Matrix SATATYA Professional Series Manuale utente
SATATYA Professional Bullet IP-Camera
The Persistent Vision
Safety Instructions
Cautions
Warning
These instructions are intended to ensure that the user can
use the product correctly to avoid danger or property loss.
•Ensure that the power supply voltage is correct before using
the camera.
•Avoid placing cables too close to magnetic or high voltage
devices, to reduce undesirable image noise.
•Do not touch sensor modules with fingers. For cleaning use
‘clean cloth’ and wipe it gently.
•Do not mount the camera with the lens facing the sun or bright
light to prevent damage to the sensor.
•Do not expose the camera to temperatures below or beyond its
operating temperature.
•Do not mount the camera near a radiator or a heater.
•In the use of the product, you must be in strict compliance with
the electrical safety regulations of the region and nation.
•Do not connect several devices to one power adapter as it may
cause over-heating or fire hazard.
•If smoke, odour or noise rise from the device, turn off the
power at once and unplug the power cable, and contact the
nearest service center.
•To prevent electrical shock, turn off power supply before
making electrical connections.
11.19"
What your Package Contains
Things you will Need
Contents
Accessing Reset Pin and SD card slot
Accessing via Web Browser
4
7
8
Camera Variants
Installation
Network Configuration
Installing Mounting Template
Mounting the Camera
Adjusting the Camera Angle
Connecting cables
Please read this guide first for correct installation and retain it for future reference. The information
in this guide is prevailing at the time of publication. However, Matrix Comsec reserves the right to
make changes in product design and specifications without prior notice.
Copyright
All rights reserved. No part of this document may be copied or reproduced in any form or by any
means without the prior written consent of Matrix Comsec.
Warranty
Limited Warranty. Valid only if primary protection is provided, mains supply is within limit and
protected, and environment conditions maintained within product specifications. Complete
warranty statement is available on our website:
www.matrixvideosurveillance.com
Technical Specification
IP66 Protection Accessory Installation
Know your Camera
1. Cable Guide
2. Cable Assembly
3. Base Plate
4. Hole for Mounting
5. Pivot Joint
6. Camera Body
7. Screws for adjusting Camera Angle
8. Sunshield bolt
9. Sunshield
10. Lens (Fixed)
The Standard variant consists of 2 connectors: Power Connector and
Ethernet connector (POE).
The Premium variant consist of 4 connectors: Power Connector,
Ethernet Connector (POE), Audio IN and Audio OUT.
1
2
3
5
4
6
8
7
9
10
Know your Camera
5
5
11
11
13
14
4
15
18
19
23
5
Figure 1
What your Package contains
Things you will Need
Camera Variants
The Bullet Cameras are available in two variants; Standard and
Premium. Both the variants are available in 5MP with 2.8mm,
4.0mm and 6.0mm fixed focal length.
You can capture near and broader view with lens of 2.8mm
and 4.0 mm focal length. For example it can be used in ATM
and Elevators.
With lens of 6.0 mm focal length, far and narrow view can
be captured. For example it can be used in corridors or long
passage to capture long view.
6
5
Type of
Lens
Focal
Length
Fixed
4.0mm
6.0mm
MIBR50FL40CWS
Premium
Standard
MIBR50FL60CWS
2.8mm MIBR50FL28CWS MIBR50FL28CWP
MIBR50FL40CWP
MIBR50FL60CWP
Fixed
Fixed
ŸBullet IP Camera Unit
ŸWall Mounting Template
ŸWall Mounting Screws with Screw Grip (3 nos.)
ŸAllen Key
ŸCable Accessories for weather proofing
•A Power Drill, Screwdriver Set, Pliers, Wire-cutter, Ladder.
•Necessary Cabling
•A Power Supply with the recommended output voltage of
12V DC. Use an adapter to connect the camera to the power
outlet.
The respective available variants of Standard and Premium are
listed in below table,
You can insert SD card in camera to store recordings during
network failover and to upload image or clip as a result of event
trigger.
See page 15 to know how to open the camera and insert the SD
card.
Step 2: Prepare for Installation
Ensure that the necessary cabling to connect the camera to LAN
port and Power outlet are in place. The connecting cables from the
monitoring site should be ready at the installation site.
Step 1: Select a Location
Select a suitable location for your camera to enable coverage of the
intended surveillance area. The location should preferably be a flat
surface, such as a wall or a ceiling.
You can install the camera where cables are running through the
interior of the wall or ceiling as shown in Figure 2. Else cabling has to
be done through POE.
Installation
8
7
Step 3: IP66 Protection Accessory Installation
1. By default your camera contains the LAN connector fitted by IP66
protection accessory.
3. Rotate the middle part of IP66 assembly in anticlockwise direction
to detach the IP66 accessory from the LAN connector.
2. The IP66 protection assembly consist of tail end, middle part,
“IO” ring and LAN connector as shown below.
Tail end Middle
Part “O”ring LAN
Connector
Power cable
IP66 protection accessory
Before you start
Please make sure,
ŸThe device in the package is in good condition and all the
assembly parts are included.
ŸAll the related equipments are powered-off before installation.
ŸThe wall or ceiling is strong enough to support the weight of
camera.
Do not remove the “O” ring from its place.
LAN Connector
IP66 accessory
4. Loosen the tail end of the IP66 accessory by rotating it in
anticlockwise direction.
Ethernet cable
5. Insert the ethernet cable from behind. Then tighten the “tail end”
by rotating in clockwise direction to its maximum and crimp the
RJ45 connector.
10
9
6. Insert male RJ45 connector into female connector part. Then
tighten the middle part by rotating in clockwise direction.
Step 4: Installing Mounting Template
Wall Mounting: Figure 3
Ceiling Mounting: Figure 2
12
11
Mounting Template
Step 6: Adjusting the Camera Angle
Step 5: Mounting the Camera
•Stick the Mounting Template on the desired installation surface.
•Drill three holes through the markings of the Mounting Template
on Wall or Ceiling.
•Insert the screw grips in the holes you drilled.
•To avoid cable damage, take the Power, Ethernet, Audio IN,
Audio OUT, Alarm IN, Alarm OUT cables of the camera through
the cable guide on the base plate, see Figure 3.
•Align the screw holes on the base plate with those you drilled on
the installation surface.
•If the cabling is running through the interior of the wall or ceiling
behind the installation surface then, drill the hole (20mm approx)
on the center of the mounting template through the false ceiling.
Before you mount the base plate, pull the cables of the camera
through the hole drilled on the installation surface, see Figure 2.
•Secure the base plate of the camera on the installation surface
with the supplied screws.
•Use the Allen Key supplied to you to loosen the socket screws
on the pivot joint between the base plate and the camera body.
•Tilt the camera body to achieve the desired angle. You can turn
the camera upto 360 degrees.
•Hold it at the desired angle and tighten the socket screw with the
Allen key.
Socket screws
Allen Key
Pivot Joint
Camera body
Base Plate
14
13
1. You can connect the Audio Input device such as Mike to the
Audio Input cable of the camera. The audio when enabled will be
recorded with the video and will be available at the monitoring
location.
2. You may connect the Audio Output device such as earphone or
speaker to the Audio Output cable of the camera. This will
generate audio received from the network.
Step 6: Connecting Cables
Ethernet
12V DC @2A
Audio IN
Audio Out
Figure 4
Figure 5
•Connect the Ethernet cable to LAN port and Power cable to the
12V DC power supply.
•In Premium variants, connect the Audio I/O cables if required.
If devices such as Mike and Speaker can be connected to
Audio IN and Audio OUT, you may need to connect an external
power source if their power requirements are not fulfilled with
the camera adapter.
LED: CLASS1 (Category RS1)
Never look at the transmit laser while the power is on. Never
look directly at the fiber ports and the fiber cable ends when
they are powered on.
Use of controls or adjustment to the performance or procedure
other than those specified herein may result in hazardous laser
emission.
16
15
Power over Ethernet (PoE)
The IP camera is PoE- compliant, allowing transmission of power
and data via a single Ethernet cable connected to PoE switch.
If you forget the IP address or login credentials of camera then the
camera can be reset to factory default settings using the reset pin.
Accessing Reset Pin and SD card slot
To access the Reset pin
1. Open the Sunshield by removing the sunshield screw.
Sunshield
Sunshield
Screw
2. Open the front cover by rotating it in the anti-clockwise
direction.
Front cover
3. Press the Reset switch for minimum 5 sec and release the
switch to reset the camera to default settings.
Reset Pin
Figure 6
Figure 7
Figure 8
4. You can insert the SD card in the slot to store your camera
recordings.
SD Card Slot
18
17
Network Configuration
Figure 9
To view and configure the camera via LAN (Local Area Network),
you need to connect the network camera in the same subnet with
your PC. Then install the software to configure the IP address.
Steps to get the IP address
•Once the camera is connected to the network, it will
automatically be assigned a dynamic IP address by the DHCP
server. You can view the assigned IP address through any IP
scanner utility.
•If DHCP server is unavailable or is not able to provide an IP
address then 192.168.1.126 will be set as default IP address.
•You can change the IP address and subnet mask of Camera from
the Basic Settings page of camera.
After Reset or SD card insertion, you may need to set the
camera focus and camera angle.
Accessing via Web Browser
The IP cameras are supported by Microsoft Windows Operating
System.
Steps:
20
19
192.168.1.126
•Run the web browser as administrator.
•In the browser address bar, type the IP address of the camera
e.g., 192.168.1.126 and press the Enter key to open the login
interface.
192.168.1.124
192.168.1.126
•Enter the User Name and Password.
•By default, you can login with User Name as admin, operator or
viewer with the password as admin, operator and viewer
respectively.
•Click on Login.
ŸThe browser will ask you to install ActiveX control.
ŸClick on Run Add-on to install the plugin.
In Internet Explorer you can access the camera with Matrix
ActiveX plugin. In other browsers you need to install
Quicktime or VLC plugin.
Altri manuali per SATATYA Professional Series
1
Questo manuale è adatto per i seguenti modelli
6
Indice
Altri manuali Matrix Telecamera di sicurezza
Matrix
Matrix SATATYA PZCR20ML25CWP Manuale utente
Matrix
Matrix SATATYA PZCR20ML25CWP Guida utente
Matrix
Matrix SATATYA Professional Series Manuale utente
Matrix
Matrix SATATYA Project Series Manuale utente
Matrix
Matrix SATATYA PZCR50ML42CWP Manuale utente
Matrix
Matrix SATATYA PZCR20ML33CWP Guida utente
Matrix
Matrix SATATYA PZCR50ML42CWP Guida utente
