6
OPERATING INSTRUCTIONS
CLEANING & MAINTENANCE
7
TROUBLESHOOTING
TM
1. Please note, if a power failure occurs due to disconnection of the power cord, or the power
button has been pushed off during an ice making cycle, small ice chips may form and lodge in the
automatic shovel causing it to jam. If this occurs, the ice chips may be removed by disconnecting
the power cord and gently pushing the shovel to the rear of the cabinet and removing the ice chips,
then restarting.
2. Please check if the water reservoir is level when the ice shovel cannot move the ice to the ice
basket. If not, please push the ice shovel gently by finger, then press POWER button to restart.
Step 1
Open the lid and add water to the reservoir.
Note: There is a MAX level in the reservoir. The water should not exceed the MAX level. If the
water exceeds the MAX level, you need to open the bottom drain plug to release the excess
water. Replace transparent lid.
Step 2
Plug in the power, and press the POWER button to start the machine.
Step 3
Select the size of the ice you want to make. NOTE: The default is large ice.
Note:
1. When the indoor temperature is below 20°C (68°F), choose small ice. Large ice is recom-
mended for indoor temperatures above 25°C (77°F).
2. When the cycles are used for the first time, the ice produced will be small and irregular.
3. When the ice basket is full, remove the ice immediately, do not let the ice overflow
the ice basket.
1. Clean the inner liner, ice collecting tray, water reservoir, ice shovel and evaporator frequently.
When cleaning, unplug the unit and remove the ice cubes. Use a diluted solution of water and
vinegar to clean the inside and the outside surface of the ice maker. Do not spray ice maker with
chemicals or diluted agents such as acids, gasoline or oil. Rinse thoroughly before starting.
2. Keep ventilation openings in the appliance enclosure, or in the built-in structure, clear of
obstruction. Do not use mechanical devices or other means to accelerate the defrosting process,
other than those recommended by the manufacturer.
3. When using the machine aer being idled for a period of time, it may not have enough water to
pump for air retard, and the indicator of “ADD WATER” will keep lighting. At this time, you just
need to press the POWER button again and the machine will enter normal state.
4. To ensure the cleanliness of ice, please change the water in water reservoir at least once per
day. If the ice maker has not been used in a long time, drain any water out and clean.
5. If the compressor does not work due to water shortage, ice is too full, power failure, and other
reasons, when the machine is started again, the compressor will delay 3 minutes before starting.
6. Please use pure water, mineral water is recommended, when making ice and aer long periods
of no use.
PROBLEM POSSIBLE CAUSE SUGGESTED SOLUTIONS
The compressor works
abnormally with a buzzing
noise.
The voltage is lower than
recommended.
Stop the ice maker and do
not restart until the voltage
is normal.
Water shortage indicator
light is on.
1. There is no water.
2. The pump is full of air.
1. Add some water until it
reaches MAX position.
2. Press POWER button to
restart.
The ice making procedure
is correct, but there is no
ice coming out.
1. The compressor has no
refrigerant.
2. Compressor damage.
3. The fan motor is damaged.
Call the service hotline.
The ice made is too large
and pieces are sticking
together.
1. The incorrect ice cube
size was chosen.
2. Ice from previous cycles
le in water reservoir.
1. Select small size.
2. Remove the ice when in the
standby mode.
Indicator lights on display
are not on. Blown fuse/ No power. Replace fuse / Turn power on.
All indicators flash
simultaneously.
1. The water reservoir is blocked
by ice.
2. The motor is stuck, or the
motor is off, or the motor is
damaged.
3. Micro switch damage.
1. Unplug the power and remove
the ice blocking the tray. Plug
power in and press the power
button; ice maker will restart in
3 minutes.
The machine is always
working, but the water is
always warm.
The solenoid valve has failed. Replace the solenoid valve.
When the ice basket is full,
the machine does not
prompt ICE FULL.
1. Ice full sensor damaged.
2. Solar ray interference.
1. Replace the red ice full sensor.
2. Move indoors to make ice.
3. Call the service hotline.
Product no. 043-2372-0/ICM305-WHITE | Contact us: 1-855-803-9313
