Martin Professional MAC 2000 Wash Manuale utente

MAC 2000 Wash

user manual

750 613

488

171

408

28°

133½°133½° 280

765

270°270°

490

562

min c/c

14°

means, without permission in writing from Martin Professional A/S, Denmark. Printed in Denmark.

P/N 35000114 Rev. H

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

MAC 2000 Wash safety information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

TRANSPORTATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Included items. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Transport locks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Cardboard box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Single flight case. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Double flight case. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

AC POWER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Power connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Reduced power function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Connecting fixtures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

RIGGING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

CONTROL PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Navigation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

DMX address and protocol setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Tailoring performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Readouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Service messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Service utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

EFFECTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Color. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Dimming and strobe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Color temperature correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Motorized zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Beam angles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Motorized barn-doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Aperture adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Pan and tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Speed control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

OPTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Color wheels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Changing the front lens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Changing the aperture ring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Installing the optional dimmer wheel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

ROUTINE MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

The lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Firmware installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

DMX PROTOCOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

16-bit protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

8-bit protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

CONTROL MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

ADJUSTMENT SUBMENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

DISPLAY MESSAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

CIRCUIT BOARD CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

4 MAC 2000 Wash

NTRODUCTION

Thank you for selecting the MAC 2000 Wash. The MAC 2000 Wash is a 1200 Watt moving head wash light

that provides CMY color mixing, color correction (CTC), two color wheels (each with four removable colors),

a combined dimmer/shutter. 540° of pan and 267° of tilt. A motorized barn-door system and optional

dimmer wheel are available as a separately orderable accessory.

The MAC 2000 Wash has a Fresnel lens fitted as standard, and is also supplied with a PC lens and a

super-wide-angle lens. A motorized zoom provides beam angle ranges of 11° through to 40° (in the

standard Fresnel configuration), 12° through to 34° (with the PC lens fitted), or 66° through to 80° (with the

super-wide-angle lens fitted).

The MAC 2000 Wash is fitted with an electronic ballast that provides flicker-free operation and an

economical power-saving mode. The power supply unit is switchable to match 100 - 130 V or 200 - 250 V

local power supplies.

Note: This manual describes functionality available from version 1.7 of the MAC 2000 Wash

firmware. For the latest firmware updates, documentation, and other information about

this and all Martin Professional products, please visit the Martin web site at

http://www.martin.com.

MAC 2000 Wash safety information

Warning! This product is for professional use only. It is not for household use.

This product presents risks of lethal or severe injury due to fire and heat, electric shock, ultraviolet radiation,

lamp explosion, and falls. Read this manual before powering or installing the fixture, follow the safety

precautions listed below and observe all warnings in this manual and printed on the fixture. If you have

questions about how to operate the fixture safely, please contact your Martin dealer or call the Martin

24-hour service hot line at +45 70 200 201.

Protection from electric shock

• Disconnect the fixture from AC power before removing or installing the lamp, fuses, or any part, and when

not in use.

• Always ground (earth) the fixture electrically.

• Use only a source of AC power that complies with local building and electrical codes and has both overload

and ground-fault protection.

• Do not expose the fixture to rain or moisture.

• Refer any service operation not described in this manual to a qualified technician.

Protection from UV radiation and lamp explosion

• Never operate the fixture with missing or damaged lenses and/or covers.

• When replacing the lamp, allow the fixture to cool for at least 15 minutes before opening the fixture or

removing the lamp. Protect your hands and eyes with gloves and safety glasses.

• Do not stare directly into the light. Never look at an exposed lamp while it is lit.

• Replace the lamp if it becomes defective or worn out, or before usage exceeds the maximum service life.

Protection from burns and fire

• Never attempt to bypass the thermostatic switch or fuses. Always replace defective fuses with ones of the

specified type and rating.

• Keep all combustible materials (for example fabric, wood, paper) at least 1 meter (39 inches) away from the

fixture. Keep flammable materials well away from the fixture.

• Do not illuminate surfaces within 3 meters (10 feet) of the fixture.

• Provide a minimum clearance of 0.1 meters (4 inches) around fans and air vents.

• Never place filters or other materials over the lens.

Introduction 5

• The exterior of the fixture can get very hot. Allow the fixture to cool for at least 5 minutes before handling.

• Do not modify the fixture or install other than genuine Martin parts.

• Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).

Protection from injury due to falls

• Do not lift or carry the fixture alone.

• When suspending the fixture, verify that the structure can hold at least 10 times the weight of all installed

devices.

• Verify that all external covers and rigging hardware are securely fastened and use an approved means of

secondary attachment such as a safety cable.

• Block access below the work area whenever installing or removing the fixture.

6 MAC 2000 Wash

RANSPORTATION

Important! Release the transport locks before operating the fixture.

Included items

The MAC 2000 Wash is shipped in a cardboard box or in a

1 or 2 unit flight case that contains the following items.

• User manual

• 2 x 20 A main fuses (for use with 100-130 V local power

supply)

• 2 x 15 A main fuses (for use with 200-250 V local power

supply)

• 2 clamp attachment brackets

• XLR cable

Transport locks

The head and yoke may be locked for transportation and

service. The locks are shown in Figure 1. The fixture must be unlocked before operation.

Cardboard box

Instructions for removing models that have been shipped in a cardboard box are printed on the outside of

the box. The cardboard box is not designed for repeated use and for transportation of the fixture we strongly

recommend the use of one of our flight cases.

Single flight case

Unpacking the fixture

1 Remove the top of the flight case.

2 With one person on each side, lift the fixture out of the

bottom of the flight case.

3 Release the pan and tilt locks before operating.

Packing the fixture

1 Disconnect the fixture from power and allow it to cool.

2 Lock the head and yoke in the position shown in Figure 2.

3 Place the fixture in the bottom of the flight case. Place the

top section over the fixture without forcing.

Figure 1: Pan and tilt locks

Figure 2: Single unit transport position

Transportation 7

Double flight case

Unpacking

1 Open the flight case and pull the drawer all the way out.

2 Release the head (tilt) transport lock.

3 Install rigging hardware as described on page 11.

4 With one person on each side, lift the fixture out of the flight

case.

Packing

1 Disconnect the fixture from power and allow it to cool.

2 Turn the yoke parallel to the sides of the base with the tilt

lock closest to the back of the base.

3 Pull the transport drawer all the way out. With one person

on each side, place the fixture on the drawer with the

‘Front’ arrow pointing into the flight case.

4 Remove and stow rigging hardware. Coil and stow the

power cord in the door.

5 Tilt the head so that the lens points away from the door as

shown in Figure 3. Lock the head in the horizontal position.

Do not lock the yoke.

6 Slide the drawer all the way in without forcing. Close the flight case.

Setup for flight case testing

The double flight case has two slide-out arms from which the fixture can hang for testing and setting.

Though unnecessary, the pan and tilt reset can be cancelled by pressing [Menu] and [Enter] at the same

time.

1 Open the flight case and pull the drawer all the way out. Release the transport locks.

2 Pull the test arms out. Tilt the fixture up and over the test arms so that the handle cross-braces that are

second from the back rest on the arms. The fixture should rest at an angle.

3 Push the transport drawer into the flight case.

FRONT

Figure 3: Double unit transport position

8 MAC 2000 Wash

POWER

WARNING! For protection from electric shock, the fixture must be grounded (earthed). The AC mains

supply shall be fitted with a fuse or circuit breaker and ground-fault protection.

Power supply

The MAC 2000 Wash is shipped configured for 200 - 250 V at 50/60 Hz, but can be manually switched to

accept either 100 - 130 V or 200 - 250 V power supplies.

Switching to match local power supply voltage

1 Ensure the fixture is not connected to power.

Lock the head vertically

2 Remove the four screws in the corners of the

display-side top panel and lift the panel clear.

Avoid strain on the panel ground (earth) cable

by supporting the panel.

3 The power supply switch is located in the

base unit at the end furthest from the display

(see Figure 5).

4 Set the switch to 115 V for a 100 - 130 V AC

power supply. Set the switch to 230 V for a

200 - 250 V AC power supply.

5 Replace the panel and screws. Remember to

unlock the head before using the fixture.

Figure 4: Removing display side top panel

230 115

Figure 5: Power supply switch

AC power 9

Fuses

The MAC 2000 Wash is supplied with:

• two 20 AT (time delay) main fuses for use with AC supplies of 100 - 130 volts.

• two 15 A main fuses for use with AC supplies of 200 - 250 volts.

Install the appropriate fuses in the holders near the power switch.

Power connection

Important! Connect the MAC 2000 Wash directly to AC power. Do not connect it to a dimmer system;

doing so may damage the fixture.

You may need to install a cord cap that fits your supply on the power cable. A 3-prong grounding-type plug

must be installed following the manufacturer’s instructions. The table shows some possible pin identification

schemes; if the pins are not clearly identified, or if you have any doubts about proper installation, consult a

qualified electrician.

To apply power, set the power switch on the base to the “I” position.

Reduced power function

The MAC 2000 Wash has an automatic power reduction function, which reduces the consumption to 700W

if the shutter/dimmer is closed for more than 10 seconds. This not only increases the lamp life, but also

further decreases the overall noise emission of the fixture.

Wire Color Pin Symbol Screw (US)

brown live L yellow or brass

blue neutral N silver

yellow/green ground green

Table 1: Cord cap connections

10 MAC 2000 Wash

ATA

Important! Never connect more than 1 data input and 1 data output.

The MAC 2000 Wash has both 3-pin and 5-pin XLR sockets for DMX input and output. The pin-out on all

sockets is pin 1 to shield, pin 2 to cold (-), and pin 3 to hot (+). There is no connection to pins 4 and 5.

The sockets are wired in parallel: both inputs connect to both outputs. For reliable data transmission and to

avoid damage to the fixture, however, use one input and one output!

Connecting fixtures

• Use shielded twisted-pair cable designed for RS-485 devices: standard microphone cable cannot transmit

control data reliably over long runs. 24 AWG cable is suitable for runs up to 300 meters (1000 ft). Heavier

gauge cable and/or an amplifier is recommended for longer runs.

• Never use both outputs to split the link. To split the serial link into branches use a splitter such as the Martin

4-Channel Opto-Isolated RS-485 Splitter/Amplifier.

• Do not overload the link. Up to 32 devices may be connected on a serial link.

• Terminate the link by installing a termination plug in the output socket of the last fixture. The termination

plug, which is a male XLR plug with a 120 ohm, 0.25 watt resistor soldered between pins 2 and 3, “soaks

up” the control signal so it does not reflect and cause interference. If a splitter is used, terminate each

branch of the link.

• Martin fixtures introduced before 1997 have reversed polarity data sockets (pin 2 hot and pin 3 cold). The

socket polarity is labelled. Use a phase-reversing cable (see “Accessories” on page 47) between the MAC

2000 Wash and any Martin device with reversed polarity.

Connecting the data link

1 Connect the DMX data cable from the controller to the MAC 2000 Wash’s 3-pin or 5-pin input (male) socket.

2 Using the sockets that match your data cable, connect the output of the fixture closest to the controller to

the input of the next fixture.

3 Insert a male 120 ΩXLR termination plug in the 3-pin or 5-pin output of the last fixture on the link.

Indice

Altri manuali Martin Professional Riflettore

Martin Professional

Martin Professional CX-4 Manuale utente

Manuali Riflettore popolari di altre marche

Guangzhou Yinhe Lighting&Sound Equipment Factory

Guangzhou Yinhe Lighting&Sound Equipment Factory NE-204 Manuale utente

LIVARNO home

LIVARNO home 375304 2101 Istruzioni originali

Cameo

Cameo CLQS40WW Manuale utente

Leviton

Leviton Ellipsoid 5/50 Manuale utente

Monacor

Monacor img Stage Line PARL-56PDX/CR Manuale utente

Vector

Vector SL3AKV Manuale utente

Quantum

Quantum Q262 Manuale operativo

Philips

Philips Vari-lite VL3015LT Manuale utente

EUROSPOT

EUROSPOT C51 Manuale utente

DTS

DTS MINI BRICK ARC Manuale utente

Federal Signal Corporation

Federal Signal Corporation VISIBEAM II Manuale

ACME

ACME LED-MS350B Manuale utente

EuroLite

EuroLite Akku flat light 1 Manuale utente

Commercial Electric

Commercial Electric SPTM-1401 Manuale utente

Vision & Control

Vision & Control SLB-500-W5K7-P-SL Manuale utente

Teknik

Teknik FLEXI Manuale utente

Craftsman

Craftsman CMXLSB10 Manuale utente

EuroLite

EuroLite LED SLS-144 UV Floor Spot Manuale utente