Martin Wizard Manuale utente

Wizard

user manual

Measurements are expressed in millimeters.

552

516208

110

1 Data sockets

2 Power and Data LEDs

3 Power inlet & main fuse

4 DIP switch

5 Safety cable eye

6 Mounting bracket

7 Lamp housing

8 Swivel locks

9 Focus rod

Cover access screws

reproduced, in any form or by any means, without

permission in writing from Martin Professional A/S,

Denmark.

Printed in Denmark.

P/N 35000098, Rev. C

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Wizard safety information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

AC power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Installing a plug on the mains lead. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Adjusting voltage settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Wall mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Overhead mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Operation from the floor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Data connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Recommended cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Stand-alone operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Single unit operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Master / slave operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Stand-alone settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

MC-1 operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

MC-1 settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

DMX operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

DMX modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

DMX control address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Basic service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Lamp maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Setting 6- or 8-channel DMX mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Firmware updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

DMX protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

4 Wizard user manual

NTRODUCTION

Thank you for selecting the Martin Wizard. The Wizard is an automated lighting

fixture that provides:

• Strobe effects

• Seven solid colors, eight-split colors, and two white positions

• 13 gobos plus open

• A rotating parabolic reflector

• A rotating mirror drum with variable swivel angle

• Adjustable focus

• Mechanical shutter

• Multiple control options that enable a broad range of effects

The combination of the parabolic reflector and the mirror drum provide up to 84

individual beams with the current effect.

WIZARD SAFETY INFORMATION

Warning! This product is not for household use. It presents risks of

lethal or severe injury due to fire and heat, electric shock, and

falls.

Read this manual before powering or installing the fixture, follow the safety

precautions listed below and observe all warnings in this manual and printed on

the fixture. If you have questions about how to operate the fixture safely, please

contact a Martin distributor for assistance. Refer any service operation not

described in this manual to a qualified technician. Do not modify the fixture or

install other than genuine Martin accessories and upgrade kits.

Avoiding electric shocks

• Disconnect the fixture from AC power before removing or installing the lamp,

fuses, or any part, and when not in use.

• Always ground (earth) the fixture electrically.

Introduction 5

• Use only a source of AC power that complies with local building and electrical

codes and has both overload and ground-fault protection.

• Do not expose the fixture to rain or moisture.

• Refer all service to a qualified technician.

• Never operate the fixture with missing or damaged lenses and/or covers.

Protecting yourself and others from burns and fire

• Never attempt to bypass the thermostatic switch or fuses. Always replace

defective fuses with ones of the specified type and rating.

• Ensure that the air flow through fans and vents is free and unobstructed.

• Keep all combustible materials (for example fabric, wood, paper) at least 0.3

meters (12 inches) away from the fixture. Keep flammable materials well away

from the fixture.

• Do not illuminate surfaces within 0.1 meters (4 inches) of the fixture.

• Provide a minimum clearance of 0.1 meters (4 inches) around fans and air vents.

• Replace the lamp if it becomes defective or worn out, or before usage exceeds the

maximum service life. When replacing the lamp, allow the fixture to cool for at

least 5 minutes before opening the fixture or removing the lamp. Protect your

hands and eyes with gloves and safety glasses. It can take up to 15 minutes for the

fixture to cool completely.

• Never place filters or other materials over the lens or mirror drum.

• The exterior of the fixture can reach temperatures up to 60° C (140° F). Allow the

fixture to cool for at least 5 minutes before handling.

• Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104°

F).

• Do not stare directly into the light.

• Never operate the fixture without all lenses and covers installed: an unshielded

lamp can explode without warning and emits dangerous UV radiation that can

cause burns and eye damage.

Preventing injuries due to falls

• When suspending the fixture above ground level, verify that the structure can

hold at least 10 times the weight of all installed devices.

• Verify that all external covers and rigging hardware are securely fastened and use

an approved means of secondary attachment such as a safety cable.

• Block access below the work area whenever installing or removing the fixture.

6 Wizard user manual

UNPACKING

The packing material is carefully designed to protect the fixture during shipment -

always use it to transport the fixture.

The Wizard comes with the following:

• 1.5-meter, 3-wire IEC power cable.

• User manual.

AC power 7

POWER

The Wizard’s operating voltage is printed on the serial number label that can be

found on the back of the Wizard. Verify that the operating voltage closely

matches the AC supply voltage before applying power. Contact your Martin

dealer if the operating voltage differs from the supply voltage by more than five

percent.

INSTALLING A PLUG ON THE MAINS

LEAD

The fixture’s mains lead may require a grounding-type cord cap that fits your

power distribution cable or outlet. Consult a qualified electrician if you have any

doubts about proper installation.

Warning! For protection from dangerous electric shock, the fixture

must be grounded (earthed). The AC mains supply shall have

overload and ground-fault protection.

Important! Verify that the feed cables are undamaged and rated for the

current requirements of all connected devices before use.

Following the cord cap manufacturer’s instructions, connect the yellow and green

wire to ground (earth), the brown wire to live, and the blue wire to neutral. The

table below shows some pin identification schemes.

Wire Pin Marking Screw color

brown live “L” yellow or brass

blue neutral “N” silver

yellow/green ground green

8 Wizard user manual

ADJUSTING VOLTAGE SETTINGS

EU Model

1 Disconnect the fixture from AC power.

2 If the lamp is hot, allow it to cool for 5 minutes and wear safety goggles to protect

your eyes.

3 Remove the 6 cover-access screws and lift of the fixture cover.

4 On the transformer, move the BROWN wire to the transformer terminal shown in

the table above for the local AC supply voltage. The terminals are indicated on a

label on the top of the transformer.

5 On the ballast, move the BROWN wire to the terminal listed for the voltage. The

terminals are indicated on the top of the ballast.

6 Replace the cover.

Local AC Supply Transformer Ballast

Freq. Voltage Setting Terminal Setting / Terminal

50 Hz 220 - 235 V 225 V 3 230 V

50 Hz 235 - 245 V 240 V 4 240 V

50 Hz 245 - 260 V 240 V 4 250 V

Transformer

Ballast

225 V

240 V

230 V

240 V

250 V

0 V

AC power 9

US model

1 Disconnect the fixture from AC power.

2 If the lamp is hot, allow it to cool for 5 minutes and wear safety goggles to protect

your eyes.

3 Remove the 6 cover-access screws and lift of the fixture cover.

4Ontheballast, move the BLUE wire to the 225 V / 50 Hz terminal for 50 Hz local

AC supply, or to the 225 V / 60 Hz terminal for 60 Hz local AC supply.

5 On the transformer, move the BROWN wire to the setting as listed in the previous

table for the local AC voltage. The terminals are indicated on a label on the top of

the transformer.

6 Replace the cover.

Local

AC Voltage

Transformer

taps

95 - 110 V Blue wire: 20V

Brown wire: 120 V

110 - 130 V Blue wire: 0 V

Brown wire: 120 V

200 - 220 V Blue wire: 20 V

Brown wire: 230 V

220 - 240 V Blue wire: 0 V

Brown wire: 230 V

240 - 260 V Blue wire: 0 V

Brown wire: 250 V

Transformer Ballast

225 V / 60 Hz

225 V / 50 Hz

250 V

230 V

120 V

20 V

0 V

10 Wizard user manual

NSTALLATION

The Wizard can be hung overhead with a clamp (not included), mounted

vertically on a wall, or placed on the floor (using the optional floor stand).

Warning! Block access below the work area before proceeding. Always

use a secure means of secondary attachment.

WALL MOUNTING

To mount the Wizard on a wall, or other vertical surface:

1 Verify that the surface is capable of bearing the weight of the fixture.

2 Set two 8mm-diameter hex bolts or screws, 155 mm (6.1 in.) apart (center to

center), in the mounting surface.

3 Set an eye bolt in the mounting surface for the

safety cable.

4 Fold the mounting bracket so that it lies flat

against the back of the fixture and tighten the

swivel locks. We recommend that you remove

the swivel locks and replace them with M8

hexagonal lock nuts (2 x P/N 08132701);

alternatively set the swivel locks so that they lie

flat against fixture.

5 Hang the fixture on the wall over the two

screw/bolt heads using the two slotted holes in the mounting bracket.

6 Install a safety cable that can hold at least 10 times the weight of the fixture through

the safety cable eye on the fixture and attach this to the eye bolt.

7 Verify that the fixture is at least 0.1 meters (4 in.) from the surface to be illuminated

and at least 0.3 meters (12 in.) from any combustible materials. Verify that the

clearance around the air vents is at least 0.1 meters (4 in.).

max 13mm / ½"

Ø8mm

Indice

Altri manuali Martin Apparecchio di illuminazione

Martin

Martin MAC 250 Beam Manuale utente

Martin

Martin MAC 550 Profile Manuale utente

Martin

Martin MAC 401 Dual Manuale utente

Martin

Martin Easypix Manuale utente

Martin

Martin RoboColor Pro 400 Manuale utente

Martin

Martin MAC III PERFORMANCE Manuale utente

Martin

Martin MAC Viper AirFX Manuale utente

Martin

Martin MAC Encore Performance Manuale utente

Martin

Martin Exterior 1200 Wash Manuale utente

Martin

Martin MAC Viper Wash Manuale utente

Martin

Martin MAC 2000 Wash XB Manuale utente

Martin

Martin MAC Quantum Wash Guida all'installazione

Martin

Martin MAC 2000 Wash XB Manuale utente

Martin

Martin MAC 550 Profile Manuale utente

Martin

Martin JEM ZR44 Hi-MASS Manuale utente

Martin

Martin MAC 301 Manuale utente

Martin

Martin CYCLO 04 DMX Manuale utente

Martin

Martin ERA 300 Profile Manuale utente

Martin

Martin EFX500 Manuale utente

Martin

Martin MAC 250 Krypton Manuale utente

Martin

Martin JEM ZR series Manuale utente

Martin

Martin Raptor Manuale utente

Martin

Martin smartMAC Manuale utente

Martin

Martin MH 1 Profile Manuale utente

Manuali Apparecchio di illuminazione popolari di altre marche

Emos

Emos CLASSIC ZY1431T Manuale utente

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuale utente

Hedler

Hedler C 12 silent Manuale utente

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuale utente

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuale utente

Lightmaxx

Lightmaxx Shaft 5R Manuale utente

Triarch

Triarch 31083 Manuale utente

Philips

Philips 32614 Series Manuale utente

IKEA

IKEA TIVED Manuale utente

Lightolier

Lightolier LP200 Manuale utente

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuale utente

Cooper Lighting

Cooper Lighting Halo L3232E Manuale utente

Stageline

Stageline ODW-2410RGBW Manuale utente

Light Sky

Light Sky Tornado Series Manuale utente

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manuale utente

Lightolier

Lightolier Lytespan 83ED17S Manuale utente

Lightolier

Lightolier Calculite CS8226 Manuale utente

ArtFox

ArtFox Beam 15R extreme Manuale utente