MasterCraft 062-3413-2 Manuale utente

INSTRUCTION

MANUAL

Stainless Steel

IRRIGATION AND

LAWN SPRINKLER PUMP

IMPORTANT:

Please read this manual carefully before running

this pump and save it for reference.

model no. 062-3413-2

Technical Speciﬁcations 4

Safety 5

Installation Instructions 7

Operation Instructions 9

Troubleshooting 11

Key Parts Diagram 12

Warranty 13

TABLE OF CONTENTS

NOTE:

If any parts are missing or damaged, or if you have any questions, please call our

toll-free helpline at 1-800-689-9928.

SAVE THESE INSTRUCTIONS

This manual contains important safety and operating instructions.

Read all instructions and follow them with use of this product.

model no. 062-3413-2 | contact us 1-800-689-9928

Model number 062-3413-2

Voltage 115 V/60 Hz

Maximum head height 165' (50 m)

Horsepower 1 1/2 HP

Amps 10 A

Maximum ﬂow 1200 U.S. GPH (4542 L/h)

Discharge size 1" (2.5 cm) female national pipe thread (FNPT),

¾" (1.9 cm) garden hose adaptor (included)

Power cord length 6’ 7” (2 m)

TECHNICAL SPECIFICATIONS

0' (0 m) 50' (15.2 m) 100' (30.5 m) 150' (45.7 m)

1200 U.S. GPH

(4542 L/h)

900 U.S. GPH

(3407 L/h)

480 U.S. GPH

(1817 L/h)

40 U.S. GPH

(151 L/h)

PERFORMANCE

TECHNICAL SPECIFICATIONS

SAFETY

Please read and understand this entire manual before attempting to assemble, operate or install

the product. If you have any questions regarding the product, please call customer service at

1-800-689-9928.

WARNING

• Running the pump without sufﬁcient water will damage the pump and void the pump's

warranty.

• Do not pump ﬂammable or explosive liquids such as oil gasoline kerosene ethanol, etc. Do not

use in the presence of ﬂammable or explosive vapours. Using this pump with or near

ﬂammable liquids can cause an explosion or ﬁre, resulting in property damage, serious

personal injury and/or death.

• Always disconnect the pump from its power source before inspection.

• Do not stand in water when the pump is connected. Do not handle pump with wet hands.

• Do not touch the pump housing while it is operating as the pump may be HOT and can cause

serious skin burns.

• Do not disassemble the motor housing. This pump has NO repairable internal parts, and

disassembling may cause dangerous electrical wiring issues.

CAUTION:

• This pump is made of high-strength corrosion-resistant materials. It will provide

trouble-free service for many years when properly installed, maintained, and used.

However, inadequate electrical power or blockage by dirt could cause damage to the pump

and void the warranty. To minimize the potential for water damage due to pump failure

please read the section of this manual regarding common pump problems and remedies or

call one of our pump experts at 1-800-689-9928.

• This pump is not designed to function as a permanently installed pump. It is also not

engineered to be run continuously as a "fountain" or "waterfall" pump. The pump should

be used with a 5/8" (1.6 cm) or larger inside diameter garden hose.

• For safety, the pump motor has an automatically resetting thermal protector that

automatically will turn off the pump if it becomes too hot. Overuse of this feature will

damage the pump and void the warranty.

• Once the thermal protector detects that the pump has cooled to a safe temperature, it will

allow the pump to operate normally. If the pump is plugged in, it may restart unexpectedly.

model no. 062-3413-2 | contact us 1-800-689-9928

SAFETY

ADDITIONAL SAFETY PRECAUTIONS

1. Know the pump applications, limitations, and potential hazards.

2. Make certain the electrical power source is adequate for the requirements of the pump.

3. ALWAYS disconnect the power to the pump and drain all water from the system before

servicing.

4. Secure the pump on a solid base as close to the source of water as possible.

5. Secure the discharge hose before starting the pump. Pump torque may cause an unsecured

discharge hose to "whip”, possibly causing personal injury and/or property damage.

6. Before using the pump, check the hose for holes or excess wear, which could cause leaks, and

ensure the hose is not kinked or making sharp angles. A straight hose allows the pump to

move the greatest amount of water quickly.

7. Check that all hose connections are tight to minimize leaks.

8. Connect the pump directly to a grounded GFCI outlet.

9. Extension cords may not deliver sufﬁcient voltage to the pump motor. Extension cords present

a life-threatening safety hazard if the insulation becomes damaged or the connection ends fall

into the water. If using a 50' (15 m) cord, use 16-gauge wire. If using a 100' (30 m) cord, use

14-gauge wire.

10. Make certain the electrical circuit to the pump is protected by a 10 A or larger fuse or circuit

breaker.

11. Periodically inspect pump and system components to ensure that the pump inlets are free of

mud, sand, and debris. DISCONNECT THE PUMP FROM THE POWER SUPPLY BEFORE

INSPECTING.

12. Wear safety glasses at all times when working with pumps.

13. Follow all electrical and safety codes, particularly the National Electrical Code (NEC) or the

Canadian Electrical Code (CEC), and in the workplace, the Occupational Safety and Health Act

(OSHA) or the Canadian Centre for Occupational Health and Safety (CCOHS).

14. This unit is designed only for use on 115 V (single phase), 60 Hz, and is equipped with an

approved 3-conductor cord and 3-prong, grounding-type receptacle. Do not use the pump

with a 2-prong wall outlet. Replace the 2-prong outlet with a properly grounded 3-prong

receptacle (a GFCI outlet) installed in accordance with the NEC or CEC and local codes and

ordinances. AII wiring should be performed by a qualiﬁed electrician.

15. Protect the electrical cord from sharp objects, hot surfaces, oil, and chemicals. Avoid kinking

the cord. Do not use damaged or worn cords.

INSTALLATION INSTRUCTIONS

Estimated Assembly Time: 5 minutes

Materials Required for Assembly (sold separately): 3/4" (1.9 cm) foot valve, 1" (2.5 cm) discharge tee,

100# pressure gauge, thread tape, 3/4" (1.9 cm) standard garden hose (for discharge), 3/4" (1.9 cm)

heavy-duty garden hose (for suction).

NOTE:

• If a standard garden hose is used for suction line, the hose could collapse, allowing the pump to run dry.

This could cause permanent damage and void warranty. This pump is designed to sprinkle lawns and

small gardens from lakes, ponds, or rivers, empty or ﬁll stock tanks, remove standing water from ﬂooded

areas or transfer water. Flammable liquids such as gasoline, chemicals, or corrosive liquids should never

be used with this pump.

• This pump is not intended for permanent installation or long, extended periods of continuous operation.

• This pump is not to be used with pop-up sprinklers.

CAUTION:

• Never install a shutoff valve in the suction or discharge of this pump. This will cause

excessive friction loss and will damage the pump and void the warranty.

• AII connections must be airtight. A single leak will prevent proper operation of the pump

and may cause the pump to run dry. If the pump runs dry, this will void the warranty.

WARNING:

• Always use the handle to lift pump. Never use a power cord to lift pump. To avoid skin

burns, unplug and allow time for the pump to cool after periods of extended use. Before

beginning assembly of the product, make sure all parts are present. Compare parts with

package contents list. If any part is missing or damaged do not attempt to assemble the

product. Contact customer service for replacement parts.

• Place the pump on level support before operation.

1Positioning the Pump

a. Place the pump as close as possible to the water

source, keeping the vertical distance from the

water to the pump as small as possible

(maximum lift is 25' (7.6 m)).

b. Place the pump (A) on a level support.

c. Install a 3/4" (1.9 cm) foot valve (sold

separately). When the suction lift is over 10'

(3 m) or when the suction line is more than 10'

(3 m) long, the foot valve will keep the pump

primed when it is turned off.

d. You can use a regular garden hose (sold

separately) as the discharge line.

Note: The inlet line may be PVC or reinforced hose.

Small leaks in the suction line greatly reduce the

efﬁciency of the pump and may prevent priming.

model no. 062-3413-2 | contact us 1-800-689-9928

INSTALLATION INSTRUCTIONS

2Positioning the Hose Adaptors

a. Wrap threads of discharge tee (sold

separately) with thread tape.

b. Thread a 1" (2.5 cm) discharge tee

(2) into the outlet of the pump.

c. Thread hose adaptors (B) into pump

outlet and into the discharge tee (2).

Note: Discharge tee is optional.

CAUTION: A|I connections must be

airtight. A single leak will prevent proper

operation of the pump and may cause

the pump to run dry. This will void the

warranty.

Installing the Pump:

a. Connect a 3/4" (1.9 cm) heavy-duty garden

hose (sold separately) to the pump inlet (1).

The inlet connection can also be used with 1"

(2.5 cm) PVC pipe (Note: If you are using a PVC

pipe, you will need a 1" (2.5 cm) male NPT X

slip adaptor).

Notice: The inlet hose must be a reinforced type

when pumping from lakes, ponds, or small

streams. A regular garden hose will collapse and

lead to pump failure.

Note: A foot valve MUST be used to maintain

prime during operation. Foot valves are sold

separately.

b. Connect an outlet pipe or 3/4" (1.9 cm)

standard garden hose (sold separately) to the

discharge tee (2). The outlet connection is

designed for a 1" (2.5 cm) NPT thread. Rigid

pipes such as PVC or a garden hose may be

used.

Connect your discharge hose to a

standard lawn sprinkler (maximum

2 sprinklers).

Note: This pump (A) is not designed to

be used with underground, pop-up

sprinklers (zoned systems). If you have

this type of system, purchase a

higher-capacity lawn or irrigation pump.

OPERATION INSTRUCTIONS

1Priming the Pump:

Note:

• The pump must be ﬁlled with water before

operation. Running the pump dry will cause

damage to the shaft seal and will void the

warranty.

• Add thread tape on the discharge tee cap

(2). If discharge tee is not connected:

Remove the discharge tee cap (2). Fill water

into top of discharge tee (3) until pump

overﬂows with water. If discharge tee is

connected, remove the prime plug (1). Fill

water into top of discharge tee (3) until

pump overﬂows with water. Reinstall the

prime plug (1) or the discharge tee cap (2)

when ﬁnished priming.

• This pump is not designed to be used with

under-ground pop-up sprinklers (zoned

systems). If you have this type of system

purchase a higher-capacity lawn or

irrigation pump.

Usage: You can install a 100# pressure gauge

(sold separately) on top of the discharge tee

cap in order to monitor pressure.

WARNING:

• Do not run the pump with the outlet pipe or hose nozzle closed. This will cause damage to

the pump, or burst the hose from excessive pressure. This could result in death or serious

injury. Use only reinforced high-pressure hoses or pipes for the outlet connection or pipes

for the inlet (suction) connection.

• Never remove the ground prong on the power cord. Never hardwire the power cord.

Cutting the cord, hardwiring, or removing the ground prong can result in death or serious

injury and will void the warranty.

model no. 062-3413-2 | contact us 1-800-689-9928

OPERATION INSTRUCTIONS

3Storing the Pump:

Protect against ﬂooding and

excessive moisture by storing in a

dry place.

Draining the Pump for Winter:

a. Disconnect the suction (1) and

discharge (2) lines from the

pump (A).

b. Remove the water drain plug (3)

from the pump (A).

c. Drain all piping below the frost

line or store the piping indoors.

d. Store the pump indoors.

Running the Pump

Plug the power cord into a GFCI-protected

electrical outlet and press the power switch

to the On position. If the pump does not

pump water within 2 minutes, turn the pump

(A) off. Reﬁll with clean water and make sure

all connections are airtight. To turn the pump

off, press the power switch to the off

position.

DANGER: Risk of electric shock. Always

disconnect the electrical supply before

attempting to install, service, or perform any

maintenance. If the power source is out of

sight, lock and tag in the open (off) position

to prevent unexpected power application.

Failure to do so could result in fatal electrical

shock. Only qualiﬁed electricians should

repair this unit. Improper repair could result

in fatal electric shock.

WARNING: Let the pump cool for at least 20

minutes before attempting to service. The

motor may be extremely hot. Personal injury

may result.

Indice

Altri manuali MasterCraft Pompa dell'acqua

MasterCraft

MasterCraft 62-3515-0 Manuale utente

MasterCraft

MasterCraft 062-3593-2 Manuale utente

MasterCraft

MasterCraft 062-3425-4 Manuale utente

MasterCraft

MasterCraft 62-3518-4 Manuale utente

MasterCraft

MasterCraft 62-3527-2 Manuale utente

MasterCraft

MasterCraft 62-3569-2 Manuale utente

MasterCraft

MasterCraft 062-3404-4 Manuale utente

MasterCraft

MasterCraft 62-3577-2 Manuale utente

MasterCraft

MasterCraft 62-3564-2 Manuale utente

MasterCraft

MasterCraft 062-3420-4 Manuale utente

MasterCraft

MasterCraft F12V-CTC Manuale utente

MasterCraft

MasterCraft 312222 Manuale utente

MasterCraft

MasterCraft 062-3429-6 Manuale utente

MasterCraft

MasterCraft 312222-01 Manuale utente

MasterCraft

MasterCraft 62-3510-0 Manuale utente

MasterCraft

MasterCraft 062-3428-8 Manuale utente

MasterCraft

MasterCraft 062-3422-0 Manuale utente

MasterCraft

MasterCraft 062-3538-6 Manuale utente

MasterCraft

MasterCraft 062-3503-8 Manuale utente

MasterCraft

MasterCraft 62-3523-0 Manuale utente

MasterCraft

MasterCraft 062-3579-8 Manuale utente

MasterCraft

MasterCraft 062-3415-8 Manuale utente

MasterCraft

MasterCraft 062-3406-0 Manuale utente

MasterCraft

MasterCraft 062-3408-6 Manuale utente

Manuali Pompa dell'acqua popolari di altre marche

Neptun

Neptun NPHW 5500 Manuale utente

Sensidyne

Sensidyne Gilian BDX-II Istruzioni per l'installazione e il funzionamento

Draper

Draper 47808 Manuale utente

Trolla

Trolla 12820 Manuale utente

Sunfab

Sunfab SVH Series Manuale utente

WilTec

WilTec 50740 Manuale utente

Fieldmann

Fieldmann FVC 5015 EK Manuale utente

Everbilt

Everbilt EFSUB5-122HD Manuale utente

Graco

Graco Husky 3300e Manuale utente

esotec

esotec 101018 Manuale utente

moyno

moyno 2000 CC Manuale utente

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuale utente

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guida alla risoluzione dei problemi

DUROMAX

DUROMAX XP WX Series Manuale utente

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuale utente

Franklin Electric

Franklin Electric IPS Manuale utente

Xylem

Xylem e-1532 Series Manuale utente

Milton Roy

Milton Roy PRIMEROYAL Manuale utente