3. Move the brown wire on the transformer connection block to the

position shown in Figure 10.

3 Close the base before applying power.

Power connection

Important! Connect the MAC 2000 Profile directly to AC

power. Do not connect it to a dimmer system;

doing so may damage the fixture.

You may need to install a cord cap that fits your supply on the

power cable. A 3-prong grounding-type plug must be installed following the manufacturer’s instructions. The table

shows some possible pin identification schemes; if the pins are not clearly identified, or if you have any doubts about

proper installation, consult a qualified electrician.

To apply power, set the power switch on the base to the “I” position.

AC frequency AC voltage Setting

50 - 60 Hz 98 - 105 V 100 V

50 - 60 Hz 115 - 126 V 120 V

50 - 60 Hz 200 - 218 V 208 V

50 - 60 Hz 219 - 240 V 230 V

50 - 60 Hz 241 - 250 V 250 V

Table 3: Transformer settings, electronic ballast model

Wire Color Pin Symbol Screw (US)

brown live L yellow or brass

blue neutral N silver

yellow/green ground green

Table 4: Cord cap connections

Figure 10: Transformer connections

208 V

250 V

230 V

120 V

100 V

Altri manuali per MAC 2000 Profile II

Indice

Altri manuali Martin Professional Lanterna

Martin Professional

Martin Professional CYCLO 02 Manuale utente

Manuali Lanterna popolari di altre marche

KYOWA

KYOWA KW-9114 Manuale utente

Stahl

Stahl ECOLUX 6610 Series Manuale utente

SNOWJOE

SNOWJOE SUNJOE 24V-LGT500-CT Manuale utente

PRG

PRG VARI LITE VL5 Manuale utente

Raytec

Raytec VARIO2 series Manuale utente

ENSA

ENSA LEDBT18WS2 Manuale utente

LUG

LUG OFFICE LB LED N/T Manuale utente

GE Wallighter 250 Manuale utente

Draper

Draper RLEDL19/B Manuale utente

Green Lighting

Green Lighting TRI-SENSOR GL4612LU Manuale utente

Panasonic

Panasonic EY3741B57 Manuale utente

Clas Ohlson

Clas Ohlson LCC8T Manuale utente

Coolon

Coolon WDN-140 Manuale utente

Holiday Travel

Holiday Travel 834873 Manuale utente

BEGA

BEGA 84 036 Manuale utente

BEGA

BEGA 33 596 Manuale utente

Dale Tiffany

Dale Tiffany GT701162 Manuale utente

Wagan

Wagan Brite Nite Pop-Up USB Lantern Manuale utente