Maxitrol Selectra MP2+ Manuale utente

Multiple Program Process Temperature Controller

Installation Guide

www.maxitrol.com



Please read these instructions fully prior to attempting to in-

stall, operate, and/or maintain the MP2+ system. Failure to do

so may result in improper operation and/or component dam-

age.

Installation shall conform with local codes, or in the absence

of local codes, in accordance with the National Fuel Gas Code

ANSI Z223.1/NFPA54 or CSA B149.1 as is applicable, and op-

erated in accordance with the manufacturer’s instructions.

These instructions do not supersede OEM’s installation or op-

erating instructions. Installation, inspection, and replacement

must be performed by a qualiﬁed installer or gas supplier.

This control must be electrically wired in accordance with lo-

cal codes, or in the absence of local codes, with the Nation-

al Electrical code, ANSI/NFPA 70 or the Canadian Electrical

Code, CSA C22.1 as applicable.

Warnings

Inappropriate and/or improper installation, adjustment, al-

teration, service or maintenance can cause property dam-

age, injury or death. Read the installation, operating and

maintenance instructions thoroughly before installing or

servicing this equipment.

Disconnect power before installation to prevent electrical

shock or equipment damage.

FOR YOUR SAFETY

If you smell gas: 1 Open windows.

Do not touch electrical switches.

Extinguish any open ﬂame.

Immediately call your gas supplier.

FOR YOUR SAFETY

The use and storage of gasoline or other ﬂammable va-

pors and liquids in open containers in the vicinity of this

control or other appliance is hazardous.

Warnings ............................................................................................................. 2

General Statement ............................................................................................... 3

Contents .............................................................................................................. 3

Technical Data .................................................................................................... 4

Components ........................................................................................................ 4

Dimensions ......................................................................................................... 5

Wiring Diagrams ................................................................................................. 6

Installation ........................................................................................................... 8

MP2+ Process Control System ............................................................... 8

MP2+ Process Control System w/

TM02 Multifunctional Timer Control ..................................................... 9

Glossary ............................................................................................................ 10

Contents

The MP2+ system is intended for multiple low temperature process ap-

plications, for example paint spray booths or other curing processes. It is

ideal for multiple temperature critical and time sensitive process applica-

tions requiring temperatures from 60°F to 240°F.

General Statement

Please refer to the MP2+ User’s / Programming

Guide for programming instructions.

NOTE:

The technical data listed in this manual does not include normal op-

erating deviations that occur in the actual manufacturing process.

The listed speciﬁcations may not meet the individual unit’s actual

speciﬁcations. Slight deviations in an individual unit’s performance

may be encountered due to possible changes in the controlled con-

ditions in which the unit is tested and calibrated. Check ratings

given in OEM instructions to assure the MP2+ is suitable for the

application.

Technical Data

NOTE:

Please read safety warning instructions fully for Maxitrol Modulator

Valves [MI2040] prior to attempting to install, operate, and/or main-

tain the MP2+ system.

Components

AM02+ Ampliﬁer

TDM02 Remote Selector Display Interface

TM02 Auxiliary Multifunctional Timer Control (optional)

Standard 6 Position 4 Conductor Telephone Cable, 3 feet

Ethernet Patch Cord, 3 feet



Power

Requirements

TDM02

AM02+

TM02

Ambient

Temperature

Limits

Connections

Valves

Sensor

Independent 24 VAC, 40 VA capacity transformer

Operating: -40°F(-40°C) to 158°F(70°C)

Non-operating: -40°F(-40°C) to 185°F(85°C)

Operating,

Non-operating: -40°F(-40°C) to 185°F(85°C)

AM02+ to TDM02 = Standard 6 Position 4 Conductor

Telephone Cable

AM02+ to TM02 = Ethernet Patch Cord

1,000 ohm RTD TS194Q use with mixing tube

M411, M511, M611, MR212

Display Interface

Std. - 1/4 DIN

Panel Mounted

Cover = 4.06” W x 4.06” D

Panel Cutout = 3.53” W x 3.53” H

Depth = 1.08” D

7.5” W x 3.38” H x 1.89” D

Mounts on supplied Snap Track

5.25” W x 3.75” H x 1.75” D

Mounts on supplied Snap Track

TDM02

AM02+

TM02

Dimensions

(see Wiring Diagram, page 6)

Process Indication Output

The TM02 multifunctional timer control features a Process Indication Out-

put. Processes 1 thru 8 have a dedicated pair of terminals, labeled 1 thru 8

on the TM02. An indicator (LED, relay coil, etc...) 24 VDC 2W maximum

can be wired directly to the corresponding terminal block for each Pro-

cess to be indicated. Note Polarity

Controller in the “READY” position

Controller operating in any of the 8 processes making up a Program

0 VDC

24 VDC 2W max

Program Indication Output

Terminal #9 is used to indicate the controller is operating within a Pro-

gram. The following voltage will be measured across the #9 terminals:

Note Polarity

Other Features

Wiring Diagrams

24VAC

VALVE

1k PLT RTD

SW1

OPEN

TB1

TB2

RELAY8

TB2

RELAY1

AM02+

TDM02

TM02

(OPTIONAL)

- + - + - + - + - + - +

Ethernet

Patch Cable

Normally open device to momentarily

latch a set of contacts.

Multiple devices to be wired in parallel.



Lockout Switch Settings

(see ﬁgure B, page 7)

Fig. A

Wiring Diagram

24VAC

- +

Standard 6 Position 4 Conductor

Telephone Cable

TB1

- +

Note Polarity

OPEN

Wiring Diagrams

Fig. B

Lockout Switch Settings, SW1

Level 0 Level 1 Level 2 Level 3

Level SW1 Dipswitch position Accessible Menus

0 1-closed, 2-closed None

1 1-open, 2-closed Process

2 1-closed, 2-open Process and Operation

3 1-open, 2-open Process, Operation and Diagnostic

Getting Started

Install Components. For the dimensions of components see

Dimensions, page 5.

Wire the MP2+ System as shown in ﬁgure A, page 6.

Apply 24 VAC power to AM02+.

MP2+ System will default to Process 1 of Program #1.

NOTE: Any power interruption to the AM02+, will cause the MP2+ System

to default to the Process 1 position of the program in use regardless of the

Process position prior to the power interruption.

Enter into the Program Mode and program the MP2+ System as needed

(see the MP2+ User’s / Programming Guide).

After programming, the MP2+ System will default to Process 1 of

the current program.

Set the Programming Lockout feature to the appropriate user access

(see ﬁgure B, page 7).



Installation

MP2+ Process Control System

Getting Started

Install Components. For the dimensions of components see

Dimensions, page 5.

Wire the MP2+ System and TM02 together as shown in ﬁg. A, page 6.

Apply 24 VAC power to AM02+ and TM02.

MP2+ System will default to the “READY” program start position

of Program #1.

NOTE: Any future power interruption to the AM02+, will cause the MP2+

System to default to the selected program start position of the program in use

prior to the power interruption (“READY” or First Process).

Enter into the Program Mode and program the MP2+ System as need-

ed (see the MP2+ User’s / Programming Guide).

After programming, the MP2+ System will default to the selected

program start position “READY” or First Process of the program in

use prior to programming.

“READY”:

Start Process 1 of the program by pushing and releasing Button 1

or momentarily latching (make) a set of contacts wired to the TB1

terminal (i.e. typically accomplished by a momentary ON (normally

open) switch).



MP2+ Process Control System w/

TM02 Multifunctional Timer Control

Installation

Glossary

Process

A single programmed temperature, or single programmed temperature

and time.

Program

The combination or series of Processes.

“Ready”

Screen display. When selected, it appears prior to the start of a program

involving timed processes. A momentary switch closure moves the con-

troller from the “Ready” position to the First Process.

Programming Lockout Switch

When set, this feature can limit user access to programming menus (see

ﬁgure B, page 7).

Altri manuali per Selectra MP2+

Indice

Altri manuali Maxitrol Regolatori di temperatura

Maxitrol

Maxitrol Selectra MP2+ Istruzioni operative

Manuali Regolatori di temperatura popolari di altre marche

Swegon

Swegon LUNAd MB Manuale utente

Lucky Reptile

Lucky Reptile Thermo Control II Manuale utente

SENSORMETRIX

SENSORMETRIX Argon 100 Manuale utente

Fuji Electric

Fuji Electric PXE4 Manuale utente

Yuyao gongyi

Yuyao gongyi XMT-808 series Manuale utente

Selec

Selec TC544C Manuale utente

P.W. KEY

P.W. KEY rt-208gt Manuale utente

Future Design

Future Design FDC-9200 Manuale utente

BH Thermal

BH Thermal BriskONE Manuale utente

Omron

Omron E5EX-H Manuale utente

West Control Solutions

West Control Solutions KS 45 Guida rapida

MCS

MCS RITC-15B Manuale utente

SMC Networks

SMC Networks Thermo-con INR-244-639 Manuale utente

eltherm

eltherm Ex-TC It Series Manuale utente

Omron

Omron C200H-TV Series Manuale utente

industrie technik

industrie technik CA1 Manuale utente

KRAL

KRAL EET 32 Manuale utente

dixell

dixell XR420C Schema elettrico