MasterForce 241-0828 Manuale utente

OPERATING MANUAL

Planer

241-0828

IMPORTANT :

Carefully read this Owner’s Manual before using this tool. Pay close atten-

tion to all Safety Instructions, Warnings, and Caution sections. Use this tool

properly, and only for its intended use.

Safety symbols in this manual are used to ﬂag possible dangers. The safety

symbols and their explanations require the operator’s full understanding. The

safety warnings do not, by themselves, eliminate any danger, and they are not

a substitute for proper accident prevention measures.

This Safety Alert Symbol indicates caution, warning, or danger. Failure to

obey a safety warning can result in serious injury to yourself or others. To reduce

the risk of injury, ﬁre, or electric shock, always follow the safety precautions.

TABLE OF CONTENTS

Speciﬁcations................................................................................................. Page 2

Rules for Safe Operation ..............................................................................Page 3

Assembly and adjustment ............................................................................ Page 7

Operation......................................................................................................... Page 10

Accessories .................................................................................................... Page 13

Maintenance................................................................................................... Page 13

Warranty.......................................................................................................... Page 14

SPECIFICATIONS

Motor 120V 60Hz 6.0A

Single Speed 17, 000 RPM

Depth of cut range 0 to 5/64”

Width of cut: 3-1/4”

Weight: 7 LB 1 oz (3.2Kg)

SAFETY SYMBOLS FOR YOUR TOOL

The label on your tool may include the following symbols.

V...............................................................Volts

A...............................................................Amps

Hz.............................................................Hertz

W..............................................................Watts

min...........................................................Minutes

...........................................................Alternating Current

............................................................Direct Current

no...........................................................No-load Speed

............................................................Class II construction

.../min.......................................................Revolutions or Strokes per minute

....................................................Indicates danger, warning caution. It means

attention! Your safety is involved.

RULES FOR SAFE OPERATION

KNOW THE TOOL

Read this operating manual and all the labels afﬁxed to the angle grinder

carefully before using this tool. Keep this manual available for future

reference.

IMPORTANT

This tool should only be serviced by a qualiﬁed service technician.

READ ALL INSTRUCTIONS THOROUGHLY

GENERAL SAFETY RULES FOR ALL POWER TOOLS

WARNING!Read and understand all instructions. Failure to follow all in-

structions listed below may result in electric shock, ﬁre and/or serious per-

sonal injury.

SAVE THESE INSTRUCTIONS

Work Area

Keep your work area clean and well lit. Cluttered benches and dark

areas invite accidents.

Do not operate power tools in explosive envirnments, such as in the

presence of ﬂammable liquids, gases, or dust. Power tools create sparks

which may ignite the dust or fumes.

Keep bystanders, children, and visitors away while operating a power

tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

Double insulated tools are equipped with a polarized plug (one blade

is wider than the other.) This plug will ﬁt in a polarized outlet only one

way. If the plug does not ﬁt fully in the outlet, reverse the plug. If it

still does not ﬁt, contact a qualiﬁed electrician

to install a polarized outlet. Do not change the

plug in any way. Double insulation eliminates

the need for the three wire grounded power cord

and grounded power supply system.

Avoid body contact with grounded surfaces such

as pipes, radiators, ranges and refrigerators.

There is an increased risk of electric shock if your

body is grounded.

120V ~ 60Hz

Don’t expose power tools to rain or wet conditions. Water entering a

power tool will increase the risk of electric shock.

Do not abuse the cord. Never use the cord to carry the tools or pull

the plug from an outlet. Keep cord away from heat, oil, sharp edges or

moving parts. Replace damaged cords immediately. Damaged cords

increase the risk of electric shock.

When operating a power tool outside, use an outdoor extension cord

marked “W-A” or “W”. These cords are rated for outdoor use and reduce

the risk of electric shock. The following table shows the correct size to

use, depending on cord length and nameplate amperage rating of the tool.

When in doubt, use the next heavier gauge. Always use UL and CSA listed

extension cords.

Recommended sizes of extension cords

Tool’s Ampere rating Volts

Total length of cord in feet

Cord size in A. W. G.(minimum)

25’ 50’ 100’ 150’

0-6

120

18 16 16 14

6-10 18 16 14 12

10-12 16 16 14 12

12-16 14 12 Not Recommended

Personal Safety

Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use tool while tired or under the inﬂuence

of drugs, alcohol, or medication. A moment of inattention while operating

power tools may result in serious personal injury.

Dress properly. Do not wear loose clothing or jewelry. Contain long hair.

Keep your hair, clothing, and gloves away from moving parts. Loose

clothes, jewelry, or long hair can be caught in moving parts.

Avoid accidental starting. Be sure switch is off before plugging in.

Carrying tools with your ﬁnger on the switch or plugging in tools that have

the switch on invites accidents.

Remove adjusting keys or wrenches before turning the tool on. A wrench

or a key that is left attached to a rotating part of the tool may result in

personal injury.

Do not overreach. Keep proper footing and balance at all times. Proper

footing and balance enables better control of the tool in unexpected

situations.

Use safety equipment. Always wear eye protection. Dust mask, non-skid

safety shoes, hard hat, or hearing protection must be used for appropriate

conditions.

Before connecting the tool to a power source (receptacle, outlet, etc.), be

sure voltage supplied is the same as that speciﬁed on the nameplate of

the tool. A power source with voltage greater than that speciﬁed for the

tool can result in serious injury to the user – as well as damage to the tool.

Tool Use and Care

Use clamps or other practical way to secure and support the workpiece

to a stable platform. Holding the work by hand or against your body is

unstable and may lead to loss of control.

Do not force tool. Use the correct tool for your application. The correct

tool will do the job better and safer at the rate for which is designed.

Do not use tool if switch does not turn it on or off. Any tool that cannot be

controlled with the switch is dangerous and must be repaired.

Disconnect the plug from the power source before making any

adjustments, changing accessories, or storing the tool. Such preventive

safety measures reduce the risk of starting the tool accidentally.

Store idle tools out of reach of children and other untrained persons.

Tools are dangerous in the hands of untrained users.

Maintain tools with care. Keep cutting tools sharp and clean. Properly

maintained tools, with sharp cutting edges are less likely to bind and are

easier to control.

Check for misalignment or binding of moving parts, breakage of parts,

and any other condition that may affect the tools operation. If damaged,

have the tool serviced before using. Many accidents are caused by poorly

maintained tools.

Use only accessories that are recommended by the manufacturer for

your model. Accessories that may be suitable for one tool, may become

hazardous when used on another tool.

Do not alter or misuse tool. These tools are precision built. Any alteration

or modiﬁcation not speciﬁed is misuse and may result in a dangerous

condition.

SERVICE

Tool service must be performed only by qualiﬁed repair personnel.

Service or maintenance performed by unqualiﬁed personnel could result

in a risk of injury.

When servicing a tool, use only identical replacement parts. Follow

instructions in the Maintenance section of this manual. Use of

unauthorized parts or failure to follow Maintenance Instructions may

create a risk of electric shock or injury.

SPECIFIC SAFETY RULES FOR PLANER

1. Hold tool by insulated gripping surfaces when performing an operation

where the cutting tool may contact hidden wiring or its own cord. Contact

with a “live” wire will make exposed metal parts of the tool “live” and

shock the operator.

2. Secure the material being planed. Never hold it in your hand or across

legs. A small workpiece must be adequately secured so that the rotating

planer blades will not pick it up during forward motion of the planer.

Unstable support can cause the blades to bind, causing loss of control and

injury.

3. Always start the planer before the blade is in contact with the workpiece

and allow the blade to come to full speed. The tool can vibrate or chatter

if the blade speed is too slow at the beginning of the cut and could possibly

kickback.

4. Check the workpiece for nails. If there are nails, either remove or set

them well below the intended ﬁnished surface. If the planer blades strike

objects like nails they may cause the tool to kickback, and serious personal

injury may result.

5. Never leave the trigger locked “ON”. Unplug the planer before changing

accessories. Before plugging the tool in, check that the trigger lock is

“OFF”. Accidental start-ups may occur if the planer is plugged in while

changing an accessory.

6. After changing blades, rotate the blade drum to make sure that blades

are not hitting any part of the blade-head housing and the blade-locking

screws are tight. Spinning blades could strike the tool housing and

damage the tool as well as possibly causing injury.

7. Always hold the tool ﬁrmly with both hands for maximum control.

8. Never pull the plane backward over the workpiece. Loss of control may

occur.

9. Do not put ﬁngers or any objects into the chip ejector or clean out chips

while the tool is running. Contact with the blade drum will cause injury.

10. Remove the plug from the power source if it becomes necessary to

remove chips. The blades are hidden from view and you may be cut if the

blade is contacted.

11. Never place the plane down until the blade is completely at rest.

Surface contact with a coasting blade drum may cause the plane to walk

out of control.

12. Never use dull or damaged blades. Sharp blades must be handled with

care. Damaged blades can snap during use. Dull blades require more

force to push the tool, possibly causing the blade to break.

13. Always wear safety goggles, respiration mask, and ear protection.

ASSEMBLY AND ADJUSTMENT

The planer is intended only for planing ﬁrmly supported wooden materials,

such as beams and boards. It is also suitable for beveling edges and

rabbeting.

KNOW YOUR PLANER

(See Fig. 1)

1. ON/OFF trigger switch

2. Lock-off button

3. Depth-adjustment knob

4. Back handle

5. Front handle

6. Dust/chip extraction port (x 2)

7. Edge-guide attachment knob

8. Dust/chip extraction guide switch

9. Reversible blades

Fig. 1

10. Blade barrel

11. Clamping screw

12. Adjustable front base

13. Fixed rear base

14. Edge guide

15. Bag adaptor

16. Dust bag

17. Wrench

18. Wrench storage sleeve

REMOVING OR INSTALLING PLANER BLADES

CAUTION: Always ensure that the tool is switched OFF and unplugged from

the power supply before installing or removing blades.

Your planer is ﬁtted with reversible blades. Blades can be reversed when

one edge has become blunt. After

both sides of the blades have been

used they should be discarded and

replaced with identical blades.

NOTE. These blades cannot be re-

sharpened.

REMOVING A PLANER BLADE

1. Using the wrench (17), loosen the

three clamping screws (11) (See

Fig. 2).

2. Slide the planer blade (9) from the

slot in the blade barrel (10)

(See Fig. 3).

INSTALLING A PLANER BLADE

(See Fig. 4)

1.Use the other edge of the

reversible planer blade (9), or, if

dull, replace the blade.

Fig. 3

Fig. 2

4. Slide the sharp blade face-up into

the blade-support block of the blade

barrel (10).

NOTE. The ridge along the blade

should be face away from the

clamping screws (11).

5. Evenly tighten the clamping screws

(11).

6. Repeat with the other blade.

NOTE: Always change the two blades at the same time, otherwise an

imbalance may occur and cause vibration and shorten the life of both the

blade and the tool.

NOTE: The blade position has been aligned at the manufactory, so do not

adjust the three inner hex screws on the blade supporter.

CAUTION: When installing blades, ﬁrst clean out all chips and/or foreign

matter adhering to the blade barrel (10) and the blades themselves. Use

blades of the same dimensions and weight, or else the barrel will oscillate

and vibrate, causing poor planing action and tool breakdown. Tighten the

clamping screws (11) carefully when attaching the blades to the planer. A

loose clamping screw could be extremely dangerous. Regularly check to

ensure that the clamping screws are securely tightened.

NOTE: Your planing surface will end up rough and uneven unless the blades

are set properly and securely. The blades must be mounted so that the

cutting edge is absolutely level: parallel to the surface of the rear base (13).

ADJUSTING THE DEPTH OF CUT (See Fig. 5)

CAUTION: Always ensure that the

tool is switched OFF and unplugged

from the power supply before making

adjustments or installing or removing

blades.

1. Rotate the depth-adjustment knob

(3) clockwise for a deeper cut

and counter-clockwise for a more

shallow cut.

2. The numbers on the ring under

the depth-adjustment knob indicate the depth of cut. For example, when

Fig. 4

Fig. 5

“2” is next to the pointer on the front of the planer, the depth of cut is

approximately 2 mm.

3. If it is necessary to accurately determine the depth of cut, plane a scrap

piece of wood, measure the difference in thickness, and adjust the setting.

CAUTION: Always ensure that the number on the ring is at the “0” position

when the tool is not in use; at this position, the blade cannot cut the

workpiece.

OPERATION

SWITCHING ON AND OFF (See Fig. 6)

CAUTION: Before plugging the

machine into the power supply,

always check that the trigger switch

(1) and lock-off button (2) are working

properly.

1. Plug in the tool, push in the lock-

off button (2), and pull the trigger

switch (1).

2. To stop the tool, simply release the

trigger switch (1).

3. In order to restart the tool, it is necessary to operate both the lock-off

button (2) and the trigger switch (1). This is an important safety feature that

helps prevent accidental operation of the planer.

PLANING

CAUTION: Always use two hands when holding the planer.

CAUTION: Wherever possible, clamp the workpiece to a workbench or

clamping table.

CAUTION: Moving the planer too quickly may cause a poor quality of cut and

can damage the blades or the motor. Moving the planer too slowly may burn

or mar the workpiece.

1. Rest the front base (12) ﬂat on the workpiece surface without the blades

making any contact with the workpiece.

2. Switch on the tool and wait for the blades to reach full speed.

Fig. 6

Indice

Altri manuali MasterForce Pialla

MasterForce

MasterForce 241-0824 Manuale utente

Manuali Pialla popolari di altre marche

Felisatti

Felisatti PF180/1500 Manuale utente

DeWalt

DeWalt DW 1150 Guida

Triton

Triton TRP UL Guida rapida

Melbourne

Melbourne MTC-49407 Manuale utente

VARO

VARO POWERplus POW1520 Manuale utente

Powermatic

Powermatic 209 Manuale di servizio

Skil

Skil 1565 Manuale utente

Makita

Makita 1051D Manuale utente

Scheppach

Scheppach Plana 3.0 Istruzioni per il montaggio

Grizzly

Grizzly G1033X Manuale utente

Stanley

Stanley STPP7502 Manuale utente

Palmgren

Palmgren 84115 Manuale utente

Draper

Draper PT610V Manuale utente

Makita

Makita PC5000C Manuale utente

Berner

Berner BP 40-82 C Manuale utente

Grizzly

Grizzly G0603X Manuale utente

King Industrial

King Industrial CT-381FX Manuale utente

FXA

FXA FXAJD8220 Manuale utente