Matt:e B60 Manuale utente
B60
Domestic Voltage
Optimisation Unit
Installation Manual
V2.3 Oct 2014
B60 Voltage Optimisation Unit
2 | P a g e
PRODUCT ADVISORY NOTICE
This product must be installed by a competent person
in accordance with the IEE Wiring Regulations,
BS7671 (17th Edition or later) and current Building
Regulations.
Ensure the electrical supply is disconnected before
installation or removing the cover of the B60 unit.
B60 Voltage Optimisation Unit
3 | P a g e
Contents
Product Description 4
Warning Notice 4
Safety Advice 4
Introduction 5
Installation
Typical Installations 6
Dimensions & Mounting the unit 7
Electrical Connections 9
Specifications 11
B60 Voltage Optimisation Unit
4 | P a g e
Once installed, the unit has a Live Mains Supply
(230v or higher) within the enclosure. The cover
must not be removed until the supply to the unit
has been isolated or disconnected.
Product Description
The single phase matt:eB60 Voltage Optimisation unit is designed for use in
domestic and light commercial / retail applications.
Installed between the electricity meter and main consumer unit, the matt:eoffers 18
volt subtractive performance.
The unit is not intended for any purpose other than that defined within this
document.
WARNINGS
Please read and observe the following notices carefully. These warnings must be
observed when installing and operating the Domestic Voltage Optimisation unit.
All relevant supplies must be isolated or disconnected before commencing any
work.
This product must be installed by a competent person in accordance with the IEE
Wiring Regulations, BS7671 (17th Edition or later) and any relevant Building
Regulations.
Safety Advice
The unit must be installed in a dry ventilated location, it must never be covered or
have restricted ventilation.
The matt:eB60 voltage optimisation unit is rated for a maximum 14kW load.
For any information not contained within this document, please contact our
technical support team on 01782 473002.
B60 Voltage Optimisation Unit
5 | P a g e
Introduction
The matt:eB60 is a single phase Voltage Optimisation unit.
The unit reduces the incoming supply voltage by 18v (i.e.: a 240v supply
would be reduced to 222v). It is designed to be connected in series with the
incoming supply installed between the main electricity meter for the dwelling,
and the consumer unit.
The matt:eB60 has short circuit, overload and thermal protection built in.
Rated at 14kW, the unit is suitable for the majority of domestic and light
commercial / retail installations.
B60 Voltage Optimisation Unit
6 | P a g e
Typical Installation
Grid Power
VO Power
Distribution Board
matt:e B60 VO unit
Suppliers
Meter
Suppliers
Fuses
Suppliers
Isolator
B60
Danger 230Volts
Maximum Load 60A
!
Caring about your world
Made in Britain
Made in Britain
B60 Voltage Optimisation Unit
7 | P a g e
Mounting the unit
The unit is designed to be installed between the main electricity meter and consumer
unit in the most practical and accessible position available.
The installation location should be clean, dry and well ventilated.
Please refer to the diagram below for the dimensions and mounting arrangements of
the unit.
NOTE: The unit weighs approximately 10.0kgs. Always handle the unit with both
hands.
B60
Danger 230Volts
Maximum Load 60A
!
Caring about your world
Made in Britain
Made in Britain
B60 Voltage Optimisation Unit
8 | P a g e
Fixing Dimensions
B60 Voltage Optimisation Unit
9 | P a g e
Electrical Connections
The unit is supplied with a 63 Amp miniature circuit breaker that provides overload
and short circuit protection for the unit.
The transformer is fitted with an embedded thermal switch. Should the temperature
of the transformer increase beyond acceptable levels the thermal switch will operate
and automatically shut off the supply to the transformer by ‘tripping’ the incoming
MCB (CP1). Once the transformer temperature has returned to an acceptable level
the thermal switch will reset and the MCB can be closed.
The user wiring connections are indicated in the diagrams below:
On completion of installation the tightness of all electrical connections should
be checked.
B60 Voltage Optimisation Unit
10 | P a g e
Typical Retrofit with PV
matt:e B60 (V2)
Voltage Optimiser
Consumer Unit
Suppliers
Meter
Suppliers
Isolator
PV
Inverter
AC
Isolator Henley
Type
Blocks
Indice
Altri manuali Matt:e Unità di distribuzione dell'energia
