Matchmaster 04MM-PRO1 Manuale utente
04MM-RP01, RP02 & RP03
INSTRUCTION MANUAL
WARNINGS AND CAUTIONS
IMPORTANT INSTRUCTIONS
SAFETY INSTRUCTIONS
HOW TO INSTALL IN NEW BUILDS
• To be installed by a suitably
qualied installer
• To be installed and/or used in
accordance with appropriate electrical
codes and regulations
• If you are unsure about any part of
these instructions, consult a
qualied installer
• Read and understand all instructions.
Follow all warnings and instructions
marked on the product
• Do not use this product near water - eg.
near a bathtub, wash basin, sink, a wet
basement or near a swimming pool
• Never push objects of any kind into this
product through openings, as they may
touch dangerous voltages
• Never install components during an
electrical storm
• Never install components in wet
locations unless the components are
designed for such use
• Never touch uninsulated wires or
terminals unless the wiring has been
disconnected at the network interface
Note: Wiring from existing power points
does not need to be disconnected but
must always be turned off at the
mains rst.
1. Warning: To avoid re, shock or
death, turn off the power at the circuit
breaker or fuse and test the power is
off before continuing.
2. Choose the location for the RP0x, the
installation requires mounting the RP0x
using oating clips mounted in each
corner, you will need to select a wall
location free from obstructions such
as timber frames, metal wall straps etc,
and please make sure there is no wall
point back to back if installing into an
internal wall location as this will affect
the available wall depth.
THIS IS A TEMPLATE FOR YOUR 04MM-RP01, RP02 & RP03 (168X120MM)
3. Cut out hole in wall sheeting using
template provided as a guide. Check
for obstructions in the wall cavity to
ensure the RP0x will t in its location.
4. RP02 & RP03 Step: Please install insert
type to bezel and direct connection
cables through brush opening prior to
tting RP02/03 to wall cavity.
5. Slide power point or alike through
the back of the RP0x on an angle
and push housing into cut out until
tight against the wall sheeting, if
the existing wall plate is too large
or cabling is too tight you may need
to disconnect the cabling from the
back of the wall plate and reconnect
through the RP0x.
6. If wall sheeting is of hard material
mark the locations of the 2 top ns
and the 2 bottom ns and make small
cuts until plastic shroud is located
rmly up against wall sheeting.
7. Insert the RP0x into the wall and
secure in place using the preinstalled
oating clips, one in each corner.
8. Position power point or alike into
the housing and using the 2 x 13mm
screws provided screw into the metal
brackets to secure in place.
9. Connect the RP0x cover. The RP0x
and the wall are now ready to be
painted if required.
HOW TO INSTALL IN EXISTING
BUILDS
1. Warning: To avoid re, shock or
death, turn off the power at the circuit
breaker or fuse and test the power is
off before continuing.
2. Unscrew existing point from wall
face and check for obstructions in
the wall to ensure the recessed point
will t and which side the stud or wall
trimmer is located.
3. Push back the existing wall point into
the wall cavity through the existing
stud bracket on an angle.
4. Taking the RP0x, locate the back of
it over the existing wall cut out so as
the existing bracket screw holes are
visible through the rear of the RP0x
screw points.
5. Mark the top and under side of the
housing from approximately the
centre of the RP0x across to the side
of the stud or trimmer.
6. Proceed to cut approx. 2mm above
the top line towards the stud until
stud is located. Cut approx. 2mm
lower than the bottom line in the same
direction until stud is located.
7. Place cut out template provided over
wall sheeting from the located stud
and across the direction of the 2 cuts
and mark around the template.
8. Continue cutting around the lines
noticing that you are cutting around
the existing bracket.
9. Cut vertically down the side where the
stud or trimmer is located and remove
the wall sheeting.
10. This will expose the existing bracket
inside the wall cavity ready for
removal, Pry the bracket off the stud
or trimmer and discard.
11. Continue with point 4 of “How to
install in new builds”.
If installing more than 1 recessed point,
ensure they are located more than 50mm
apart vertically and/or horizontally.
Designed for 70mm and 90mm wall
cavities.
Note: Screw length MUST NOT exceed
25mm
Warning: To be installed by a licensed
electrician or technician only. All power
should be switched off before installation.
Australian design registration numbers:
201815617, 201815619, 201815620, and
201815621
Power point not included.
Matchmaster Communications Pty Ltd
accepts no responsibility for any loss or
damage suffered by a person or their
property as a result of use or misuse, or
failure of these goods. In the case of any
defects within this product, Matchmaster
Communications Pty Ltd liability would
be limited to the replacement of this
product.
THIS IS A TEMPLATE FOR YOUR 04MM-RP01, RP02 & RP03 (168X120MM)
Questo manuale è adatto per i seguenti modelli
2
Altri manuali Matchmaster Accessori
