MasterCraft 068-0667-4 Manuale utente
continuation tabs
IMPORTANT:
Please read this manual carefully before assembling
and using this cabinet and save it for reference.
INSTRUCTION
MANUAL
EXTRA-WIDE TALL STORAGE CABINET
Model no. 068-0667-4
headline bars
continuation tabs
notes
warnings
headline bars
continuation tabs
notes
warnings
model no. 062-3582-8 | contact us 1-800-689-9928
TABLE OF CONTENTS
1
TABLE OF CONTENTS
TABLE OF CONTENTS
2
3
4
7
Safety
Parts List
Assembly Instructions
Warranty
SAVE THESE INSTRUCTIONS
This manual contains important safety and operating instructions.
Read all instructions and follow them with use of this product.
NOTE:
If any parts are missing or damaged, or if you have any questions,
please call our toll-free helpline at 1-800-689-9928.
2
headline bars
continuation tabs
notes
warnings
headline bars
continuation tabs
notes
warnings
model no. 068-0667-4 | contact us 1-800-689-9928
SAFETY
headline bars
continuation tabs
notes
warnings
headline bars
continuation tabs
notes
warnings
model no. 062-3582-8 | contact us 1-800-689-9928
• To reduce the risk of serious injury, read the following safety
instructions before assembling and using the cabinet.
• This cabinet is intended for domestic, indoor use only.
• The cabinet should be positioned on a level surface.
• Any assembly or maintenance of the cabinet must be carried
out by adults only.
• Arrange for necessary manpower when assembling and moving
the cabinet.
• Check all the nuts and bolts periodically for tightness.
When required, tighten them again.
• Use a slightly damp, soft cloth to clean the cabinet.
• Do not stand on the cabinet and do not use it as a scaffold.
• Do not exceed the weight limit specified for this cabinet.
Maximum each shelf load: 300 lb (136 kg).
Maximum bottom panel load: 400 lb (182 kg).
Maximum cabinet load: 1300 lb (590 kg).
SAVE THESE INSTRUCTIONS
This manual contains important safety and operating instructions.
Read all instructions and follow them with use of this product.
3
PARTS LIST
PARTS LIST
No.
1
2
3
4
5
6
7
8
9
No.
10
13
14
15
16
18
19
20
21
22
23
24
25
Description
Bottom back panel
Hook
Bumper
Corner protector A
Corner protector B
M4 x 18L screw
M4 x 8L screw
M4 x 30L screw
Screwdriver
Key
Magnet
Levelling foot
Wrench
Description
Left side panel
Right side panel
Top panel
Bottom panel
Middle shelf
Left door
Right door
Upper back panel
Middle back panel
Qty.
1
1
1
1
3
1
1
1
2
Qty.
1
12
4
2
2
16
97
6
1
2
2
4
1
4
headline bars
continuation tabs
notes
warnings
headline bars
continuation tabs
notes
warnings
model no. 068-0667-4 | contact us 1-800-689-9928
headline bars
continuation tabs
notes
warnings
headline bars
continuation tabs
notes
warnings
model no. 062-3582-8 | contact us 1-800-689-9928
ASSEMBLY INSTRUCTIONS
ASSEMBLY PREPARATION
• Assemble the storage cabinet on a clean, level surface.
• Remove all items from the packaging box and ensure that all parts listed on page
3 are included.
• When installing parts that have more than one screw, tighten all screws by hand
before tightening them with the screwdriver provided.
ASSEMBLY INSTRUCTIONS
1. Attach the left side panel (Part 1)
and right side panel (Part 2) to the top
panel (Part 3) by securing three M4 x
8 screws (Part 19) on each side of
the top panel. Tighten the screws
using the screwdriver (Part 21) (see
Fig. A).
Note: Make sure the front part of the cabinet
frame is facing down.
Note: As the cabinet frame is assembled
upside down, use carpet or blanket while
assembling the cabinet so that cabinet front
does not get scratched.
2. Attach the bottom panel (Part 4) to
the left side panel (Part 1) and right
side panel (Part 2) by securing three
M4 x 30 screws (Part 20) on each
side of the bottom panel. Tighten the
screws using the screwdriver (Part
21) (see Fig. B).
Fig. A
Fig. B
5
ASSEMBLY INSTRUCTIONS
3. Attach the bottom back panel (Part
10), middle back panels (Part 9) and top
back panel (Part 8) to the assembled
cabinet frame. Starting from the bottom
back panel, insert a total of 41 tM4 x 8
screws (Part 19) into the screw holes of
all the back panels and tighten them
using the screwdriver (Part 21) (see Fig.
C).
Note:
Two screw holes for corner protectors are
reserved across the top panel and the bottom panel.
4. Attach the levelling feet (Part 24) to
the four corners of the bottom panel (Part
4) using the wrench (Part 25) (see Fig. D).
5. Turn the cabinet frame to upright
position.
6. Choose desired height for placing
each middle shelf (Part 5) inside the
cabinet frame. Then pull down the hooks
(Part 13) into the hook slots provided,
making sure the four hooks are placed at
the same height. Place the shelves into
the cabinet frame and press them down
onto the hooks (see Fig. E).
7. Attach one of two magnets (Part 23) to
the top panel (Part 3) and another magnet
to the bottom panel (Part 4). Insert two
M4 x 8 screws (Part 19) into each
magnet and tighten them using the
screwdriver (part 21) (see Fig. F).
Note: The black plate of the magnet
(Part 23) should be facing the front.
Fig. F
Fig. E
Fig. D
Fig. C
6
headline bars
continuation tabs
notes
warnings
headline bars
continuation tabs
notes
warnings
model no. 068-0667-4 | contact us 1-800-689-9928
headline bars
continuation tabs
notes
warnings
headline bars
continuation tabs
notes
warnings
model no. 062-3582-8 | contact us 1-800-689-9928
ASSEMBLY INSTRUCTIONS
8. Attach the left door (Part 6) and
right door (Part 7) to corresponding
sides of the cabinet frame. Insert 10
M4 x 8 screws (Part 19) into each
door and tighten them using
screwdriver (Part 21) (see Fig. G).
9. Attach the bumpers (Part 14) to
the four corners of the bottom panel
by securing four M4 x 18 screws
(Part 18) for each bumper. Then
attach corners protectors A (Part 15)
and corner protectors B (Part 16) to
the four corners of the top panel
(Part 3) by securing five M4 x 8
screws (Part 19) on each corner
protector. Tighten the screws using
screwdriver (Part 21) (see Fig. H).
10. The storage cabinet is ready to
be used. Use the keys (Part 22) to
lock the left door (Part 6) and right
door (Part 7) of the cabinet, if desired
(see Fig. I).
Note: This product provides fingerprint-re-
sistant surfaces and increased durability.
Stainless Steel Maintenance:
A fingerprint-resistant finish has been applied to these parts. Do not use traditional
stainless steel cleaners on this unit. Lightly wipe off once a month with clean warm
water and a soft cloth (preferably a microfibre cloth). This is the safest formula to
prevent new stains from appearing over time and manage unwanted fingerprints or
grease marks. Remember to always wipe in the direction of the surface grain
(NEVER ACROSS) and always use a lint-free cloth. Once the surface is clean,
thoroughly wipe dry with a soft absorbent cloth.
Fig. G
Fig. H
Fig. I
7
WARRANTY
This Mastercraft® product carries a one (1) year warranty from the date of the original
retail purchase, against defects in material and workmanship. Subject to the condi-
tions and limitations described below, this product, if returned to us with proof of
purchase within the stated warranty period and if covered under this warranty, will be
repaired or replaced (with the same model, or one of equal value or specification), at
our discretion. We will bear the cost of any repair or replacement and any costs of
labour relating thereto.
This warranty is subject to the following conditions and limitations:
a. a bill of sale verifying the purchase and purchase date must be provided;
b. this warranty will not apply to any product or part thereof which is worn or broken
or which has become inoperative due to abuse, misuse, accidental damage, neglect or
lack of proper installation, operation or maintenance (as outlined in the applicable
owner's manual or operating instructions) or which is being used for industrial, profes-
sional, commercial or rental purposes;
c. this warranty will not apply to normal wear and tear or to expendable parts or acces-
sories that may be supplied with the product which are expected to become inopera-
tive or unusable after a reasonable period of use;
d. this warranty will not apply to routine maintenance and consumable items such as,
but not limited to, fuel, lubricants, vacuum bags, blades, belts, sandpaper, bits, fluids,
tune-ups or adjustments;
e. this warranty will not apply where damage is caused by repairs made or attempted
by others (i.e., persons not authorized by the manufacturer);
f. this warranty will not apply to any product that was sold to the original purchaser as
a reconditioned or refurbished product (unless otherwise specified in writing);
g. this warranty will not apply to any product or part thereof if any part from another
manufacturer is installed therein or any repairs or alterations have been made or
attempted by unauthorized persons;
h. this warranty will not apply to normal deterioration of the exterior finish, such as, but
not limited to, scratches, dents, paint chips, or to any corrosion or discolouring by heat,
abrasive and chemical cleaners; and
i. this warranty will not apply to component parts sold by and identified as the product
of another company, which shall be covered under the product manufacturer's
warranty, if any.
Additional Limitations
This warranty applies only to the original purchaser and may not be
transferred. Neither the retailer not the manufacturer shall be liable for
any other expense, loss or damage, including, without limitation, any
indirect, incidental, consequential or exemplary damages arising in
connection with the sale, use or inability to use this product.
Notice to Consumer
This warranty gives you specific legal rights, and you may have other
rights, which may vary from province to province. The provisions
contained in this warranty are not intended to limit, modify, take away
from, disclaim or exclude any statutory warranties set forth in any applica-
ble provincial or federal legislation.
Made in China
Imported by
Mastercraft Canada Toronto, Canada M4S 2B8
headline bars
continuation tabs
notes
warnings
Indice
Lingue:
Altri manuali MasterCraft Magazzinaggio
